LF6铝合金的超塑性／扩散连接组合工艺试验及理论研究EI

本文研究了ＬＦ６铝合金的超塑性／扩散连接组合工艺，用变形和再结晶的方法细化晶粒，成功地进行了ＳＰＦ／ＤＢ工艺试验，利用电子探针观察了扩散连接接头的界面微观区域，并从机理上分析了金属的超塑性／扩散连接两种工艺之间的内部联系及其金属学行为。     

由ZF—6玻璃片构成的磁光旋转器

所提出的磁光旋转器是由Ｖｅｒｄｅｔ常数小的普通ＺＦ－６小玻璃片和带有窄缝隙的小电磁铁组成，当电磁铁线圈的功耗为１０Ｗ时，可得到２１°的法拉第旋转。     

Homogenization of hardness distribution and distortion in high pressure gas quenching

Quenching with gases rather than oil or other liquid media has the advantages of reducing the risks concerning health and environment, while simultaneously homogenizing the quenching results and minimizing distortion due to a wide range of possible process parameter variations and the pure convective heat transfer. In this contribution, a coupled solution for increasing homogenization of quenching results within high pressure gas quenching will be presented. In the first stage, an experimental test facility was set up for flow investigations and in the second stage a numerical simulation model was generated. The numerical and experimental results of the flow through the chamber were compared for several boundary conditions. Finally, after complete verification of the simulation, the model may be used to assist in parameter variation for optimization of homogeneous high pressure gas quenching.     

Measurement-related uncertainties in overcoring data at the Äspö HRL, Sweden. Part 2: Biaxial tests of CSIRO HI overcore samples

This paper is the second dealing with measurement-related uncertainties of overcoring data undertaken at the Äspö Hard Rock Laboratory and focuses on the biaxial test data from CSIRO HI overcore samples. The first paper dealt with measurement-related uncertainties in connection with the overcoring phase [1].The uncertainties identified in connection to biaxial tests of CSIRO HI overcore samples include too large applied pressures and poor sampling frequency. At the Äspö HRL, the results yield that most overcore samples fractured during biaxial testing, meaning that a significant part, 56%, of available strain gauge combinations were removed from calculations of the elastic parameters. Remaining strain gauge combinations indicate average values of 62±5 GPa for Young's modulus and 0.25±0.01 for Poisson's ratio, which are considerably lower than previously published values [2–5], and are in good agreement with results from biaxial tests on Borre Probe overcore samples [6–10]. The stress calculations were obtained from re-analyzed elastic parameters and strains, and show primarily a reduction in stress magnitudes. Overall, the stress field obtained with different stress measurement methods and its variation with depth is now quite well resolved. The overcoring data suggest that the principal stresses are inclined with a vertical component dipping about 65° from the horizontal over the investigated rock volume (140–420 m depth). This is interpreted as a result of influence from the sub-vertical NE-2 Fracture Zone that divides the stress data into two stress domains [11], although it may also be an artefact because the σ₂- and σ₃-magnitudes are of the same order of magnitude.     

Synthesis of polypropylene‐graft‐maleic anhydride compatibilizer and evaluation of nylon 6/polypropylene blend properties

Polymer blends based on polyolefins are of a great interest owing to their broad spectrum of properties and practical applications. However, because of poor compatibilities of components, most of these systems generally exhibit high interfacial tension, a low degree of dispersion and poor mechanical properties. It is generally accepted that polypropylene (PP) and nylon 6 (N6) are not compatible and that their blending results in poor materials. The compatibility can be improved by the addition of a compatibilizer, and in this study PP was functionalized by maleic anhydride (MAH) in the presence of an optimized amount of dicumyl peroxide (DCP). The reaction was carried out in the molten state using an internal mixer. Then, once the compatibilizer polypropylene‐graft‐maleic anhydride (PP‐g‐MAH) was prepared, it was added at various concentrations (2.5–10 wt%) to 30/70 glass fibre reinforced N6 (GFRN6) PP, and the mechanical properties were evaluated. It was found that the incorporation of the compatibilizer enhanced the tensile properties (tensile strength and modulus) as well as the Izod impact properties of the notched samples. This was attributed to better interfacial adhesion as evidenced by scanning electron microscopy (SEM). The optimum in these properties was achieved at a critical PP‐g‐MAH concentration. Copyright © 2005 Society of Chemical Industry     

Religious Participation, Interleukin-6, and Mortality in Older Adults.

This study prospectively examined the relationship between religious attendance, interleukin-6 (IL-6) levels, and mortality rates in a community-based sample of 557 older adults. Attending religious services more than once weekly was a significant predictor of lower subsequent 12-year mortality and elevated IL-6 levels (> 3.19 pg/mL), with a mortality ratio of .32 (95% confidence interval [CI] = 0.15,0.72; p     

智能化通信电源监控系统

以80C552单片机为核心,介绍了一种实现智能化电源监控系统的软、硬件设计。