全文获取类型
收费全文 | 191篇 |
免费 | 30篇 |
国内免费 | 12篇 |
专业分类
电工技术 | 3篇 |
综合类 | 13篇 |
化学工业 | 1篇 |
金属工艺 | 2篇 |
机械仪表 | 37篇 |
矿业工程 | 1篇 |
水利工程 | 1篇 |
武器工业 | 100篇 |
无线电 | 36篇 |
一般工业技术 | 17篇 |
冶金工业 | 3篇 |
自动化技术 | 19篇 |
出版年
2023年 | 1篇 |
2022年 | 11篇 |
2021年 | 7篇 |
2020年 | 4篇 |
2019年 | 12篇 |
2018年 | 4篇 |
2017年 | 11篇 |
2016年 | 24篇 |
2015年 | 16篇 |
2014年 | 14篇 |
2013年 | 13篇 |
2012年 | 32篇 |
2011年 | 14篇 |
2010年 | 17篇 |
2009年 | 19篇 |
2008年 | 6篇 |
2007年 | 15篇 |
2006年 | 7篇 |
2005年 | 3篇 |
2000年 | 1篇 |
1996年 | 1篇 |
1993年 | 1篇 |
排序方式: 共有233条查询结果,搜索用时 15 毫秒
1.
在制导炸弹半实物仿真试验中经常发现,同一发制导炸弹多次仿真的俯仰角差别较大,同一批次制导炸弹投弹试验的遥测俯仰角与仿真俯仰角差别也较大,但是俯仰角的收敛趋势均一致,实测脱靶量与仿真脱靶量都合格,且具有一致性。为了分析出现上述现象的原因,基于协方差分析描述函数法(CADFT),建立了制导炸弹半实物仿真系统的误差传播理论,计算了仿真姿态角和姿态角速度的误差。分析了仿真姿态角和姿态角速度的误差对仿真结果的影响。结果表明,在仿真系统各种误差中,气动力和气动力矩误差是主要误差,是引起仿真俯仰角差别的重要原因; 姿态角的动态验模方法不适用于制导炸弹仿真模型,而脱靶量的静态验模方法适用于制导炸弹仿真模型。 相似文献
2.
故障预测作为基于状态维修实现的关键,可以有效支持维修管理者的决策。参照国际标准化组织对故障预测的定义,划分故障预测过程,提出预测方法性能评估至少存在的两种方式,在分类和比较现有预测方法的基础上,明确预测方法的适用范围和限制条件,为工程预测系统的构建提供参考。 相似文献
3.
4.
To measure miss distance for antiaircraft projectile,a radial velocity identification and positioning method with a single radar is proposed.By analyzing the spatial resolution of multi-frequency ranging radar,the discrimination and testing model of this radar for multi-targets (projectile and target) is established to analyze the systematic error of antiaircraft miss distance.Then through the aerial target flight test and contrast test with optical test equipment,the validity of the measurement method is verified.This new method has the potential to be used in the measurement of antiaircraft projectile miss distance. 相似文献
5.
6.
红外系统的作用距离参数是表征红外系统成像性能的重要指标。目前,红外系统作用距离的计算方法有多种,但都有其各自的适用性和局限性,因此需要考虑不同条件下多种因素对作用距离的影响。本文基于探测能量、基于噪声等效温差(NETD)的和基于对比度的3种点目标探测的作用距离模型,发现在不同条件下应用的局限性。当观测目标为人时,基于NETD的模型计算作用距离为8.74 km,与外场实验数据更为接近。而当观测目标为飞机时,基于能量的模型计算作用距离为32.04 km,与外场实验数据更为接近。结果表明,针对不同特征的目标,选取适当的作用距离计算方法有助于提高系统作用距离估算的准确度。 相似文献
7.
构成区截测速装置的两台天幕靶响应时间一致性直接影响测速精度,在天幕靶校准过程中需准确测量该参数.设计了一种测量天幕靶响应时间一致性的检测电路,采用LED发光二极管模拟弹丸穿过光幕的过程,用测时仪分别测量驱动LED灯的信号与天幕靶输出之间的时间.经实际测试验证,响应时间和响应一致性的测量误差为0.5μs,设计的电路可用于测速天幕靶的检定. 相似文献
8.
本文着重介绍了假单脉冲体制在雷达上具体的实现方法,以及假单脉冲体制的原理和和差环信号的处理。 相似文献
9.
The influence of explosive charge thickness on the quality of explosive welding of dissimilar metals was in-vestigated.The lower limit law should be followed in the course of explosive welding.Three welding ex-periments of stainless steel (410S) and steel (Q345R) were carried out in three different kinds of explo-sive charge thicknesses, namely 15, 25 and 35 mm.Interfaces of morphology and mechanical properties of three samples were observed and tested.It was found that micro and small wavy bonding is mainly formed for charge thickness of 15 mm whose strength is the highest with minor deformation and few defects in the interface; small and middle wavy bonding are mainly formed for charge thickness of 25 mm whose strength is comparatively mediocre; big wavy bonding is mainly formed for charge thickness of 35 mm whose strength is the lowest.The cause of high bonding strength of the micro and small wavy interface was analyzed and verified on the basis of the results of Electron Probe Micro-Analyzer (EPMA) tests of three selected samples. 相似文献
10.