Effects of structural parameters on water film properties of transpiring wall reactor

Corrosion and salt deposition problems severely restrict the industrialization of supercritical water oxidation. Transpiring wall reactor can effectively weaken these two problems by a protective water film. In this work, methanol was selected as organic matter, and the influences of vital structural parameters on water film properties and organic matter removal were studied via numerical simulation. The results indicate that higher than 99% of methanol conversion could be obtained and hardly affected by transpiration water layer, transpiring wall porosity and inner diameter. Increasing layer and porosity reduced reactor center temperature, but inner diameter's influence was lower relatively. Water film temperature reduced but coverage rate raised as layer, porosity, and inner diameter increased. Notably, the whole reactor was in supercritical state and coverage rate was only approximately 85% in the case of one layer. Increasing reactor length affected slightly the volume of the upper supercritical zone but enlarged the subcritical zone.     

Numerical investigation of a multichannel reactor for syngas production by methanol steam reforming at various operating conditions

A novel multichannel reactor with a bifurcation inlet manifold, a rectangular outlet manifold, and sixteen parallel minichannels with commercial CuO/ZnO/Al₂O₃ catalyst for methanol steam reforming was numerically investigated in this paper. A three-dimensional numerical model was established to study the heat and mass transfer characteristics as well as the chemical reaction rates. The numerical model adopted the triple rate kinetic model of methanol steam reforming which can accurately calculate the consumption and generation of each species in the reactor. The effects of steam to carbon molar ratio, weight hourly space velocity, operating temperature and catalyst layer thickness on the methanol steam reforming performance were evaluated and discussed. The distributions of temperature, velocity, species concentration, and reaction rates in the reactor were obtained and analyzed to explain the mechanisms of different effects. It is suggested that the operating temperature of 548 K, steam to carbon ratio of 1.3, and weight hourly space velocity of 0.67 h⁻¹ are recommended operating conditions for methanol steam reforming by the novel multichannel reactor with catalyst fully packed in the parallel minichannels.     

Catalytic Hydrocracking of a Bitumen‐Derived Asphaltene over NiMo/γ‐Al2O3 at Various Temperatures

Hydrocracking of a bitumen‐derived asphaltene over NiMo/γ‐Al₂O₃ was investigated in a microbatch reactor at varying temperatures. The molar kinetics of asphaltene cracking reaction was examined by fitting the experimental data. Below a defined temperature, the molar reaction showed the first‐order kinetic feature while at higher temperatures secondary reactions such as coke formation became significant, causing deviation of the reaction behavior from the proposed first‐order kinetic model. Selectivity analysis proved that dominant products varied from gases to liquids to gases with increasing temperature, shifting the dominant reaction from C–S bonds cleavage to C–C bonds cleavage.     

可调偏迈步式胶带自移机尾的研究

随着掘进工作面自动化程度的提高,掘进巷道速度也在日益加快,而现有的顺槽皮带机机尾移动缓慢且移动时工作量大,需要两三人配合操作,存在一定的安全隐患。针对以上问题,研发可调偏迈步式胶带自移机尾,具有与悬挂二运皮带转载机搭接行程长,可以迈步式前进,自动调偏等功能,同时,可以降低工人的劳动强度,加快巷道掘进速度。     

溶聚丁苯橡胶连续聚合工艺

概述了溶聚丁苯橡胶连续聚合工艺的凝胶抑制技术．指出连续聚合丁艺的重点是确定合适的抑凝体系；N，N，N＇，N’-四甲基乙烯基二胺／1，2-丁二烯以及四氢呋喃／1，2-丁二烯是最常用的抑凝体系。综述了单釜连续聚合和多釜串联连续聚合工艺．对世界各大橡胶公司的连续聚合反应釜的结构进行了介绍。     

林达大型低压甲醇合成塔在内蒙天野20万吨/年装置上的应用

简要介绍了林达均温型甲醇塔在内蒙天野20万t/a甲醇装置开车及初步运行情况。运行情况验证了该反应器的先进性,其催化剂床层测温点多、温度分布均匀、运行稳定。     

VRDS装置增加上流式反应器的技术分析

介绍了世界上第1套上流式反应器技术(UFR)在胜利炼油厂渣油加氢脱硫(VRDS)装置的生产运行情况。结果表明:UFR技术可以极大地优化VRDS装置的运转,减少装置运转的苛刻度,有效地延长装置运转周期,提高装置的经济效益。     

加氢反应器制造技术的新进展

随着加氢装置的大型化,对加氢反应器的设计、主体材质的选用及制造均提出了新的、更高的要求。文章较全面地介绍了国内外加氢反应器的设计准则、主体材质(抗氢钢)和制造技术等方面的新进展。