Preparation of biaxially textured Ce1-x(Y0.2Zr0.8)xOδ buffer layers on RABiTS NiW tapes by chemical solution deposition

Highly (100)-oriented Ce_1-x(Y_0.2Zr_0.8)_xO_δ (CYZO) films were prepared on biaxially textured NiW substrates by a chemical solution deposition approach using metal inorganic salts as starting materials. It has been found that both the preferential orientation and surface roughness of CYZO films decrease gradually with increasing of the doping percentage of Y³⁺ and Zr⁴⁺ ions. The epitaxial growth relationship of (220)_CYZO//(200)_NiW and [00?l]_CYZO//[001]_NiW was demonstrated by XRD texture measurement as well as atomic resolution STEM observation. XRD, Raman and XPS spectra results indicate that Y³⁺ and Zr⁴⁺ ions were indeed introduced into CeO₂ lattice to substitute Ce⁴⁺ ions and form cubic fluorite CYZO solid solution. Moreover, CeO₂ buffer layer can be endowed a strong enough capability to prevent element diffusion through co-doping of yttrium and zirconium, provided that an optimal doping ratio of them is adopted. This will provide a new approach to fabricating strong-barrier single buffer layer for coated conductor.     

GRU-based capsule network with an improved loss for personnel performance prediction

Applied Intelligence - Personnel performance is a key factor to maintain core competitive advantages. Thus, predicting personnel future performance is a significant research domain in human...     

增材制造用球形TiAl合金粉末制备工艺研究

以TiAl合金块为原料,利用水冷铜坩埚真空感应熔炼气雾化技术制粉,通过对导流系统和雾化器的优化改进,制备出氧含量低、细粉收率高的球形TiAl合金粉末。结果表明,将导热性好的石墨导流基座和耐冲刷的BN材质陶瓷导流内芯配合使用,既可以保证导流管加热,也可以有效阻止金属熔液的冲刷;螺旋喷管雾化器使雾化点下移,回流区位置远离导流管出口,解决了液柱反流的问题。螺旋分布管能够有效约束雾化气体,动能损失小,能够显著提高细粉收率达20%以上。实验制备的球形TiAl合金粉末流动性为27.7 [s·(50 g)?1],球形度＞90%,粉末氧增量小,适用于3D打印和注射成型工艺用粉。     

Theoretical and experimental analyses of Young's modulus and thermal expansion coefficient of the alumina-mullite system

Young's moduli (E) and thermal expansion coefficients (TECs) of the alumina–mullite–pore system (96.4–99.5% relative density) were measured for a wide mullite fraction range from 0 to 100 vol%. Both E and TEC values decreased at high mullite fractions. These properties were theoretically analyzed with four proposed model structures that were constructed by three-phase systems of mullite (or alumina) continuous phase 2–pore dispersed phase 1–alumina (or mullite) dispersed phase 3. The ratios of E(theoretical)/E(experimental) and TEC(theoretical)/TEC(experimental) were very close to unity, depending on the mullite fraction. That is, the measured E and TEC values are closely related to the change in the composite microstructure as a function of mullite fraction.     

Effect of YSZ-incorporated glass-based composite coating on oxidation behavior of K438G superalloy at 1000 °C

A glass-based composite coating incorporating YSZ particles was prepared by sintering on K438G superalloy substrates. The YSZ additions increased the cyclic oxidation resistance at 1000 °C, while the formation of zircon resulting from interfacial reactions between YSZ and the glass matrix worked reversely. Besides, the YSZ inclusions changed the crystallization behavior of the glass matrix, and only anorthite precipitated during cyclic oxidation. Due to the synergy of sand-blasting and sealing effect of the glass-based coating, the oxidation behavior of K438G was changed and a layer of alumina instead of chromia formed at the substrate/coating interface. Furthermore, a gahnite layer formed at the alumina/gahnite interface because of interfacial reactions between alumina and the glass matrix, leading to the formation of a bi-layered thermally grown oxide. Thus, the alumina layer was protected from the attack of the active glass matrix. Accordingly, the coated K438G superalloy exhibited satisfactory oxidation resistance at 1000 °C.     

Microstructure and mechanical properties of an asymmetric twin-roll cast AZ31 magnesium alloy strip

The microstructure along the thickness of a strip produced by asymmetric twin-roll casting was found to be significantly inhomogeneous. There were many banded structures with flow form near the upper surface of the strip, whereas a fine dendritic structure dominated near the lower surface of the strip. Precipitates of Mg₁₇Al₁₂ and Al₈Mn₅ were dispersively distributed throughout the as-cast strip. Recrystallization of the strip during homogenization first occurred in the banded structures. After rolling and annealing, the strip consisted of fine grains measuring approximately 5 μm in size. It was concluded that the shear strain caused by the difference in linear velocity between the surfaces of the upper and lower rolls resulted in the banded structures of the strip.     

Effect of consolidation and oxide dispersoid addition on phase formation and mechanical properties of WTi ODS alloy

WTi alloys are presently considered promising candidates for plasma facing components in advanced nuclear energy systems. The mechanically alloyed WTi model alloys consolidated by different techniques were investigated. The effect of different amounts of the dispersed oxide particles on characteristics and properties of the WTi materials was also discussed. The results show that a homogeneous fine grain structure without formation of Ti-rich oxides is obtained in the model alloy sintered by spark plasma sintering. The (W,Ti)C solid solution and α″-Ti martensite phase are also found in the alloy confirmed by TEM investigation, which can be contributed to the effect of the carbon contamination and cooling rate during the process. In this work, it is clear to demonstrate that the presence of different carbides and Ti phases plays an important role in determining hardness and elastic modulus of the materials. The microstructure homogeneity and mechanical properties of the alloys can be further improved by increasing numbers of oxide dispersoids.     

Impact of microwave sintering on dielectric properties of screen printed Ba0.6Sr0.4TiO3 thick films

The influence of 30 GHz microwave sintering compared to conventional sintering has been investigated on polycrystalline Ba_0.6Sr_0.4TiO₃ (BST60) thick films with respect to an application as tunable dielectrics. The BST thick films were prepared as metal–insulator–metal (MIM) capacitors on alumina substrates. The average grain size (440 nm) and the porosity (approx. 30%) of the sintered films are only little affected by the sintering method. However, permittivity, dielectric loss and tunability have been influenced substantially. The dielectric improvement by microwave sintering is interpreted in terms of an increased crystal quality (ξ_S) and/or a decrease of defect concentrations. It is assumed that microwave sintering preferably heats up parts of the film where an increased defect density exists and therefore causes a selective heating process. This may heal up charged defects, inhomogeneities, and structural defects.