织物弹道贯穿性能分析计算

纤维织物增强复合材料由于轻质和高冲击损伤容限而在防弹装甲设计及制造中逐渐得到应用,如人体防弹衣和车辆防护装甲。但是尚无较好的方法直接计算复合材料防弹特性,其中困难在于复合材料弹道冲击过程中的应变率效应和冲击破坏机理至今没有被揭示。解决问题的第一步是建立复合材料增强相(即织物)防弹特性计算方法。提出基于纤维力学性质应变率效应的织物弹道冲击破坏分析模型,计算不同面密度织物靶体在弹道贯穿过程中的弹体剩余速度,由此反映靶体防弹特性。用本文中提出的简单算法预测的结果与实测结果在靶体厚度不大时极为接近,而且也有可能将其扩展到纤维织物增强复合材料防弹性质的计算。     

Preparation and characterization of cuprous iodide nanoparticles

A new technique for the preparation of CuI nanoparticles from CuSO₄ and KI ethanol solutions has been developed. Preparation conditions were optimized through a series of experiments. Under these conditions, the yield of CuI reached 95.39%. The product was characterized and the reaction kinetics was studied. The results show that the product takes a roughly spherical shape with an average particle size of less then 50 nm. The activation energy of the formation of CuI is found to be E _a = 0.58 × 10² kJ/mol, and the preexponential factor in the Arrhenius equation is k ₀ = 7.43 × 10¹⁶ mol/(l s). The text was submitted by the authors in English.     

基于Solidworks的零件建模的若干方法

介绍零件的Solidworks三维建模的几种方法。利用Solidworks的Toolbox插件构造常见的零件模型;利用Solidworks曲线插入功能构造草图,或利用二维图形设计软件进行草图绘制,然后输出到Solidworks中特征构造。     

Properties of flash hydrated and agglomerated particles of CFB fly ashes

The fly ash (high carbon content and high unreacted CaO) recirculation in CFB is a typical method to improve the carbon burnout efficiency and the calcium utilization ratio. While the effectiveness of it is limited by the resident time and the reactivity of the re-injected fly ash particles. In the present research, an improved fly ash recirculation method is suggested in which the CFB fly ash is mixed with water or the mixtures of additives (such as waste water of paper mill, cement, sodium silicate, and carbide slag) and water in a blender. Then, this mixture is re-injected into the combustion chamber of CFB by a sludge pump. Because the temperature in CFB is higher, the fly ash was flash hydrated. At the same time, it was dehydrated and agglomerated. The size of agglomerates is bigger than that of original particle and their attrition rate is lower. Therefore the resident time of agglomerates is much longer than that of fine fly ash particles. The absorption of SO₂ is higher than that of original particles, too. This results in high carbon burnout efficiency. The hydrated lime also improves the calcium utilization.     

Analysis of the high-frequency spectrum of acoustic emission signals and its relationship to the wear resistance of filled polytetrafluoroethylene

We have performed tribotechnical tests of carbonaceous filled polytetrafluoroethylene in a wide range of loads with the recording of acoustic emission signals. Based on a spectral analysis of the sequence of rms deviations of acoustic emission signals using a discrete Fourier transform, we have constructed a normalized energy spectrum. We show that the mass wear of the material can be determined from the power of the high-frequency component of the spectrum obtained.     

省的基本原理及省转移的个案分析

分析了省的存在原理和转移原则，并对省转移的实际应用进行了实例对比分析，总结了省道转移中前胸省造型设计的规律，进一步探讨了省在实际设计中的应用规则。     

图形控制器在中小型控制系统中的应用

从选型、设计、调试3个方面比较了中小型控制系统中采用的触摸屏加PLC方案和图形控制器方案的优缺点;以某工厂供粉控制系统为例,给出了一种采用图形控制器来代替触摸屏加PLC的控制方案。实际应用说明了该控制方案的可行性及优势。     

建筑供排水用聚丙烯管道(PP-R)特性简析

PP -R管道具有质轻、连接方便、良好耐热性和较小导热系数、耐腐蚀且管道阻力小等优点 ,属绿色产品 ,本文对施工过程中就PP -R管与混凝土的粘结不密、抗紫外性能差等问题提出了相应的处理措施     

分形及分维在单轴向三维编织复合材料拉伸实验中的应用

基于分形几何的计盒维数研究了三维编织复合材料拉伸实验的断裂样照,结果表明,该材料的断裂曲线具有统计自相似性,在不同的尺度范围内具有不同的空间分布格局;而计盒维数定量地表征了其尺度变化规律;准静态和低应变率加载条件下材料的分维数较大,表明其空间占据程度较大,曲线弯曲结构复杂,这是因为低应变率加载时材料内部结构断裂时间不同造成;而高应变率加载时,断裂曲线分维数较小,曲线空间占据小,弯曲结构比较简单,这是由高应变率加载时材料内部结构断裂时间差异缩小造成。