Control of the particle microstructure during the synthesis of bulk-polymerized transparent methacrylate-acrylonitrile-butadiene-styrene resin

A series of methacrylate-acrylonitrile-butadiene-styrene (MABS) resins was prepared using bulk polymerization. The polarity of the continuous phase and the compatibility of two phases were changed by adjusting the methyl methacrylate (MMA) content, choosing values that were close to styrene-butadiene rubber solubility value. The possibility of controlling the microstructure of the MABS resin by changing the polarity of the components and the compatibility of two phases was assessed. The dynamic mechanical analysis shows that the compatibility of two phases varies with the MMA content. The morphological analysis shows that increasing MMA contents results in a gradual decrease in the sub-inclusion structure with a network skeleton of rubber particles, and that all the particles become solid rubber when the MMA content reaches 75%. The sub-inclusion structure reappears but does not have a network skeleton when the MMA content is 90%. The impact strength and morphological analysis indicate that the solid rubber particles and the sub-inclusion structure with a network skeleton provide excellent toughness, while the sub-inclusion structure without a network skeleton does not. In contrast, the transmittance of the ABS resin first increased and then decreased with increasing MMA content.     

钒掺杂二氧化钛光催化活性研究

二氧化钛凭借优异的光催化性能,越来越受到人们的广泛关注和重视。以钛酸四丁酯为原料,利用水解-水热-干燥/煅烧工艺制备得到未掺杂TiO₂光催化剂和掺钒TiO₂光催化剂,利用其对甲基橙溶液的降解率做了比较分析。结果表明,以钛酸四丁酯为原料,采用溶胶-凝胶法制备钒掺杂TiO₂光催化剂是可行的。制备V/TiO₂产品的最佳工艺条件：钒钛质量比为6∶100、水热温度为160 ℃、水热时间为12 h,120 ℃下干燥14 h。紫外光照射条件下,甲基橙光催化降解效率达到99.10%,降解时间小于45 min。     

南水北调中线工程受水区二期需调水量预测研究

2002年12月国务院批复了《南水北调工程总体规划》，明确中线工程分两期建设。目前，一期工程已经通水。近年来，随着社会经济的快速发展，受水区的人口、生产规模、节水水平、人们对环境的要求都发生了变化，因此有必要根据新的情况对受水区的用水需求重新预测。分析了城市化发展和城镇用水变化的新形势，依据流域、区域水资源规划成果，提出了中线二期工程受水区需调水量，并与《南水北调中线工程规划》提出的二期需调水量进行对比，以供各方参考。     

AP1000稳压器波动管竖直管段空气-水CCFL实验研究

使用竖直管代替波动管模型开展稳压器波动管竖直管段内空气-水两相逆流限制（CCFL）特性可视化实验研究。实验现象表明:竖直管与上容器接口处的局部CCFL决定了进入竖直管内的液相流量；竖直管内的局部CCFL决定了从竖直管流出的液相流量；两处局部CCFL均随空气流量的增大而增强。在较低气量情况，进入竖直管内的液相能够完全或大部分流出，竖直管内的局部CCFL较弱，上容器和竖直管接口处的局部CCFL在整体CCFL中占主导地位，整体CCFL程度随着上容器液位升高而略有增强。在高气量情况，从上容器进入竖直管的液相大部分或者完全被限制而不能向下流出，竖直管内的局部CCFL强烈，在整体CCFL中占主导地位，整体CCFL特性不受上容器液位变化的影响。通过实验数据拟合得到了新的稳压器竖直管CCFL模型。稳压器波动管CCFL数据和稳压器竖直管CCFL数据基本重合，表明波动管CCFL主要由CCFL-U决定。      

Sensor network design based on system-wide reliability criteria. Part I: Objectives

Reliability based criteria are quite popular for optimal sensor network design. We present a modified definition of system reliability for sensor network design for two applications: reliable estimation of variables in a steady state linear flow process, and reliable fault detection and diagnosis for any process. Unlike the weakest-link based definition of system reliability in the literature, the proposed definition considers the entire system and is consistent with the reliability concept used in classical reliability literature. For each application, dual approaches for defining system reliability are proposed, and their analogy with the reliability problem in the classical reliability literature is established. Using examples and stochastic simulations, the advantage of using the proposed system reliability in contrast to the existing definition is illustrated. Part II of this series of articles presents methods for efficient generation of the system reliability function and its use in optimization-based approaches for designing optimal sensor networks.     

基于词法特征的恶意域名快速检测算法

针对互联网中恶意域名攻击事件频发，现有域名检测方法实时性不强的问题，提出一种基于词法特征的恶意域名快速检测算法。该算法根据恶意域名的特点，首先将所有待测域名按照长度进行正则化处理后赋予权值；然后利用聚类算法将待测域名划分成多个小组，并利用改进的堆排序算法按照组内权值总和计算各域名小组优先级，根据优先级降序依次计算各域名小组中每一域名与黑名单上域名之间的编辑距离；最后依据编辑距离值快速判定恶意域名。算法运行结果表明，基于词法特征的恶意域名快速检测算法与单一使用域名语义和单一使用域名词法的恶意域名检测算法相比，准确率分别提高1.7%与2.5%，检测速率分别提高13.9%与6.8%，具有更高的准确率和实时性。     

Adaptive actuator failure compensation design for unknown chaotic multi‐input systems

In this paper, an adaptive control approach is designed for compensating the faults in the actuators of chaotic systems and maintaining the acceptable system stability. We propose a state‐feedback model reference adaptive control scheme for unknown chaotic multi‐input systems. Only the dimensions of the chaotic systems are required to be known. Based on Lyapunov stability theory, new adaptive control laws are synthesized to accommodate actuator failures and system nonlinearities. An illustrative example is studied. The simulation results show the effectiveness of the design method. Copyright © 2014 John Wiley & Sons, Ltd.     

冷轧平整机机前甩尾轧制工艺的开发与应用

本文介绍了柳钢冷轧板带厂1550 mm单机架平整机机前甩尾轧制的工艺。改进前轧制每卷钢卷生产效率低,钢卷成材率低,改进后生产效率、成材率明显提高,部分规格的钢卷能实现带尾剪切长度为零。     

A new wavelet based fault detection,classification and location in transmission lines

This paper deals with the application of wavelet transforms for the detection, classification and location of faults on transmission lines. A Global Positioning System clock is used to synchronize sampling of voltage and current signals at both the ends of the transmission line. The detail coefficients of current signals of both the ends are utilized to calculate fault indices. These fault indices are compared with threshold values to detect and classify the faults. Artificial Neural Networks are employed to locate the fault, which make use of approximate decompositions of the voltages and currents of local end. The proposed algorithm is tested successfully for different locations and types of faults.     

Slow strain rate technique for studying hydrogen induced cracking in 34CrMo4 high strength steel

Alloy hardened steels offer excellent combination of mechanical properties, hardenability and corrosion resistance. 34CrMo4 is a medium carbon, low alloy steel widely used due to a good combination of high-strength, toughness and wear resistance. However, this steel experiences hydrogen embrittlement (HE), a complex phenomenon depending on the composition and microstructure. This work estimates de loss of the mechanical properties caused by hydrogen in electrochemically H-charged specimens in absence of mechanical stress but also, at low strain rate and constant load. H-charging for 2 and 6 h induce YS losses of about 40% and 71% and UTS losses of 39% and 59%, respectively. The synergistic effect of the stress and the H-charging process leads to a higher loss, 91%, and a faster brittle fracture even though hydrogen content is similar to those firstly H-charged and then tested in air.