转底炉处理赤泥工艺技术

为了综合利用氧化铝冶炼产生的赤泥，探索在转底炉中直接还原赤泥、磨矿磁选获得高品位直接还原铁。通过实验室试验摸索了转底炉还原工艺参数，并在转底炉工业试验线进行了工业试验。实验室结果表明，赤泥还原后的直接还原铁(DRI)金属化率可达88.6%，磁选后的铁品位可达82.1%，磁选后的铁回收率可达88.9%。工业试验中，转底炉还原后，产品金属化率平均为69.2%，将还原后的DRI磁选获得高品位的DRI产品，磁选后DRI的铁品位为72.8%，磁选后铁回收率达到了85.2%,初步打通了在转底炉中还原赤泥、磁选的工艺路径。     

350MW机组锅炉SCR脱硝系统优化

准东煤田是我国目前最大的整装煤田,但准东煤在锅炉燃烧过程中易发生结焦问题,一般掺烧高岭土缓解结焦。某燃用准东煤350 MW机组,锅炉燃煤掺烧高岭土后烟气携带灰尘颗粒及灰尘量增大,出现SCR脱硝系统烟道积灰严重和喷氨量明显偏大问题,同时在空气预热器形成硫酸氢氨堵塞,使机组不能长周期稳定运行。通过与国内同类型多台机组锅炉对比后发现,脱硝系统均存在易产生积灰的脱硝转向室、催化剂上方及空气预热器入口斜坡积灰状况等情况。针对存在的问题,通过建立改造前、后的模型计算分析,进行了导流板布置的优化设计、CFD流场分布、优化SCR系统导流板设计、声波与蒸汽吹灰器结合吹灰和氨注射栅格优化升级等工作,应用德图480风速仪实测风速试验,发现脱硝烟道原导流板设计不合理及施工安装偏差;原导流板水平段跨距大,支撑不足,造成导流板压塌变形,影响烟气流场分布;锅炉所烧煤质为高钠煤,为防止锅炉结焦掺烧高岭土后,增加了烟气飞灰颗粒及灰尘量,飞灰具有很大黏性,易沉积在烟道导流板及烟道壁面上。因此,提出对脱硝内部各处导流板进行优化改造,对脱硝系统烟道易产生积灰的部位增加声波吹灰器,对喷氨格栅喷嘴数量及氨空混合器升级,同时开展锅炉SCR脱硝喷氨热态优化调整试验工作。通过开展相关工作,SCR烟气系统的烟气流场相对标准偏差优化5%,相同负荷下液氨消耗量降低45%,彻底解决脱硝系统积灰和空气预热器堵塞问题,实现机组满负荷达标稳定运行。锅炉长期运行半年后停炉检查,发现前期脱硝系统烟道高达1 m的积灰部位彻底解决,催化剂表面干净无杂物,解决了脱硝系统积灰问题,同时配合提高空气预热器冷端综合温度的措施,彻底解决锅炉空气预热器堵塞问题。同时,经济效益显著,每年可以分别节约液氨费用70万元,节约风机电耗费用100万元,节约检修清理积灰及检修费用80万元,节约空气预热器冲洗治理费用20万元,综合节约费用270万元/a,达到预期效果实现机组长周期安全经济稳定运行。     

煤磨热风管道改造的效果

中联万基水泥有限公司4500t/d熟料生产线采用SCLW4-12×13.4第四代篦冷机,煤磨热风取风口和余热发电AQC热风取风口在篦冷机同一对称位置,煤磨与余热发电系统存在争风现象,开停煤磨对余热发电系统影响较大。通过从废气管道处开孔,加装管道和电动阀,与热风管道汇合通往煤磨沉降室,调整相应阀门开度,可以控制入煤磨烟气温度,这样不但提高了余热发电量,而且提高了煤磨产量,同时也降低了窑头排风机的负荷,降低了熟料生产电耗。     

Crystal-field engineering of ultrabroadband mid-infrared emission in Co2+-doped nano-chalcogenide glass composites

Tunable and ultrabroadband mid-infrared (MIR) emissions in the range of 2.5–4.5 μm are firstly reported from Co²⁺-doped nano-chalcogenide (ChG) glass composites. The composites embedded with a variety of binary (ZnS, CdS, ZnSe) and ternary (ZnCdS, ZnSSe) ChG nanocrystals (NCs) can be readily obtained by a simple one-step thermal annealing method. They are highly transparent in the near- and mid-infrared wavelength region. Low-cost and commercially available Er³⁺-doped fiber lasers can be used as the excitation source. By crystal-field engineering of the embedded NCs through cation- or anion-substitution, the emission properties of Co²⁺ including its emission peak wavelength and bandwidth can be tailored in a broad spectral range. The phenomena can be accounted for by crystal-field theory. Such nano-ChG composites, perfectly filling the 3–4 μm spectral gap between the oscillations of Cr²⁺ and Fe²⁺ doped IIVI ChG crystals, may find important MIR photonic applications (e.g., gas sensing), or can be used directly as an efficient pump source for Fe²⁺: IIVI crystals which are suffering from lack of pump sources.     

A new mechanoluminescence phosphor Na3Sc2(PO4)3:Eu2+: Phase transition-assisted defect formation in a polymorphic composition

A new mechanoluminescent phosphor was developed from a sodium (Na) superionic conductor (NASICON)-structured Na₃Sc₂(PO₄)₃:Eu²⁺ phosphor that is known for its self-healing properties. The compound that crystalized assuming monoclinic C2/c symmetry was found to be blue-emitting, with no noticeable persistent luminescence. Thermoluminescence analysis showed that the phosphor had two prominent distinct thermal emission bands corresponding to the high-temperature β- and γ-phases of the composition. The mechanoluminescence properties of the material that does not have any persistent luminescence at room temperature were investigated by imparting impulsive strain. The compound on charging with 365 nm radiation was found to have significant mechanoluminescent emission originating from shallow defects present in the β-phase of composition that formed by the stress-induced phase transition process. Its emission characteristics and temporal behavior were investigated by varying the impact velocity.     

Correlation between instrumental texture and colour quality attributes with sensory analysis of selected cheeses as affected by fat contents

This study evaluated several physical and sensory parameters of different types of cheese available in the Polish market. The measurements of textural properties were conducted in an Instron universal testing machine, while the colour properties of cheeses were measured using a Minolta chromameter. The chemical composition was determined by means of the near‐infrared spectroscopy (NIRs). Moreover, a trained sensory panel was invited to assess the cheese texture‐related properties. Generally, cheeses with reduced fat content were characterised by higher hardness, adhesiveness, cohesiveness and elasticity. Texture‐related parameters of cheese with canola oil were comparable to that of most of full‐fat cheeses. The correlation analysis between physical and sensory attributes related to cheese textural properties indicated the potential applications of TPA, shear and penetration tests (r = 0.766, r = 0.75 and r = 0.765, respectively) for the evaluation of sensory properties related to the hardness. Meanwhile, the elasticity of cheese obtained from sensory evaluation was strongly correlated with the elasticity determined from the shear test (r = 0.722) and moderately correlated with the elasticity from penetration test (r = 0.588), indicating a need to refine the method of penetration test. In addition, cheeses exhibited higher meltability during convection heating at 230 °C than microwave heating. The values of meltability for cheese with reduced fat content were lower than those of full‐fat cheese.     

Evolution of properties of parts during MIM and sintering of recycled oxide particles

Metal injection moulding (MIM) is an established process for high volume production of complex shaped metallic parts using commercially available feedstocks. The characteristics of parts after moulding, debinding, and sintering cannot be simply predictable from raw materials because the properties get altered with the process parameters and the corresponding levels of porosity during processing steps. In this study, physical properties, microstructure, and mechanical properties of the MIM parts have been characterised to understand the evolution of strength during various steps in MIM processing. Feedstocks with different binder loading show a considerable difference in physical as well as mechanical characteristics. During sintering of parts which have solid loading of grinding sludge, simultaneous in situ reduction and densification takes place, whereas only densification occurs in carbonyl iron parts. It is, therefore, possible to make complex shaped parts of different levels of porosity from downgraded shop floor metallic waste.     

Experimental and numerical study on compressive performance of perforated brick masonry after fire exposure

This paper discusses the compressive performance of perforated brick masonry after fire exposure. Compressive strength tests of the mortar, clay perforated brick, and perforated brick masonry specimens were performed in accordance with ISO834 fire tests of different durations. The temperature distribution of the masonry materials and specimens was simulated using the finite element software ABAQUS, with the thermal parameters of masonry materials recommended by European standard Eurocode 6 and related literature. The compressive strength reduction factors of mortar and clay perforated brick exposed to different fire durations were calculated via the layered method suggested by European standard Eurocode 1. In addition, the compressive strength reduction factors after cooldown were obtained from the experimental data of the masonry materials, and by considering further reductions in the compressive strength after cooling from high temperatures. Experimental data of the masonry specimens were compared with the numerical results obtained using the reduction factors proposed in this work. The comparison revealed an overall acceptable approximation. Thus, the method presented in this paper can be used to evaluate the residual capacity of masonry structures after fire.     

Investigation on the effect of EDM process variables and environments on acoustic emission signals

Abstract

The performance of electrical discharge machining (EDM) primarily depends on the spark quality generated in the inter-electrode gap (IEG) between the tool and workpiece. A method for obtaining accurate information about the spark gap is required to effectively monitor the EDM process. The rise and fall of thermal energy in the discharge zone at a rapid rate during the dielectric breakdown produces high-pressure shock waves. This work explores the suitability of using acoustic emission (AE) generated from these shock waves and the elastic AE waves released on the workpiece due to the induced stress to monitor the performance and spark gap in EDM. The information content of the AE signals acquired at various machining conditions was extracted using AE RMS, spectral energy and peak amplitude. These features were able to well discriminate the machining condition, tool material, workpiece material, flushing pressure, current density, the initial surface roughness of the tool. Additionally, the AE signal features had a good and consistent correlation with the performance parameters, including material removal rate, surface roughness (Ra and Rq) and tool wear. The findings lay the groundwork to develop an effective, non-intrusive in-situ AE-monitoring system for performance and IEG condition in EDM.     

铜基化合物的可见光催化研究进展

与传统贵金属光催化剂相比，铜基光催化剂具有价格低廉、绿色环保、反应条件温和、光催化活性可调节等优势，受到合成化学家们广泛关注。本文简述了铜基催化剂的光催化历史，回顾了近五年来铜基化合物在可见光催化领域的研究成果与进展，总结了铜基催化剂的独立光催化机理与协同光催化机理；简要阐述了铜催化剂在不同类型反应中的应用，重点讨论了铜(Ⅰ)催化剂在烯烃官能化、碳-碳偶联、碳-杂偶联、原位催化等反应中的应用研究，表明铜基化合物在光催化合成领域具有很大的应用潜力。对未来的研究工作进行了展望，指出拓展催化剂的反应适用性、探索催化剂的氧化还原能力、进一步开发催化剂在手性合成中的应用将是该领域的研究重点。