三维叠前深度偏移处理技巧与应用

结合研究区的地质资料，着重就研究区的速度深度模型的人工控制进行了研究；基于研究区断裂系统复杂，为了解所用处理方法对复杂构造的适用性，设计了2个模型来检验叠前深度偏移效果的有效性；与时间偏移相比，叠前深度偏移高质量地解决了复杂断块区的成像问题。     

Acidity and basicity of hydrotalcite derived mixed Mg-Al oxides studied by test reaction of MBOH conversion and temperature programmed desorption of NH3 and CO2

Mg-Al hydrotalcites intercalated with five different interlayer anions—CO₃²⁻, SO₄²⁻, Cl⁻, HPO₄²⁻ or terephthalate—were synthesized by either the coprecipitation or ion-exchange method. The structure of the as-synthesized samples and the presence of intended anions in the interlayer gallery of hydrotalcites were determined by X-ray diffraction and FTIR spectroscopy. On calcination at 600 °C the materials were transformed into mixed metal oxides. The kind of the counterbalancing anions present in the parent hydrotalcite influences strongly textural parameters of the obtained Mg-Al oxides. Both temperature-programmed desorption of NH₃ and CO₂, and test reaction of 2-methyl-3-butyn-2-ol (MBOH) conversion were used to determine the acidity and basicity of the samples. The hydrotalcite derived mixed Mg-Al oxides showed the presence of Brønsted and Lewis acid and base sites. However, the strong basic character of the solids caused that acetone and acetylene were observed as the major products of MBOH conversion.     

The reaction of ceria coatings on mica with H2S: An in-situ X-ray diffraction study

Thin layers of ceria were deposited on the surface of mica platelets in solution. The reaction of such particles with hydrogen sulfide yields a red colored special effect pigment. The ceria layer reacts with H₂S to produce a variety of sulfide and oxysulfide phases. The reaction path discovered in situ by time and temperature resolved X-ray diffraction is CeO₂→CeS₂→C-Ce₂S₃→Ce₁₀S₁₄O. The reaction itself is extremely variable depending on gas flow, heating rates and decomposition atmospheres. Effects on the thin film are recorded by scanning electron microscopy (SEM) and revealed a destruction of the layer once red Ce₁₀S₁₄O was formed. The product layer then reveals the typical nonwetting behaviour of a liquid on a surface.     

Effects of Ca and Zr substitution upon structure and properties of Ba5LaTi3Ta7O30 low-loss dielectric ceramics

Effects of Ca and Zr substitution upon the dielectric properties of Ba₅LaTi₃Ta₇O₃₀ ceramics were investigated together with the structural characterization. All the samples of Ba₅La(Zr_xTi_1−x)₃Ta₇O₃₀ formed a filled tungsten-bronze structures, whereas the solid solution limit was determined as x=0.25 in (Ca_xBa_1−x)₅LaTi₃Ta₇O₃₀. Beyond this limit secondary phase of CaTa₂O₆ was detected and it would become the major phase for the Ca-rich compositions. The temperature coefficient of dielectric constant was improved with increasing Zr content while the dielectric constant decreased and the low dielectric loss varied little (in the order of 10⁻⁴). In the case of (Ca_xBa_1−x)₅LaTi₃Ta₇O₃₀, small temperature coefficient of dielectric constant could be obtained with increasing Ca content while the dielectric constant decreased significantly, and a small amount substitution of Ca for Ba induced decrease in dielectric loss.     

A comparative study of the gas sensing behavior of nanostructured nickel ferrite synthesized by hydrothermal and reverse micelle techniques

A comparative study of gas sensing behavior of nanocrystalline nickel ferrite synthesized by micro-emulsion and hydrothermal method to liquefied petroleum gas (LPG) is presented. Nanocrystalline nickel ferrite synthesized by hydrothermal method indicated higher electrical conductivity and gas sensitivity at low operating temperature compared to nanocrystalline nickel ferrite synthesized by reverse micelle technique. This difference in the gas sensing behavior can be attributed to the presence of more oxygen vacancies (i.e. non-stoichiometry) in the hydrothermally synthesized nickel ferrite. Incorporation of palladium had a catalytic effect and the operating temperature was significantly reduced in both the samples. The higher operating temperature of the reverse micelle nickel ferrite material makes the sensor response speed faster (∼10 s) compared to the hydrothermally synthesized material (∼1 min).     

Synthesis of LiFePO4 with fine particle by co-precipitation method

LiFePO₄ is a potential candidate for the cathode material of the lithium secondary batteries. A co-precipitation method was adopted to prepare LiFePO₄ because it is simple and cheap. Nitrogen gas was needed to prevent oxidation of Fe²⁺ in the aqueous solution. The co-precipitated precursor shows the high reactivity with the reductive gas, and the single phase of LiFePO₄ is successfully synthesized with the aid of carbon under less reductive conditions. LiFePO₄ fine powder prepared by co-precipitation method shows high rate capability, impressive specific capacity and cycle property.     

Effects of gallia additions on sintering behavior of gadolinia-doped ceria

The effects of gallia additions on the sintering behavior of gadolinia-doped ceria were systematically investigated from the following aspects: the variation in sintered density, the variation in grain size, and the existing forms of Ga₂O₃ in CeO₂.Sintered density increased with increasing Ga₂O₃ content up to 5 mol.% and then it decreased with further addition of Ga₂O₃. Grain size also increased with increasing Ga₂O₃ content up to 5 mol.% and then decreased with further addition of Ga₂O₃. Decrease in grain size was caused by a pinning effect of Ga₂O₃ precipitation at grain boundaries. Lattice constant decreased with increasing Ga₂O₃ content up to 5 mol.%. This decrease will be due to the substitution of smaller Ga³⁺ ions for Ce⁴⁺ ions in the CeO₂ structure. According to the results obtained from scanning electron microscope (SEM) and X-ray diffraction (XRD) analyses, the solubility limit of Ga₂O₃ in Ce_0.8Gd_0.2O_1.9 ceramics can be estimated to be nearly 5 mol.%. The addition of Ga₂O₃ up to the solubility limit was found to promote the sintering properties of Gd₂O₃-doped CeO₂.     

Electrical conductivity and gas sensitivity of Zn-Sb-O thick films

The thick film of Zn-Sb-O was prepared by coating the paste of nanoparticles mixture (Sb₂O₃:ZnO=1:3) on the alumina substrate, followed by sintering at 500-900 °C for 2 h in air. The electrical resistance and gas-sensing properties to benzene, alcohol and acetone of Zn-Sb-O films were found to be dependent on the change of phase structure caused by sintering temperature.     

Microwave assisted sintering of CaCu3Ti4O12

CaCu₃Ti₄O₁₂ electroceramic was prepared by a microwave assisted solid-state reaction technique from CaCO₃, CuO and TiO₂ powders. Processing involved the preparation of raw material, mixing and milling, calcination, pellet forming and sintering processes. Conventional furnace and microwave assisted sintering processes were employed in order to improve phase structures, morphology and dielectric properties of CaCu₃Ti₄O₁₂ ceramics. Surface and fracture FESEM analysis showed that the microwave assisted sintered CaCu₃Ti₄O₁₂ produced better densification and more uniform grain size compared to the conventional sintered sample.     

Potential of vibro-milling technique for preparation of electroceramic nanopowders

The potential of the vibro-milling technique as a simple method to obtain usable quantities of single-phase electroceramic powders with nanosized particles was examined. A detailed study considering the role of both milling time and firing condition on phase formation and particle size of the final product was performed. The calcination temperature for the formation of the desired phase was lower when longer milling times have been applied. More importantly, by employing an appropriate choice of the milling time and calcination condition, high purity electroceramic nanopowders have been successfully prepared with a simple solid-state reaction method.