半合成发动机油基础油调配的仿真研究

采用矿物油、聚α-烯烃、多元醇酯和高压加氢BS光亮油调配半合成发动机油基础油,并测定不同配比下基础油的油膜强度、摩擦系数和粘度指数,通过双隐层BP神经网络对基础油调配进行仿真研究,建立了半合成发动机油基础油调配配方优化模型,经过优化训练后,最终得出综合性能优良的配方组合。按49.9957∶4.3693∶42.4578∶3.1772的配比调配基础油,可以使基础油的油膜强度、摩擦系数和粘度指数分别达到56 kg,0.065和112,经实验后仿真结果与实验结果(56 kg;0.065598;112)极其吻合。     

锂离子电池有机电解液成膜添加剂的研究现状

文章综述了锂离子电池有机电解液成膜添加剂的作用原理，具体介绍了CO2、SO2、VC化合物、卤化物、有机铜盐以及马来酐等添加剂的研究现状。     

Oil agglomeration of a lignite treated with microwave energy: Effect of particle size and bridging oil

Oil agglomeration of Sivas–Divriği (S–D) Uluçayır lignite fines was carried out using kerosene and kerosene–extract oil (which was obtained from lignite treated with microwave energy) mixture as a bridging oil. The effects of parameters such as the amount and type of bridging oil, microwave time and particle size on the agglomeration performance were investigated. The amount of kerosene was varied from 5 to 30 wt.% of the initial lignite loading. The values of the grade and recovery increased with an increase in the amount of kerosene added. Extract oil fraction of the lignite extract at various ratios in kerosene increased the agglomeration recovery from 95.88% to 98.55%. The effect of microwave time was investigated and it was found that the grade was also increased with increasing microwave time (4, 8 and 10 min). The grade of char (microwave time: 8 min) was increased in comparison with the original lignite while decreasing its recovery. Dense medium separations of the lignite were conducted and the results of their grade recovery performances were compared with those of agglomeration of the particles. During the inspection of particle size effect on the dense medium separation, the recovery was increased remarkably (from 12.07% to 89.50%) with increasing particle size, while decreasing the grade (from 0.732 to 0.697). In the oil agglomeration of lignite the recovery values were increased with increasing particle size.     

Facile route to fabricate large-scale silver microtubes

Large-scale uniform Ag microtubes with high length diameter ratios have been first successfully synthesized by a facile approach, using low-cost super fine glass fibers as templates. The samples were characterized by SEM and XRD. The investigations showed that calcining or adding of PEG-1000 and alcohol could greatly improve the mechanical strength of the sample. Especially the products exhibited favorable catalytic properties during the degradation of Rhodamine B by NaBH₄.     

The influence of Johnson–Cook material constants on finite element simulation of machining of AISI 316L steel

In literature, five different sets of work material constants used in the Johnson–Cook's (J–C) constitutive equation are implemented in a numerical model to describe the behaviour of AISI 316L steel. The aim of this research is to study the effects of five different sets of material constants of the J–C constitutive equation in finite-element modelling of orthogonal cutting of AISI 316L on the experimental and predicted cutting forces, chip morphology, temperature distributions and residual stresses. Several experimental equipments were used to estimate the experimental results, such as piezoelectric dynamometer for cutting forces measurements, thermal imaging system for temperature measurements and X-ray diffraction technique for residual stresses determination on the machined surfaces; while an elastic–viscoplastic FEM formulation was implemented to predict the local and global variables involved in this research. It has been observed that all the considered process output and, in particular the residual stresses are very sensitive to the J–C's material constants.     

注射成形粘结NdFeB磁体:工艺·性能·应用

综合介绍了几种适于注射成形粘结NdFeB磁体的磁粉制备方法及特点；讨论了粘结剂、改性剂及磁场取向对注射成形NdFeB磁体最终磁性能的影响及其应用市场。在此基础上，指出了今后开展研究工作的方向。     

Delayed failure of ceramic matrix composites in tension at elevated temperatures

Ultimate tensile strength of five different continuous fiber-reinforced ceramic matrix composites (CMCs), including SiC_f/BSAS (two dimensional (2D), 2 types), SiC_f/MAS (2D), SiC_f/SiC (2D), and C_f/SiC (2D, 2 types), was determined as a function of test rate at 1100–1200 °C in air. All five CMCs exhibited a significant dependency of ultimate tensile strength on test rate such that the ultimate tensile strength decreased with decreasing test rate. The dependency of ultimate tensile strength on test rate, the applicability of preload technique, and the predictability of life from one loading configuration (constant stress-rate loading) to another (constant stress loading) all suggested that the overall, phenomenological delayed failure of the CMCs would be governed by a power-law type of slow crack growth.     

纳米α-Fe的合成及分散

在甲醇-水体系中以NaBH4还原二价铁离子,得到了粒径为10～40nm的α-Fe金属粒子。在反应体系中加入右旋糖苷等分散剂以强化产物颗粒的分散。采用X射线衍射及透射电镜等测试方法对合成产物进行检测。结果表明,以湿化学还原法能合成纳米α-Fe金属粒子,但产物呈现网状团聚状态;右旋糖苷能很好地分散产物团聚体,在其作用下产物颗粒呈稳定的分散状态。