丹江口工程大坝加高后的几个水力学问题

依托1∶100水工模型试验成果,重点介绍了丹江口大坝加高后的几个水力学问题如泄流能力、坝面压力特性、河床局部冲刷、下游河道流速流态、泄洪对电厂及航运的影响等.研究显示:大坝加高后泄流能力可满足设计要求,坝下河床冲刷加重,挑距加远,设计洪水22 300 m3/s时坝下冲坑最低点高程为43.0 m,各级泄量冲坑上游坡均缓于临界坡,也略缓于初期工程同级流量冲坑的上游坡;坝下600 m以内为护岸工程重点防护段,岸边流速为5.8～9.8 m/s;泄洪对丹江口电厂影响较小,对自备电站不利影响较为显著;最大通航流量6 200 m3/s时下游引航道口门区流态复杂,水流较混乱.     

台式毛细管放电X光激光装置调试实验

对自行研制的台式毛细管放电X光激光装置进行了系统调试,在充氩气毛细管负载下,输出电流38kA,电流脉冲前沿40ns,并对有关问题进行了讨论.并在这个装置上开展充氩气毛细管放电荧光光谱实验研究.     

非化学计量LaNi5型储氢合金的性能

采用富La混合稀土与Ni、Co、Mg等元素组合，获得了一种非化学计量LaNi5型储氢合金、用金相、XRD和SEM-EDX等方法分析了该合金的组织结构，研究了合金的气相储氢特性以及电化学性能，结果表明：在1.6MPa氢压和温度29℃下，该合金的储氢量达到1.58%（质量分数），该合金的放电容量为380mAh/g。经300次循环后容量保持率为55%，该合金的基体是CaCu5型结构的LaNi5相，但有第二相（LaMg)Ni3析出，这种第二相的形成是导致该合金大容量的关键。     

宜昌站泄流能力变化对葛洲坝设计洪水影响

宜昌水文站是葛洲坝、三峡水利枢纽的设计依据站。葛洲坝水利枢纽动工修建和运行 ,对该站水位流量关系中低水部分产生了影响。探讨了该河段泄流能力的变化对葛洲坝水利枢纽设计洪水有无影响的问题。用1 967～ 1 999年实测资料对宜昌站以汛期平均水位为参数的水位流量关系曲线簇进行了检验 ,大部分年份最大日平均流量、3、7、1 5、30d洪量的偏差在± 4 %之间 ,说明曲线簇推流具有相当的精度。证明了宜昌河段中低水泄流能力的变化对葛洲坝水利枢纽设计流量和校核流量基本没有影响     

检测GIS局部放电现象甚高频技术

文中介绍一种采用频率合成技术对GIS腔体内放电所产生的甚高频响应进行检测的UHF测量设备，该设备可接收到-110dBm以上的L波段放电信号，并已经通过实际测试。     

Modeling of the bulk free radical polymerization up to high conversion—three stage polymerization model. II. Number-average molecular weight and apparent initiator efficiency

The equations for predicting the number-average molecular weight are derived on the basis of the three stage polymerization model (TSPM) in this paper. By applying the equations, a plotting approach is proposed to determine the apparent initiator efficiency defined as f[(α_td+1)/2] and the constant of chain transfer to monomer, where f is the initiator efficiency and α_td denotes the fraction of the termination rate constants by disproportionation. Using the approach to plot the experimental data in the literature, it is found that the chain transfer to monomer can be neglected for both methylmethacrylate (MMA) and styrene (St) polymerizations, but it can exert a significant effect on ethylmethacrylate (EMA) polymerization. In addition, the apparent initiator efficiency is found to be independent of reaction temperature and initiator concentration at each stage. The values of f[(α_td+1)/2] at gel effect stage are slightly reduced as compared with that at low conversion stage for MMA and EMA polymerizations. However, it decreases significantly at gel effect stage for St polymerization. Using the equations derived and the apparent initiator efficiencies obtained from TSPM plots, the number-average molecular weights at different conversions can be predicted. Comparisons show that the agreement between predictions and experimental data is satisfactory.     

辽宁省节水工作存在问题及对策

辽宁省是水资源严重短缺的省份之一，水资源不足已成为制约全省经济社会可持续发展的瓶颈。通过对全省大型取用水户的调查分析，找出了辽宁省节水工作中存在的问题，提出了节约用水工作的对策和建议。     

Characterization of the flow behaviour of sausage emulsions with a simple tube viscometer

A specially designed tube viscometer was used to measure apparent viscosity during flow of Bologna type sausage emulsions moving through a pipe. Emulsions varied in fat content (from 21.8 to 44.3%) and in moisture/protein ratio (from 3.7 to 5.6), and the effects of added sodium chloride, sodium diphosphate, starch and blood plasma were investigated in a 36% fat, 3.7 moisture/protein emulsion.
The shear stresses determined as a function of shear rate were fitted by a power law. Yield stress of the emulsions was negligible relative to the applied stress. However, inspection of the flow profiles indicated that considerable slip of the sausage emulsion occurred at the pipe wall. Both emulsion flow and slip contribute to overall flow behaviour, so a kind of effective viscosity is determined. Intrinsic rheological properties and wall slip will both be affected by the composition of the sausage emulsion.     

Change of characteristics of desulfurization and denitrification by combustion flue gas composition and electrode configuration under pulsed corona discharge

Laboratory-scale and parametric experiments of SO₂ and NO_x removal from the simulated combustion gas by pulsed corona discharge have been performed by changing the combustion gas composition and temperature, the electrode configuration of plasma reactor, and the polarity of high-voltage electrode. The following results are obtained: 1) the higher the concentration of H₂O and O₂, the higher the efficiency of desulfurization and denitrification at the same specific input; 2) the pulsed corona discharge with a voltage pulsewidth as short as 200 ns of negative polarity shows the possibility to attain almost 90 percent deSO_x and deNO_x efficiency at the specific discharge input of 20 J/g, which is almost the same as the specific input in the electron-beam process; 3) the deNO_x characteristics show a little temperature dependence in the range of 70 to 130°C, but the deSO_x efficiency increases rapidly in the temperature region below 100°C suggesting the thermochemical dependence of deSO_x reaction; 4) when desulfurization and denitrification proceed, the white dendritic powder deposits on the plasma reactor whose composition is identified to be 49 mol% (NH₄)₂SO₄ and 47 mol% of 2NH₄NO₃ · (NH₄)₂SO₄, and the ratio of SO₂, NO and NH₃ of the deposit is almost equal to that of supplied gas.     

纯铜双层辉光离子渗钛组织形成机理及性能分析

采用双层辉光离子渗金属技术对纯铜进行了渗钛处理。用配有能谱仪(EDS)的扫描电子显微镜(SEM)、X射线衍射仪和透射电子显微镜对合金层的显微组织形貌、钛含量分布、相组成及相结构类型进行了观察与测定，对合金层的形成机理进行了探讨，并对其性能进行了对比测定。结果表明：渗钛层由合金层和扩散层组成，合金层主要由TiCu (Cu)固溶体 TiCu4构成，TiCu4为Dla型有序相，TiCu为B2型有序相，扩散层为(Cu)固溶体。渗钛处理后纯铜的表面得到显著强化。