The effect of particle size distribution on the microstructure and properties of Al2O3 ceramics formed by stereolithography

Stereolithography (SL) shows advantages for preparing alumina-based ceramics with complex structures. The effects of the particle size distribution, which strongly influence the sintering properties in ceramic SL, have not been systematically explored until now. Herein, the influence of the particle size distribution on SL-manufactured alumina ceramics was investigated, including bending strength at room temperature, post-sintering shrinkage, porosity, and microstructural morphology. Seven particle size distributions of alumina ceramics were studied (in μm/μm: 30/5, 20/3, 10/2, 5/2, 5/0.8, 3/0.5, and 2/0.3); a coarse:fine particle ratio of 6:4 was maintained. At the same sintering temperature, the degree of sintering was greater for finer particle sizes. The particle size distribution had a larger influence on flexural strength, porosity and shrinkage than sintering temperature when the particle size distribution difference reached 10-fold but was weaker for 10 μm/2 μm, 5 μm/2 μm and 5 μm/0.8 μm. The sintering shrinkage characteristics of cuboid samples with different particle sizes were studied. The use of coarse particles influenced the accuracy of small-scale samples. When the particle size was comparable to the sample width, such as 30 μm/5 μm and 5 mm, the width shrinkage was consistent with the height shrinkage. When the particle size was much smaller than the sample width, such as 2 μm/0.3 μm and 5 mm, the width shrinkage was consistent with the length shrinkage. The results of this study provide meaningful guidance for future research on applications of SL and precise control of alumina ceramics through particle gradation.     

Irradiation-induced large bubble formation and grain growth in super nano-grained ceramic

In this work, 0.5TRPO•0.5Gd₂Zr₂O₇ ceramic with an average grain size of only ∼15 nm was prepared by a high pressure (5 GPa/520 °C) sintering method. Phase evolutions and microstructure changes of the as-fabricated super nano and micron-grained ceramics under a high-dose displacement damage induced by 300 keV Kr²⁺ ions were investigated. The results show that the super nano-grained ceramic has low degree of amorphization, obvious grain growth (2–3 times in grain size) and big Kr bubbles (10–68 nm) formation after irradiation. The micron-grained ceramic was severely amorphized after irradiation and many microcracks were formed parallel to its surface. The formation mechanism of Kr bubbles in the super nano-grained ceramic is on account of grain boundary diffusion and migration induced by the accumulation of the injecting Kr ions and irradiation defects. Nevertheless, microcracks formed in the micron-grained sample are caused by the accumulation of Kr atoms.     

Remarkably enhanced energy storage properties of lead-free Ba0.53Sr0.47TiO3 thin films capacitors by optimizing bottom electrode thickness

The lead-free Ba_0.53Sr_0.47TiO₃ (BST) thin films buffered with La_0.67Sr_0.33MnO₃ (LSMO) bottom electrode of different thicknesses were fabricated by pulsed laser deposition method on a (001) SrTiO₃ substrate. It was found that the roughness of electrode decreases and substrate stress relaxes gradually with the increase of LSMO thickness, which is beneficial for weakening local high electric field and achieving higher E_b. Therefore, the recoverable energy density (W_rec) of BST films can be greatly improved up to 67.3 %, that is, from 30.6 J/cm³ for the LSMO thickness of 30 nm up to 51.2 J/cm³ for the LSMO thickness of 140 nm after optimizing the LSMO thickness. Furthermore, the thin film capacitor with a 140 nm LSMO bottom electrode shows an outstanding thermal stability from 20 °C to 160 °C and superior fatigue resistance after 10⁸ electrical cycles with only a slightly decrease of W_rec below 1.6 % and 3.7 %, respectively. Our work demonstrates that optimizing bottom electrodes thickness is a promising way for enhancing energy storage properties of thin-film capacitors.     

A zirconium-free glaze system for sanitary ceramics with SiO2-CaCO3-TiO2 composite opacifier containing anatase: Effect of interface combination among SiO2, CaCO3 and TiO2

TiO₂ is an ideal substitute to ZrSiO₄ ceramic opacifier, yet it is limited to application because of the undesirable yellowing resulting from rutile formation. Herein, the SiO₂-CaCO₃-TiO₂ composite opacifier (Si-Ca-Ti) was constructed. The glaze used Si-Ca-Ti presents a superior opacification performance than ZrSiO₄ opacified glaze without causing yellowing, showing L*, a*, b* values of 94.81, -0.67 and 3.23. By comparison, the glaze using SiO₂, CaCO₃, and TiO₂ mixture shows lower opacification and yellowish surface with L* and b* values of 92.99 and 5.36. It is revealed that there is a close interface bonding among SiO₂, CaCO₃ and TiO₂ in Si-Ca-Ti, which promotes their combination reaction to generate opacification phase titanite and inhibit rutile formation when sintering, resulting in the white surface and opacification improvement of the glaze. This study proposes a green and efficient strategy to achieve white and highly opacified glaze for sanitary ceramics, exhibiting good application prospect.     

咖啡渣活性炭的制备、表征及其对Cr(Ⅵ)的吸附机制研究

以碘吸附值为评价指标，活化时间、活化温度和浸渍比为影响因素，采用响应面法试验设计对磷酸活化法制备咖啡渣活性炭的工艺条件进行优化，并通过静态吸附试验研究了不同吸附时间、溶液pH值和吸附温度条件下，活性炭对水溶液中Cr（Ⅵ）吸附性能的影响，最后利用Langmuir、Freundlich吸附等温方程、准一级动力学方程、准二级动力学方程和颗粒内部扩散方程进行拟合。试验结果表明，制备咖啡渣活性炭的最佳工艺条件为活化时间1 h、活化温度498℃、浸渍比1.72；在此条件下活性炭得率为30.4%，碘吸附值为（799±16）mg/g，比表面积为1 006 m²/g，孔容为0.779 cm³/g、微孔孔容为0.051 cm³/g、平均孔径为3.088 nm。较低pH值和较高温度能够促进活性炭对Cr（Ⅵ）的吸附；Langmuir等温方程能够更好地描述活性炭对Cr（Ⅵ）的吸附效果；活性炭对Cr（Ⅵ）的吸附分3个阶段：快速吸附阶段、慢速吸附阶段和吸附平衡阶段，10 min内可完成吸附总量的79%，360 min内达到吸附平衡，该吸附过程符合准二级吸附动力学方程。分析表明咖啡渣活性炭对Cr（Ⅵ）的吸附主要为单分子层的化学吸附。     

析湿工况下翅片管式换热器表面粉尘沉积过程的数值模型

空调器采用翅片管式换热器作为蒸发器，在制冷工况下换热器表面发生析湿及粉尘沉积，导致性能衰减。建立湿翅片表面粉尘颗粒物沉积过程的数学模型，模拟冷凝水捕集颗粒物以及湿积灰层黏附颗粒物的过程。被冷凝水捕集的颗粒物数量等于运动轨迹与水表面轮廓会出现相交的入射颗粒物的数量；后续的入射颗粒物与湿积灰层碰撞时，部分入射颗粒物会发生沉积且部分被碰撞的已沉积湿颗粒物会发生移除，这两部分的颗粒物数量相减即为被湿积灰层黏附的颗粒物数量。模拟与实验结果的对比表明，预测的湿积灰层形状与实验照片的吻合度较好，预测的单位面积颗粒物沉积质量与91%的实验数据之间的误差在±20%之间，平均误差为11.8%。     

色织亚麻金线提花织物的研制与开发

文章论述了色织亚麻金线提花织物的特点,介绍了在生产实践中采用低张力络筒和低速度整经等工艺技术,开发出的产品滑爽、挺括、透气,立体感强,是一种良好的装饰和服装用纺织流行面料。     

MPEG-4流媒体技术及其实现方法

详细地介绍了一种基于MPEG-4压缩的嵌入式网络流媒体采集、传输和控制应用系统的设计与实现技术。该嵌入式平台采用203 MHz的ARM920T内核处理器S3C2410B,嵌入式操作系统采用Linux操作系统,用户可在这个系统平台上进行自主软件开发。视频采集模块采用TI公司的TVP5145,视频压缩芯片采用硬压缩W IS GO7007B进行处理,将Y:Cb:Cr格式的视频流转换为MPEG-4编码。     

Time-of-flight secondary ion mass spectrometry as a tool for studying segregation phenomena at nickel–YSZ interfaces

Through a study of Ni–YSZ interfaces it is shown that time-of-flight-secondary ion mass spectrometry (TOF-SIMS) is a powerful and convenient tool for the analysis of ultra thin layers of segregated material at the interfaces and on free surfaces. Two different types of Ni, “pure Ni” (99.995% Ni) and “impure Ni” (99.8% Ni) were investigated. The contact areas on the YSZ and areas outside the contacts were examined with XPS and TOF-SIMS. The impure nickel causes a relatively larger amount of impurities to accumulate at the contact area, e.g. oxides of Mn, Ti, Si and Na. Some impurities migrate to the area outside the contact area. Even though on a larger scale the impurities seem to be homogeneously distributed, detailed analyses in and outside the contact area show the presence of impurity particles, and that the surface species are inhomogeneously distributed amongst the different grains. The extremely low detection limit, the small probe depth, the image capability, and the ease of elemental identification make TOF-SIMS an obvious choice as an analytical tool for studying segregation phenomena at metal–ceramic interfaces such as Ni–YSZ interfaces. XPS, being a quantitative technique, was used as a complementary technique to TOF-SIMS, which is not directly a quantitative technique.     

Java多线程编程中数据安全的应用研究

通过分析Java多线程并发机制的基本特征,着重针对Java多线程程序中的数据安全问题作深入探讨研究．指出在利用Java多线程技术进行实际编程过程中容易出现的数据安全问题以及相应解决方法．并结合实例说明数据安全在Java多线程编程中的具体实现。