紫金山东南矿段成矿期次、阶段浅析

通过对紫金山东南矿段铜钼(金)矿床地质矿化特征分析,指出铜钼矿化带主要赋存于花岗闪长斑岩的内外接触带,处于似斑状花岗闪长斑岩的上部,金矿化带赋存在表生氧化带的英安玢岩、隐爆角砾岩中。经过对矿石的组构特征、矿物生成顺序等特征分析,将矿床的成矿演化过程分为斑岩热液期、高硫化浅成低温热液期、表生氧化期三个主要矿化期次,进一步将斑岩热液期分为黑云母-钾长石化阶段、石英-绢云母化阶段、碳酸盐化阶段三个阶段;高硫化浅成低温热液期分为地开石化阶段、明矾石化阶段、硅化阶段三个阶段。研究结果为进一步研究矿床成因提供了依据。     

Etching characteristics of thin SiON films using a liquefied perfluorocarbon precursor of C6F12O with a low global warming potential

Perfluorocarbon gas is widely used in the semiconductor industry. However, perfluorocarbon has a negative effect on the global environment owing to its high global warming potential (GWP) value. An alternative solution is essential. Therefore, we evaluated the possibility of replacing conventional perfluorocarbon etching gases such as CHF₃ with C₆F₁₂O, which has a low GWP and is in a liquid state at room temperature. In this study, silicon oxynitride (SiON) films were plasma-etched using inductively coupled CF₄ +C₆F₁₂O+O₂ mixed plasmas. Subsequently, the etching characteristics of the film, such as etching rate, etching profile, selectivity over Si, and photoresist, were investigated. A double Langmuir probe was used and optical emission spectroscopy was performed for plasma diagnostics. In addition, a contact angle goniometer and x-ray photoelectron spectroscope were used to confirm the change in the surface properties of the etched SiON film surface. Consequently, the etching characteristics of the C₆F₁₂O mixed plasma exhibited a lower etching rate, higher SiON/Si selectivity, lower plasma damage, and more vertical etched profiles than the conventional CHF₃ mixed plasma. In addition, the C₆F₁₂O gas can be recovered in the liquid state, thereby decreasing global warming. These results confirmed that the C₆F₁₂O precursor can sufficiently replace the conventional etching gas.     

基于差频检测技术的高速AD单粒子翻转评估方法研究

本文基于差频检测的原理，提出一种在高频动态输入模式下，对高速高精度模数转换器（AD）的抗单粒子翻转效应进行评估的测试方法，并以一款8位3 GSPS高速AD为测试对象，设计开发了一套高速AD单粒子翻转效应测试系统，对目标器件进行了重离子试验。通过对试验结果的图像和错误数据进行分析，评估参试器件的抗辐照性能参数，为抗辐照高速高精度AD的加固设计提供数据支撑。     

F-OFDM仿真系统设计与时频同步算法

针对新一代5G波形的F-OFDM技术开展了研究,通过把一个宽带分为若干个子带,对每个子带进行滤波处理以实现更好的通信效能。基于Simulink平台进行了F-OFDM仿真系统的搭建,重点对F-OFDM符号同步方法和频偏估计方法进行了研究与仿真分析。实验结果表明,基于Chu序列相比采用PN序列可以获得更好的同步效果,基于导频的Classen频偏估计算法相比基于CP的CFO估计算法和基于训练序列的Moose估计方法可以获得更好的频偏估计效果。     

Optimized PI+ load–frequency controller using BWNN approach for an interconnected reheat power system with RFB and hydrogen electrolyser units

This paper investigates a renewable energy resource’s application to the Load–Frequency Control of interconnected power system. The Proportional-Integral (PI) controllers are replaced with Proportional-Integral Plus (PI+) controllers in a two area interconnected thermal power system without/with the fast acting energy storage devices and are designed based on Control Performance Standards (CPS) using conventional/Beta Wavelet Neural Network (BWNN) approaches. The energy storing devices Hydrogen generative Aqua Electroliser (HAE) with Fuel cell and Redox Flow Battery (RFB) are incorporated to the two area interconnected thermal power system to efficiently damp out the electromechanical oscillations in the power system because of their inherent efficient storage capacity in addition to the kinetic energy of the generator rotor, which can share the sudden changes in power requirements. The system was simulated and the frequency deviations in area 1 and area 2 and tie-line power deviations for 5% step- load disturbance in area 1 are obtained. The comparison of frequency deviations and tie-line power deviations of the two area interconnected thermal power system with HAE and RFB designed with BWNN controller reveals that the PI+ controller designed using BWNN approach is found to be superior than that of output response obtained using PI+ controller. Moreover the BWNN based PI+ controller exhibits a better transient and steady state response for the interconnected power system with Hydrogen generative Aqua Electroliser (AE) unit than that of the system with Redox Flow Battery (RFB) unit.     

Accounting for the uncertainties in the estimation of average shear wave velocity using V S– N correlations

Site-specific seismic hazard analysis is crucial for designing earthquake resistance structures, particularly in seismically active regions. Shear wave velocity ( V _S) is a key parameter in such analysis, although the economy and other factors restrict its direct field measurement in many cases. Various V _S–SPT– N correlations are routinely incorporated in seismic hazard analysis to estimate the value of V _S. However, many uncertainties question the reliability of these estimated V _S values. This paper comes up with a statistical approach to take care of such uncertainties involved in V _S calculations. The measured SPT– N values from all the critical boreholes were converted into statistical parameters and passed through various correlations to estimate V _S at different depths. The effect of different soil layers in the boreholes on the Vs estimation was also taken into account. Further, the average shear wave velocity of the top 30 m soil cover ( V _S30) is estimated after accounting for various epistemic and aleatoric uncertainties. The scattering nature of the V _S values estimated using different V _S– N correlations was reduced significantly with the application of the methodology. Study results further clearly demonstrated the potential of the approach to eliminate various uncertainties involved in the estimation of V _S30 using general and soil-specific correlations.     

胡萝卜丁中维生素C在热风辅助射频干燥过程中降解的动力学模型

目的研究热风辅助射频(hot air-assisted radio frequency,HA-RF)干燥过程中维生素C随温度变化的降解动力学模型。方法在6.5 cm极板间距和60℃热风系统条件下进行HA-RF干燥,重点研究胡萝卜丁中维生素C在干燥过程中的降解动力学,包括脱氢抗坏血酸(dehydroascorbic acid,DHAA)和抗坏血酸(ascorbic acid,AA)。总维生素C含量采用2,4-硝基苯肼分光光度法测定,AA采用2,6-二氯吲哚酚滴定法测定。结果HA-RF干燥过程中维生素C的降解规律符合一级可逆模型,其降解活化能为40.54 kJ/mol。DHAA活化能为35.83 kJ/mol,表明DHAA的稳定性低于AA。结论本研究使用的干燥温度为62.5~77.5℃,较高的干燥温度下维生素C降解速率较高,较低处理温度下的降解过程具有更好的模型适应度(R2>0.98)。     

Excellent destabilization effect and ideal desorption temperature in the hydride Mg2FeH6 substituted with yttrium; a first principles study

We investigated some properties of the hydride Mg₂FeH₆ substituted with yttrium by a first principles calculation. Some experimental results showed that 4d transition metal, yttrium serves as a good catalyst for magnesium based hydrogen storage alloys, but there are a few theoretical studies about magnesium based hydrides substituted with it. Mg₂FeH₆ is regarded as a cheaper material than pure MgH₂, while it is crystalized into Fm3m structure (space group 225). Although it has high hydrogen storage capacity, many investigations have not been devoted to it due to its extremely high thermodynamic stability. The yttrium substituted Mg₂FeH₆ exhibits very low energy of formation, and its desorption temperature, 75 °C is very suitable for practical hydrogen storage applications. Our results showed that Mg₂FeH₆ is destabilized effectively by yttrium substitution and introducing vacancy defects has additive effect to the improvement of dehydrogenation performance.     

刮板输送机中板仿生耐磨优化试验研究

刮板输送机中板磨损失效已成为输送机运行故障的主要原因之一，为了提高中板耐磨性，基于蜣螂非光滑单元进行了仿生中板设计，以磨损量为响应值，进行了单因素和响应面法优化试验。根据响应面法试验结果得到的因素显著性影响顺序（从高至低）依次为：径向距离，深径比，直径，节距角。基于试验结果建立了磨损量与因素的回归预测模型，经试验对比发现，预测模型与真实试验的相对误差为3.2%。在特定工况（煤散料粒度为6~8 mm、载荷为20 N、刮板链速为0.65 m/s及试验时长为6 600 s）下，当深径比为1.41、直径为0.69 mm、节距角为6.55°和径向距离为4.66 mm时，磨损量最小，仿生中板的耐磨性提高了12.6%。分析其耐磨机理发现，与光滑板相比，仿生板的磨粒磨损及黏着磨损较轻。凹坑分布可破坏持续切削中板表面的煤粒运动状态。中板的仿生优化可为今后刮板输送机的设计提供一定参考。     

Fundamental Evaluation of Power Supply and Rectifiers for Wireless Power Transfer Using Magnetic Resonant Coupling

This paper provides a fundamental analysis of a power supply and rectifiers for wireless power transfer using magnetic resonant coupling (MRC). MRC enables efficient wireless power transfer over middle‐range transfer distances. MRC for wireless power transfer should operate at a high frequency in the industry science medical band, such as 13.56 MHz, because the size of the transfer device decreases at higher transfer frequencies. Therefore, the output frequency of the power supply on the transmitting side should be 13.56 MHz. In addition, the rectifier on the receiving side is operated at a high frequency. This paper focuses on the reflected power in the power supply and rectifiers. Thus, the parametric design method is clarified for the power supply, including a low‐pass filter to match the output, the impedance of the power supply with the characteristic impedance of the transmission line. In addition, the effects on the rectifiers of silicon carbide and gallium nitride diodes are confirmed by performing an experiment and a loss analysis.