Delamination growth mechanisms in woven glass fiber reinforced polymer composites under Mode II fatigue loading at cryogenic temperatures

The purpose of this research is to characterize the cryogenic delamination growth behavior in woven glass fiber reinforced polymer (GFRP) composite laminates subjected to Mode II fatigue loading. Mode II fatigue delamination tests were performed at room temperature, liquid nitrogen temperature (77 K) and liquid helium temperature (4 K) using the four-point bend end-notched flexure (4ENF) test method, and the delamination growth rate data for the woven GFRP laminates were obtained. The energy release rate range was determined by the finite element method. Microscopic examinations of the specimen sections and fracture surfaces were also carried out. The present results are discussed to obtain an understanding of the fatigue delamination growth mechanisms in the woven GFRP laminates under Mode II loading at cryogenic temperatures.     

Enhanced photoluminescence properties of Cu-doped ZnO thin films deposited by simultaneous RF and DC magnetron sputtering

Copper (Cu)-doped ZnO thin films were grown on unheated glass substrates at various doping concentrations of Cu (0, 5.1, 6.2 and 7.5 at%) by simultaneous RF and DC magnetron sputtering technique. The influence of Cu atomic concentration on structural, electrical and optical properties of ZnO films was discussed in detail. Elemental composition from EDAX analysis confirmed the presence of Cu as a doping material in ZnO host lattice. XRD patterns show that the films were polycrystalline in nature with (002) as a predominant reflection of ZnO exhibited hexagonal wurtzite structure toward c-axis. From AFM analysis, films displayed needle-like shaped grains throughout the substrate surface. The electrical resistivity was found to be increased with increase of Cu content from 0 to 7.5 at%. Films have shown an average optical transmittance about 80% in the visible region and decreased optical band gap values from 3.2 to 3.01 eV with increasing of Cu doping content from 0 to 7.5 at% respectively. Furthermore, remarkably enhanced photoluminescence (PL) properties have been observed with prominent violet emission band corresponding to 3.06 eV (405 nm) in the visible region through the increase of Cu doping content in ZnO host lattice.     

Molecular beam epitaxy growth of peak wavelength-controlled InGaAs/AlGaAs quantum wells for 4.3-μm mid-wavelength infrared detection

InGaAs/AlGaAs multiple quantum wells used for 4.3 μm mid-wavelength infrared quantum well infrared detectors were grown by molecular beam epitaxy. In composition loss was observed and quantitatively studied by high-resolution X-ray diffraction technology. By this In composition loss effect, the energy band engineering on the photo-response wavelength is not easily achieved. A thin AlGaAs barrier grown at low temperature is used to suppress the In atom desorption, and this growth process was verified to be able to adjust the photo-response wavelength as designed by energy band engineering in the photocurrent spectrum.     

Densification of transparent yttrium aluminum garnet (YAG) by SPS processing

Nano-size YAG powder co-mixed with 0.25 wt.% LiF was used to fabricate transparent polycrystalline YAG specimens by means of the Spark Plasma Sintering (SPS) technique. The presence of the LiF additive in the initial nano-powder allows obtaining fully dense disc shaped (up to 4 mm thick) transparent specimens at the outcome of a 2 h treatment at 1300 °C. The presence of LiF plays a key role in the mass transport related effects during the densification of YAG to full density and also in the elimination of the residual carbon contamination, allowing reaching a level of optical transmittance close to the theoretical value.     

Preliminary study on the tribology of an organic-molecule-coated touch panel display surface

The use of touch panel displays has been increasing due to the popularity of tablet PCs and smart phones. In order to protect the touch panel surface from scratches, contaminants from fingerprints and skin oils and so on, anti-contamination coating is necessary.One of the ways to protect the surface is to cover it with a thin and dense organic molecular layer. At the present time, the primary requirement for the coating is fingerprint-resistance or easy removal of contaminants. An adsorbed molecular layer of PFPE-derivatives is currently used for this purpose, in order to reduce the surface energy of the surface. Since the current major concern of panel makers is anti-fingerprint performance, degradation of the molecular layer by both tribological and environmental conditions is a major issue for the development of the coatings.Given the current priorities, however, tribological research into such subjects as the touch feeling of the panel and the friction characteristic has not been conducted. The touch feeling and its relation to the operation are very important but very difficult to study because it is very hard to express the touch feeling numerically. As a preliminary study, several different coated surfaces were prepared and their friction coefficients were measured by rubbing with a finger or a steel or glass ball to clarify the tribological characteristics of the surface.An Si wafer and a glass plate were used in this study as models of the solid substrate of a display. They were coated with an adsorbed organic molecular layer of two PFPE-derivatives with different molecular structures named Type-F and Type-D or several reference molecular layers, such as OTS-SAM and FDTE-SAM. In addition to the tribological data, degradation by UV irradiation was also examined to compare the performance. The results are discussed from the tribological and chemical points of view.     

Viscosity variations of coal-oil slurry under high temperature and high pressure during heating process

Heating coal-oil slurry (COSL) is an important step in direct coal liquefaction. Some physical and chemical properties of COSL including its viscosity will change during heating. A rotary viscometer was self-designed to measure the viscosity of COSL under high pressure and temperature. Three kinds of coal, which are Yanzhou coal (middle rank and caking), Shenhua coal (low rank and non-caking) and Shengli coal (brown coal), were mixed with anthracene oil to prepare the COSL. The COSL from Yanzhou, Shenhua and Shengli at the same experimental conditions showed different viscosity variations under high hydrogen pressure during heating. Yanzhou COSL had a higher viscosity peak, while Shenhua COSL had two small viscosity peaks and in the case of Shengli COSL, no viscosity peak was present under a high hydrogen pressure during the whole heating process. The coal nature is the important factor of viscosity variations of COSL. The higher the coal rank, the more caking coal is present, and the more obvious the viscosity variations of the COSL are.     

Layered mixed-anion compounds: Epitaxial growth,active function exploration,and device application

Optoelectronic properties and device applications of layered mixed-anion compounds such as oxychalcogenide LaCuOCh (Ch = chalcogen) and oxypnictide LaT_MOPn (T_M = 3d transition metal, Pn = pnicogen) are reviewed. Several distinctive functions have been found in these materials based on our original material exploration concept. Fabrication of high-quality epitaxial films of LaCuOCh leads to clarifying the excellent electrical and optical properties such as high hole mobility of 8 cm²/(V s) and heavy hole doping at >10²¹ cm^?3 in LaCuOSe, and sharp and tunable-wavelength photoluminescence in the solid–solution systems in LaCuOCh. In addition, a room temperature operation of a light-emitting diode is demonstrated using LaCuOSe as a light-emitting layer. These results suggest that the layered oxychalcogenides have potential for light-emitting layers as well as transparent hole-injection layers in organic/inorganic light-emitting diodes. Furthermore, by extending the material system from the copper-based oxychalcogenides to isostructural compounds, transition metal-based oxypnictides LaT_MOP (T_M = Fe, Ni), we have found novel superconductors, LaFeOP and LaNiOP.     

The synthesis,electrochemical and theoretical nonlinear optical properties of push–pull chromophores for photorefractive composites

Four chromophores, of different dipole moment and polarizable anisotropy and which comprised conjugation bridges of both benzene and polyene with strong electron-donor and electron-acceptor groups, were characterized using ¹H NMR, FT-IR, UV–vis, and electrochemical analyses. The electric dipole moment (μ), polarizability (α) and the first hyperpolarizability (β) values of the chromophores were examined using computational methods. The contribution of orientational birefringence to total birefringence was estimated from the calculated molecular parameters of the chromophores; these parameters are important factors for predicting photorefractive efficiency.     

Mechanism of the photoelectromagnetic effect in two-dimensional systems in quantizing magnetic fields

A new mechanism of the photovoltaic effect in a terahertz frequency range is proposed that is capable of explaining the features of terahertz photocurrents observed previously in asymmetric InAs quantum wells and double GaAs quantum wells in an external tilted magnetic field. It is shown that, in the asymmetric semiconductor heterostructures occurring in a tilted magnetic field, an edge photocurrent is generated due to the absorption of radiation on the electron transitions between Landau levels. A new approach to the creation of highly sensitive terahertz photodetectors based on asymmetric semiconductor heterostructures is proposed.     

Molecular dynamics simulation studies on some topics of water molecules on hydrophobic surfaces

———————————— 1 Introduction Molecular dynamics simulations have been rec- ognized as one of the most popular tools in the study of the behavior of systems at the nanoscale. Why wa- ter is so special and recognized as life matrix [1] has long been discussed. And it is well known that hydro- phobic force is one of the most important interactions in biological systems.[2] This article will focus on two of the most often discussed problems: the nanobubbles and the water molecules perme…