溶液浓差能驱动的逆电渗析反应器制氢实验研究

低品位热能制氢技术首先是将热能转换为溶液浓差能，然后通过逆电渗析（RED）反应器将溶液浓差能转换成氢能。为了验证RED反应器能将溶液浓差能转换为氢能，探索关键运行参数变化对能量转换过程的影响。设计了一个由40个膜对所构成的RED反应器，以NaCl水溶液为工作溶液，NaOH水溶液为电极液的制氢系统。通过改变浓/稀溶液入口浓度，溶液过膜流速以及输出电流来考察对RED反应器产氢率、制氢效率和能量转换效率的影响。实验结果发现，浓/稀溶液入口浓度，过膜流速变化均会影响RED反应器的输出电流。在外电路短接条件下，输出电流越大，反应器产氢率和制氢效率越高，但能量转换效率越低。     

{X,Y}-Cyclacene Graphs with Next Nearest Neighbor Interactions

Eigensolutions of {X( = C,B,N),Y( = C,B,N)}-cyclacene graphs with next nearest neighbor (nnn) interactions have been obtained in analytical forms by adapting n-fold rotational symmetry followed by two-fold rotational symmetry (or a plane of symmetry). Expressions of eigensolution indicate the subspectral relationship among such cyclacenes with an even number of hexagonal rings e.g., eigenvalues of {X,Y}-di-cyclacene are found in the eigenspectra of all such even cyclacenes. Total π-electron energies and highest occupied molecular orbital and lowest unoccupied molecular orbital (HOMO–LUMO) gaps are calculated using the analytical expressions obtained and are found to vary negligibly with the variation of nnn interactions in such cyclacenes. Total π-electron energy is found to increase due to increase in restriction intensity of nnn interactions, whereas the HOMO–LUMO gap of polyacenecs having the even number of hexagonal rings and with one electron at each site (atom) decreases with increase in the restriction intensity since such systems contain degenerate half-filled HOMO (bonding or nonbonding) that are much more vulnerable for perturbations imposed through nnn interactions.     

三种硫化氢吸收剂吸收效率对比及碘酸钾体系吸收条件优化研究

硫化氢具有腐蚀性与毒性，采用吸收剂吸收硫化氢气体是重要的脱硫处理方式。不同的吸收剂在吸收效率上存在较大差别。首先对比了三氯化铁体系、碘酸钾体系和碱性铁氰化钾体系三种不同硫化氢吸收剂的吸收效率。在此基础上重点优化了碘酸钾体系吸收条件参数，讨论了包含浓度、温度、pH、气体流量及时间等因素对硫化氢吸收效率的影响。并建立了四因素三水平正交试验研究较优吸收条件，得到正交试验优化吸收条件为：温度55℃，pH 6.01，硫化氢流量0.3 L·min^-1，吸收时间1 min，该条件下8%（质量）碘酸钾体系的三级吸收效率为51.56%。研究结果对硫化氢吸收处理提供了理论参考，也为间接电解法循环处理研究提供了支持。     

Feedforward control of the transverse strip profile in hot-dip galvanizing lines

Hot-dip galvanizing is a standard technology to produce coated steel strips. The primary objective of the galvanizing process is to establish a homogeneous zinc layer with a defined thickness. One condition to achieve this objective is a uniform transverse distance between the strip and the gas wiping dies, which blow off excessive liquid zinc. Therefore, a flat strip profile at the gas wiping dies is required. However, strips processed in such plants often exhibit residual curvatures which entail unknown flatness defects of the strip. Such flatness defects cause non-uniform air gaps and hence an inhomogeneous zinc coating thickness. Modern hot-dip galvanizing lines often use electromagnets to control the transverse strip profile near the gas wiping dies. Typically, the control algorithms ensure a flat strip profile at the electromagnets because the sensors for the transverse strip displacement are also located at this position and it is unfeasible to mount displacement sensors directly at the gas wiping dies. This brings along that in general a flatness defect remains at the gas wiping dies, which in turn entails a suboptimal coating.In this paper, a model-based method for a feedforward control of the strip profile at the position of the gas wiping dies is developed. This method is based on a plate model of the axially moving strip that takes into account the flatness defects in the strip. First, an estimator of the flatness defects is developed and validated for various test strips and settings of the plant. Using the validated mathematical model, a simulation study is performed to compare the state-of-the-art control approach (flat strip profile at the electromagnets) with the optimization-based feedforward controller (flat strip profile at the gas wiping dies) proposed in this paper. Moreover, the influence of the distance between the gas wiping dies and the electromagnets is investigated in detail.     

Optimal design of nonlinear model predictive controller based on new modified multitracker optimization algorithm

The controller design for the robotic manipulator faces different challenges such as the system's nonlinearities and the uncertainties of the parameters. Furthermore, the tracking of different linear and nonlinear trajectories represents a vital role by the manipulator. This paper suggests an optimal design for the nonlinear model predictive control (NLMPC) based on a new improved intelligent technique and it is named modified multitracker optimization algorithm (MMTOA). The proposed modification of the MTOA is carried out based on opposition-based learning (OBL) and quasi OBL approaches. This modification improves the exploration behavior of the MTOA to prevent it from becoming trapped in a local optimum. The proposed method is applied on the robotic manipulator to track different linear and nonlinear trajectories. The NLMPC parameters are tuned by the MMTOA rather than the trial and error method of the designer. The proposed NLMPC based on MMTOA is compared with the original MTOA, genetic algorithm, and cuckoo search algorithm in literature. The superiority and effectiveness of the proposed controller are confirmed to track different linear and nonlinear trajectories. Furthermore, the robustness of the proposed method is emphasized against the uncertainties of the parameters.     

Improved error performance for generalised spatial modulation with enhanced spectral efficiency

The existing analytical average bit error rate (ABER) expression of conventional generalised spatial modulation (CGSM) does not agree well with the Monte Carlo simulation results in the low signal‐to‐noise ratio (SNR) region. Hence, the first contribution of this paper is to derive a new and easy way to evaluate analytical ABER expression that improves the validation of the simulation results at low SNRs. Secondly, a novel system termed CGSM with enhanced spectral efficiency (CGSM‐ESE) is presented. This system is realised by applying a rotation angle to one of the two active transmit antennas. As a result, the overall spectral efficiency is increased by 1 bit/s/Hz when compared with the equivalent CGSM system. In order to validate the simulation results of CGSM‐ESE, the third contribution is to derive an analytical ABER expression. Finally, to improve the ABER performance of CGSM‐ESE, three link adaptation algorithms are developed. By assuming full knowledge of the channel at the receiver, the proposed algorithms select a subset of channel gain vector (CGV) pairs based on the Euclidean distance between all CGV pairs, CGV splitting, CGV amplitudes, or a combination of these.     

The efficiency of private and public schools in urban and rural areas: moving beyond the development goals

Data from the Young Lives study are used to evaluate the efficiency of education systems in four low and middle income countries: Ethiopia, India, Peru and Vietnam. A meta‐frontier variant of data envelopment analysis is used to assess the relative performance of each country's system, and, within each country, to evaluate the impact of public and private schooling, and of urban and rural location. Comparisons are drawn between the four countries; the results indicate that in no country does the educational system perform uniformly badly or well. Conditioning on the inputs available, rural areas are often indicative of higher levels of efficiency, thus suggesting a number of implications for policy.     

干扰条件下的“北斗”信号解扩重构DOA估计

在干扰条件下，卫星导航抗干扰波束形成算法往往需要卫星信号波达方向（Direction-of-Arrival，DOA）的先验信息。但当存在低信噪比信号或主动干扰源时，常规的DOA估计算法性能急剧下降甚至失效。针对此问题，提出了一种被干扰信号压制的低信噪比“北斗”信号的DOA估计算法。该算法首先通过对接收信号进行子空间投影抑制干扰信号，然后对抑制干扰后的信号进行解扩重构处理，最后通过多重信号分类算法完成对“北斗”信号的DOA估计。仿真结果表明，在干扰信号干信比80 dB条件下，“北斗”信号DOA估计误差在5°以内，为下一步进行波束形成计算提供了高精度的入射角信息。     

Quantifying co-creative writing experiences

Collaboration with artificial intelligence (AI) is a growing trend even in the field of creativity. This paper examines which quantitative metrics can be used to comparatively analyse human-computer co-creativity with children. To study this question, 24 schoolchildren of age 10–11 wrote a poem with three co-creative poetry writing processes: a human-computer, a human-human, and a human-human-computer process. The computational participant in the processes was an AI-based application called the Poetry Machine. The children were asked to evaluate their user experience with a 5-point Likert-type questionnaire after each writing process and a comparative questionnaire after finishing all processes. The metrics used in the evaluation were immediate fun, long-term enjoyment, creativity, self-expression, outcome satisfaction, ease of starting and finishing writing, quality of ideas and support from others, and ownership.

Significant differences were found in fun, long-term enjoyment, quality of ideas, support, and ownership. The high number of statistically relevant results was enabled by exposing all participants to all writing processes, and the comparative questionnaire. The human-human-computer process was evaluated the best in long-term enjoyment and the human-computer process the weakest in support and idea quality. Creativity and ease of finishing writing turned out to be outlining metrics for the co-creative processes.