Effect of aluminium acetyl acetonate on the hydrogen and nitrogen permeation of carbon molecular sieves membranes

With a growing interest in hydrogen as energy carrier, the efficient purification of hydrogen from gaseous mixtures is very important. This paper addresses the separation of hydrogen using Carbon Molecular Sieves Membranes (CMSM), which show an attractive combination of high permeability, selectivity and stability. Supported CMSM containing various amounts of aluminium have been prepared from novolac and aluminium acetyl acetonate (Al(acac)₃) as carbon and alumina precursors. The thickness of the CMSM layers depend on the content of Al(acac)₃ in the dipping solution, which also has influence in the pore size and pore size distribution of the membranes. The permeation properties of the membranes against the Al content in the membrane follows a volcano shape, where the membrane containing 4 wt (%) of Al(acac)₃ has the best properties and was stable during 720 h for hydrogen at 150 °C and 6 bar pressure difference. All the CMSM have permeation properties well above the Robeson Upper limit.     

Model repair — aligning process models to reality

Process mining techniques relate observed behavior (i.e., event logs) to modeled behavior (e.g., a BPMN model or a Petri net). Process models can be discovered from event logs and conformance checking techniques can be used to detect and diagnose differences between observed and modeled behavior. Existing process mining techniques can only uncover these differences, but the actual repair of the model is left to the user and is not supported. In this paper we investigate the problem of repairing a process model w.r.t. a log such that the resulting model can replay the log (i.e., conforms to it) and is as similar as possible to the original model. To solve the problem, we use an existing conformance checker that aligns the runs of the given process model to the traces in the log. Based on this information, we decompose the log into several sublogs of non-fitting subtraces. For each sublog, either a loop is discovered that can replay the sublog or a subprocess is derived that is then added to the original model at the appropriate location. The approach is implemented in the process mining toolkit ProM and has been validated on logs and models from several Dutch municipalities.     

Performance evaluation of noise reduction method during on-line monitoring of MV switchgear for PD measurements by non-intrusive sensors

Partial Discharge (PD) measurement is a globally accepted method for insulation diagnosis of electrical assets. The consequences of insulation breakdown are well known. The trend is to move from conventional offline testing to online monitoring for insulation life prediction, which results in the inclusion of high frequency noise in the captured signals. Therefore de-noising is of paramount importance in online monitoring to obtain useful information from the signal.In this research, a 20 kV switchgear panel has been subjected to PD faults in the laboratory and measurements have been carried out by using different non-intrusive sensors including a novel sensor, the D-dot sensor and recorded by a high frequency oscilloscope. The measured results show the effective applicability of sensors for switchgear. The Discrete Wavelet Transform (DWT) has been used to de-noise PD signals in this paper. Time domain and frequency domain comparison of original and de-noised PD signals reveals the significance of this technique for online monitoring of Medium Voltage (MV) switchgear. Finally, an adaptive online de-noising concept, based on automatic de-noising is also proposed in this paper.     

The PAR(p) Interconfigurations model used by the Brazilian Electric Sector

This study discusses the characteristics of the Periodic Autoregressive model, PAR(p), which is used to generate synthetic series of inflow energies that serve as entries for computer platforms that implement the planning and expansion of the operations of the BES – the Brazilian Electric Sector (SEB – Sistema Elétrico Brasileiro). The methodology for the design of a generating plant is presented in addition to the fundamentals of the “PAR(p) Interconfigurations” Model, which is referred to as the Inflow Energy Generation Model (IEGM) in this study. The major contribution of this study is to provide the first scientific discussion of the representation of multiple configurations using the PAR(p) model. For this purpose, several topics related to the time series are discussed, such as the definition of the model order, the matter of stationarity and the need to address possible outliers. Finally, a case study is presented, wherein the results of the estimation and generation of the described model’s scenarios are demonstrated.     

On the origin of strain hardening in glassy polymers

The influence of network density on the strain hardening behaviour of amorphous polymers is studied. The network density of polystyrene is altered by blending with poly(2,6-dimethyl-1,4-phenylene-oxide) and by cross-linking during polymerisation. The network density is derived from the rubber-plateau modulus determined by dynamic mechanical thermal analysis. Subsequently uniaxial compression tests are performed to obtain the intrinsic deformation behaviour and, in particular, the strain hardening modulus. At room temperature, the strain hardening modulus proves to be proportional to the network density, irrespective of the nature of the network, i.e. physical entanglements or chemical cross-links. With increasing temperature, the strain hardening modulus is observed to decrease. This decrease appears to be related to the influence of thermal mobility of the chains, determined by the distance to the glass-transition temperature (T−T_g).     

Prediction of brittle-to-ductile transitions in polystyrene

In this study it is attempted to predict brittle-to-ductile transitions (BDTs) in polystyrene blends, induced either by an increase in temperature or by a decrease in inter-particle distance. A representative, two-dimensional volume element (RVE) of a polystyrene matrix with 20% circular voids, is deformed in tension. During deformation a hydrostatic-stress based craze-nucleation criterion [1] is evaluated. The simulations demonstrate that crazes initiate at low temperatures while a transition from crazing to shear yielding (BDT) is found around 75 °C. The numerical results correlate well with tensile tests on similar heterogeneous polystyrene. The presence of an absolute length, as experimentally found, is more difficult to explain. Near a free surface a T_g-depression is measured for polystyrene and also the resistance to indentation in polystyrene is lower than expected from bulk properties. Both observations are rationalised by an enhanced segmental mobility of chains near a free surface. As a consequence of these findings, an absolute length-scale could be incorporated in the numerical simulations. For simplicity, the length-scale is modelled by taking a temperature gradient over a thin layer near the internal free surfaces of the RVE. Deformation of the RVE with different absolute length-scales shows that indeed also the experimentally found brittle-to-ductile transition can be predicted if the ligament thickness between the inclusions (‘voids’) in polystyrene is below a critical value of ca. 15 nm.     

The measurement of the diffusion coefficient and the sorption isotherm of water in paint films

An experimental technique together with a numerical model is proposed with which the diffusion coefficient and the sorption isotherm of water in paint can be measured. Inside a closed vessel, paint films are on stainless-steel plates. Water is present as water vapour in the air and in the paint. After blowing dry or wet air through the vessel for some time, the situation moves to a new equilibrium. The relative humidity of the air inside the vessel is measured as a function of time. From fitting the theoretical/numerical model against the experimental values, follow the diffusion coefficient and the sorption isotherm of water in the paint. The results show large scattering. When the independently measured sorption isotherm is used as an input parameter in the model, the fitting procedure gives much smaller scattering for the diffusion coefficient.     

Behavior of a vibrating wire near the liquid3He-vacuum interface and in a saturated3He-4He mixture

In this paper we describe the effect of the vicinity of a liquid³He-vacuum interface on the behavior of a vibrating wire viscometer. It was found that in the fluid near the liquid interface the quality factor is lower than in the bulk liquid. We further report on the observation of a doubling of the resonance peak of the wire in a saturated³He-⁴He mixture. The frequencies and amplitudes of the two peaks strongly depend on the distance between the phase boundary and the vibrating wire; the temperature and the velocity of the phase boundary have no significant influence on the peak frequencies. The observed peak doubling is attributed to the coupling of the vibrating wire with a standing second-sound wave in the dilute phase where the volume of the dilute phase can be regarded as a resonating cavity for second sound.