A novel quasi-oppositional harmony search algorithm and fuzzy logic controller for frequency stabilization of an isolated hybrid power system

The intermittent wind power in isolated hybrid distributed generation (IHDG) may cause serious problems associated with frequency (f) and power (P) fluctuation. Energy storage devices such as battery, super capacitor, and superconducting magnetic energy storage (SMES) may be used to reduce these fluctuations associated with f and P. This paper presents a study of IHDG power system for improving both f and P deviation profiles with the help of SMES. The studied IHDG power system is consisted of wind turbine generator and diesel engine generator. Both f and P control problems of the studied power system model are addressed in presence or absence of SMES. Fuzzy logic based proportional–integral–derivative (PID) controller with SMES is used for the purpose of minimization of f and P deviations. The different tunable parameters of the PID controller and those of the SMES are tuned by a novel quasi-oppositional harmony search algorithm. Performance study of the IHDG power system model is carried out under different perturbation conditions. The results demonstrate minimum f and P deviations may be achieved by using the proposed fuzzy logic based PID controller along with SMES.     

Nonlinear response in glass fibre non-crimp fabric reinforced vinylester composites

This paper addresses the nonlinear stress-strain response in glass fibre non-crimp fabric reinforced vinylester composite laminates subjected to in-plane tensile loading. The nonlinearity is shown to be a combination of brittle and plastic failure. It is argued that the shift from plastic to brittle behaviour in the vinylester is caused by the state of stress triaxiality caused by the interaction between fibre and vinylester. A model combining damage and plasticity is calibrated and evaluated using data from extensive experimental testing. The onset of damage is predicted using the Puck failure criterion, and the evolution of damage is calibrated from the observed softening in plies loaded in transverse tension. Shear loading beyond linear elastic response is observed to result in irreversible strains. A yield criterion is implemented for shear deformation. A strain hardening law is fitted to the stress-strain response observed in shear loaded plies. Experimental results from a selection of laminates with different layups are used to verify the numerical models. A complete set of model parameters for predicting elastic behaviour, strength and post failure softening is presented for glass fibre non-crimped fabric reinforced vinylester. The predicted behaviour from using these model parameters are shown to be in good agreement with experimental results.     

High-temperature stability of Mg(Al,Cr)2O4 spinel co-existing with calcium aluminates in air

Cr₂O₃ is a well-known corrosion resistant oxide used in refractory applications. However, it can oxidize into toxic and water-soluble Cr(VI) compounds upon reaction with calcium aluminate cement phases in the presence of oxygen, which subsequently causes disposal problems after use. This study describes the extent to which chromium in the spinel Mg(Al,Cr)₂O₄ phase can be oxidized to Cr(VI) when it reacts with the calcium aluminate cement phases C₁₂A₇, CA, CA₂ and free CaO at 1300 °C in air, using XRD, XPS and leaching tests (TRGS 613 standard) as analytical tools. On reaction with CaO, the Mg(Al,Cr^III)₂O₄ spinel mainly transformed into hauyne (Ca₄Al₆Cr^VIO₁₆) and Ca₅Cr₃O₁₂ which contains both Cr(IV) and Cr(VI). The reaction of C₁₂A₇ and CA with the spinel phase also resulted in the formation of Ca₄Al₆CrO₁₆. Conversely, the reaction of Mg(Al,Cr^III)₂O₄ spinel with CA₂ resulted in the formation of only a trace amount of Cr(VI). Water-soluble Cr(VI) leached in large quantities (>100 mg/L) from samples where the Mg(Al,Cr^III)₂O₄ reacted with either C₁₂A₇ or CA. Almost no Cr(VI) leached from the sample when Mg(Al,Cr^III)₂O₄ reacted with CaO, using the standard TRGS 613 leach test, but a significant amount of Cr(VI) was released into solution when leached with a HCl solution for 12 h. Both Cr(IV) and Cr(VI) present in the Ca₅Cr₃O₁₂ dissolved into acidic solution. Only a small amount of Cr(VI) leached from the sample that resulted when spinel was reacted with CA₂, even after a prolonged HCl leach. Cr(III) in spinel Mg(Al,Cr)₂O₄ is very stable and does not leach in either distilled water or acidic solution.     

豫西雷门沟钼矿水文地质条件分析及涌水量预测

豫西熊耳山雷门沟钼矿床位于东秦岭多金属成矿带东段,是已探明的超大型斑岩型钼矿,前人研究程度高、地质成果丰硕,但对矿床开采技术条件方面研究较少。本次通过地质调查工程、水文地质试验等方法,从水文地质角度,对雷门沟钼矿床水文地质条件进行研究,填补了该方面的空白,丰富了研究成果；采用水文地质比拟法预测未来矿坑最大排水量2613 m³/d,经实践检验结果较为可靠；总结的采坑排水量预测方法、含水层特点、矿床充水因素以及防治水措施,以期对该区域水文地质工作具有参考价值。     

Templated titania films with meso- and macroporosities

Porous TiO₂ films with both mesoporosity and macroporosity were fabricated by a templated sol–gel method for applications, such as dye-sensitized solar cells (DSC), photocatalysis and catalysis. With the incorporation of differently sized pores, the resultant structures exhibit high surface areas and possess interpenetrating aligned pore channels, which are believed to be beneficial for applications where diffusion of reactants to interior surface can be rate limiting. Both liquid and solid TiO₂ precursors can be applied for large area coating in this process. Almost crack-free films were produced by templated coating of pre-synthesized TiO₂ nanoparticles. The measured specific surface area and porosity of synthesized films were in the range of 33–137 m²/g and 61–80%, respectively, depending on the size of the selected template.     

基于纹理特征的三维点云数据配准算法研究

使用Kinect可以方便地获取物体的纹理图像和三维点云数据。研究一种通过获取纹理图像的特征点进行快速三维点云数据配准的算法．并最终应用到室内环境的三维场芾重建中。实验表明,此算法具有直观、实现简单、运算量小等优点。     

地震断裂带高铁大跨拱桥深基坑钢板桩围堰支护试验与监测

针对大跨度高速铁路拱桥建设对深基坑开挖施工的安全性要求,为了研究钢板桩围堰支护在大跨度高速铁路拱桥深基坑施工中的可行性,以新建徐盐高铁徐洪河特大桥工程项目为依托,通过数值模拟及现场试验监测,对深基坑钢板桩围堰支护在施工过程中的形变及受力情况进行分析。结果表明:通过有限元模拟分析,钢板桩围堰最危险受力点处于钢板桩中部、中上部及四角连接处,围堰第4道内支撑内力较其他3道内支撑大。整个施工过程中工况5为施工最不利工况。由监测结果可知,在施工过程中钢板桩单日最大位移值为2.8mm,最大累计位移值为24.0mm,均未达到预警值,施工过程中钢板桩形变稳定。钢支撑轴力受基坑周边荷载的影响明显,围堰钢支撑最大压力值为147.31kN,最大拉力值为24.95kN,未达到预警值,结构安全。研究结果可供同类型工程施工参考。     

让案例教学走进高职计算机学科

"案例教学法"(CaseStudy)是一种以案例为基础的教学法,把真实的情景进行典型化处理后供学生思考分析和决断,让学生分组自助谈论和研究,从而提高学生对于问题的分析和解决的能力。     

水泥棒磨机预粉磨技术的增产节能效果

随着水泥工业结构调整，传统的一级圈流短磨水泥粉磨系统已经难以满足高产、优质、低耗的产业政策要求，必须进行必要的技术改造。文章分析了一级圈流磨存在的技术问题及其产生原因，介绍了对其实施增产节能改造的系统工艺技术方案和主机设备的内部结构改造方案。从两个厂的改造实施情况看，技改效果显著。     

《数据结构》精品资源共享课建设探析

《数据结构》精品资源共享课作为服务于高校师生和社会学习者的平台之一,其建设内容主要由基本资源、拓展资源、师生互动组成。在《数据结构》精品资源共享课建设中,明确建设目标,着重进行课程体系及课程资源建设。通过精心组织课程资源,优化师资队伍以及制定科学的课程管理办法等措施,实现资源共享。