Efficient design/simulation algorithms for simultaneous switching noise in leadframe packages

 Two new modeling and simulation approaches for Simultaneous Switching Noise (SSN) are described and compared to “brute force” simulation by SPICE. Both simulation accuracy and simulation run-time are considered. The two new approaches are: 1) the “effective inductance” method, in which an approximate, very efficient method of extracting an SSN L _eff  is utilized; and 2) the “macromodel” method, in which the complex inductance network responsible for SSN is represented by only a few dominant poles in the frequency domain and the time domain response is obtained by an efficient convolution algorithm. Both approaches are shown to be accurate and fast, but only the effective inductance algorithm is robust in numerical convergence. Received: 19 March 1997 / Accepted: 25 March 1997     

Improved Repeatability of Pulsed Field Magnetometry Measurements Through Peltier Effect Temperature Control of Measurement Coils

Pulsed Field Magnetometers (PFMs) offer a method for high speed full loop characterisation of hard magnetic materials. As there is no dependency on iron to close a circuit, the repeatability of the technique is good. By utilising Peltier effect techniques to control the temperature of the measurement coil systems employed in a Pulsed Field Magnetometer, the level of repeatability of measurements can be significantly improved.     

Mechanism analysis of gate-induced drain leakage in off-state n-MOSFET

An analytical expression for both band-to-band and band-trap-band indirect tunnelings is used to study the gate-induced drain leakage (GIDL) current of MOSFETs measured before and after hot-carrier stress. The voltage and temperature dependence of GIDL are characterized. Both results show that interface traps situated near the midgap participate in the conduction of GIDL, and band-trap-band indirect tunneling could be the major mechanism. This is further supported by the fact that the percentage increase in GIDL induced by hot-carrier stress is about the same as the corresponding increase in interface-trap density. On the other hand, under low-field conditions, trap-assisted Poole–Frenkle emission dominates over tunneling for temperatures even well below room temperature.     

Nanostructured PbO materials obtained in situ by spray solution technique for Li-ion batteries

This paper describes a systematic study of the effect of various spray pyrolysis parameters, such as temperature, solution concentration and solution flow rate on the morphology, crystallization process, crystal size, specific surface area and electrochemical performance of in situ prepared α-PbO spherically agglomerated nano-structured powders. Different analytical methods such as XRD, SEM, TEM, BET gas sorption specific surface area measurements and electrochemical tests were performed. Crystallites in the range of 20–120 nm and easily dispersed powders were reproducibly prepared by optimization of the spray conditions. An increase of the temperature from 600 to 800 °C was found to lead to a three times increase in the average crystal size, from 31 to 102 nm. An increase of concentration from 0.15 to 0.5 M dramatically suppresses the crystal size from 127 to 25 nm. The BET surface area of sprayed PbO powders is increased up to 6.6 m² g⁻¹. For such PbO powders applied as anode materials in Li-ion batteries, we have managed to retain a reversible capacity above 60 mAh g⁻¹ beyond 50 cycles.     

Modular finite state machines: Development and application to reconfigurable manufacturing cell controller generation

This paper presents a new framework developed for logic control of manufacturing systems based on finite state machines (FSMs) and a method to automatically generate the control logic for manufacturing cell controllers using this framework. The framework is modular; FSMs are encapsulated into modules with well-defined communication between them. Events in the finite state machines are of two types, triggers and responses, allowing FSMs to react to events and to force events to occur. The automatic generation method is based on a library of predefined modules. Its application to and implementation on a manufacturing testbed is described.     

Far-Infrared Reflection Spectra of Dielectric Ceramics for Microwave Applications

Far-infrared reflection spectra of dielectric ceramics, BaSm₂Ti₅O₁₄, BaTi₄O₉, and some pcrovskites such as Ba(Zn_1/3Nb_2/3)O₃, have been measured at room temperature using a Fourier transform infrared spectrometer in order to investigate the effect of the crystal structure on the dielectric properties. As for perovskites, Sr(Zn_1/3Nb_2/3)O₃ and Sr(Mg_1/3Nb_2/3)O₃, in which B site ions are ordered, were also measured. Reflectance data were analyzed by means of a factorized form of dielectric functions instead of the classical dispersion theory, and all of the spectra were well fitted. The values of dielectric constants and tan δ calculated from the reflectance data were in good agreement with resonant cavity measurements at 5 GHz. Furthermore, results of this study have shown that the main contribution to the microwave dielectric properties is caused by low-frequency optically active modes located at 50 to about 300 cm⁻¹, and for perovskite structures it is suggested that the ordering of B site ions is significant in obtaining low dielectric losses.     

Measurement of human red blood cell deformability using a single micropore on a thin Si3N4 film

The filtration method for the evaluation of the RBC deformability has been further refined to simulate the deformations encountered in the recticuloendothelial system (in particular the spleen), a recognized site of aged and sickled cells removal. The core of the developed measuring system is a very thin (0.4 micron thick) filter that consists of single micropore (diameters down to 1 micron) on a Si3N4 film which has been constructed using silicon microfabrication techniques. Individual RBC's deformability is quantified measuring the cell pore passage time. From one blood sample 200 passage times are analyzed by a computer, displaying mean and median values as deformability indexes, and class and cumulative histograms for studying the passage times distribution. In this paper the effectiveness of the developed system as a routine clinical evaluation tool is demonstrated by studying several factors that are known to affect the RBC deformability, such as temperature, addition of diamide and glutaraldehyde, and blood storage conditions. In addition, it is experimentally demonstrated that the human RBC can traverse a pore with a diameter as small as 1 micron when the pore length is very short, thus broadening the experimental conditions under which the RBC deformability (fluidity) can be studied.