Stress concentration analysis of fibre-reinforced multilayered composites with pin-loaded holes

The problem of stress concentrations in the area of pin-loaded holes is of particular significance in the design of multilayered fibre-reinforced composite structures. For the purpose of simulating such problem zones in anisotropic multilayered composites, analytical methods offer decisive advantages since they, in comparison to numerical methods, allow weighting of influencing parameters and in this way permit a physical interpretation of complicated notch phenomena. At the Institut für Leichtbau und Kunststofftechnik (ILK) sophisticated analytical solution methods for the stress concentration problem in multilayered composites with pin-loaded holes were developed on the basis of layer-related solutions and have been confirmed in numerical calculations.     

Granular model of packet pair separation in Poissonian traffic

We introduce a theoretical model of packet pair separation based on a transient solution of the Takács integro-differential equation. We show that in addition to the parameters of the fluid approximation (physical bandwidth and the average cross traffic rate) a new parameter characterizing the granularity of the cross traffic is necessary. These three parameters determine the dynamics of the queue in the diffusive approximation and all important distributions and averages of the packet separation even in multi-hop scenarios (assuming independent cross traffic on different hops). The model describes correctly the data collected in simulations, laboratory and Internet experiments. The adjustable model parameters are the physical bandwidth, the available bandwidth and the weighted average of the packet size of the cross traffic. We show that an implementation of the theoretical results can be used to estimate such parameters in packet chirp type measurements and can be a good candidate for improved available bandwidth estimation.     

喷雾沉积快速凝固技术的发展与展望

喷雾沉积是制取大体积快凝材料的一种新工艺。本文综述了它的产生和发展，概述了其基本原理和过程控制。对该领域今后的发展动向，提出了一些新看法。     

采用奇异值分解设计广义系统的最优滤波器

本文讨论广义离散随机线性系统的状态估计问题，通过矩阵奇值分解，本文给出了一种设计降阶最优滤波器的实用方法，该方法同时还得到了动态系统和量测系统的干扰噪声的估计。     

基体改性对C/C复合材料性能影响的研究(一)

本文从C/C复合材料的基体入手,研究了基体沥青、焦炭中添加氧化物的工艺条件及其在复合材料中的作用.结果表明,添加氧化物对基体改性,不仅能提高C/C复合材料的高温抗氧化性,也能对其它性能带来很大影响.只要控制适当的工艺条件,就可以得到高性能的C/C复合材料.     

超高强度钢CF裂纹扩展的超载效应 Ⅰ．定量模型及预测

将Ｗｉｌｌｅｎｂｏｒｇ的超载残余应力场模型与裂尖形变动力学、裂尖表面析氢反应电化学动力学以及裂尖材料内部氢的扩散动力学和热力学相结合，建立了氢脆腐蚀疲劳裂纹扩展（ＣＦＣＧ）超载效应的定量描述模型，给出了超载对裂尖表面析氢电化学反应及裂尖氢扩展影响的一系列判据和表达式．用上述模型进行的预测表明，对于超高强度钢，当两次超载周次之间裂纹扩展长度ａｄ远小于超载塑性区尺寸ｒｐＯＬ与恒载塑性区尺寸ｒｐＣＬＡ之差，即ａｄ＜＜ｒｐＯＬ－ｒｐＣＬＡ时，ＣＦＣＧ会发生比空气疲劳还强烈的超载迟滞效应．而当ａｄ＞ｒｐＯＬ－ｒｐＣＬＡ时，可能会发生超载加速效应．这种预测在后文中由试验的宏观规律与断口特征得到充分验证．     

Growth and properties of hydrogen-free DLC films deposited by surface-wave-sustained plasma

Hydrogen-free diamond-like carbon (DLC) films were deposited by a new surface-wave-sustained plasma physical vapor deposition (SWP-PVD) system in various conditions. Electron density was measured by a Langmuir probe; the film thickness and hardness were characterized using a surface profilometer and a nanoindenter, respectively. Surface morphology was investigated using an atomic force microscope (AFM). It is found that the electron density and deposition rate increase following the increase in microwave power, target voltage, or gas pressure. The typical electron density and deposition rate are about 1.87 × 10¹¹–2.04 × 10¹² cm^− 3 and 1.61–14.32 nm/min respectively. AFM images indicate that the grain sizes of the films change as the experimental parameters vary. The optical constants, refractive index n and extinction coefficient k, were obtained using an optical ellipsometry. With the increase in microwave power from 150 to 270 W, the extinction coefficient of DLC films increases from 0.05 to 0.27 while the refractive index decreases from 2.31 to 2.11.     

高摩擦学性能碳／碳复合材料研制

探索了高摩热学性能碳／碳（Ｃ／Ｃ）复合材料的制备途径，设计出了高摩擦学性能Ｃ／Ｃ材料的组织模型，并按模型制备出了在碳纤维上分布着球状沉积碳组织的Ｃ／Ｃ材料，实验表明：这种Ｃ／Ｃ材料具有良好的摩擦磨损性能，刹车力矩和速度的关系曲线平稳，初始力矩峰值小，摩擦系数适中；磨损率小，摩擦面光滑；试样无分层、碎裂、掉块等失效情况。