黄河下游河道萎缩致灾机理探讨

本文基于水力学原理，结合实体模型试验及原型实测资料分析，探讨了黄河下游河道萎缩的概念、致灾效应和致灾机理。分析表明，河道萎缩是造床过程中河道排洪输沙功能衰退的一种演变现象，其致灾效应是使洪水涨率增大，同流量下洪水水位不断抬升。致灾的现象主要表现在畸型河势增加、工程险情增多、直接造成工程损失及滩区经济损失等。试验研究揭示，主河槽宽度缩窄造成洪水水位涨幅增大，河底平均高程抬升和过水断面面积减小造成洪水水位起涨的基准面抬升是河道萎缩致灾的主要原因。河道萎缩致灾效应的大小与萎缩模式有关，其中以“集中淤槽”模式所形成的致灾效应尤为明显。     

Nanostructured polymer blends: Synthesis and structure

Nanostructured polymer blends prepared via anionic ring opening polymerizations of cyclic monomers in the presence of a pre-made polymer melt exhibit a number of special properties over traditional polymer blends and homopolymers. Here, we report on a simple and versatile method of in situ polymerization of macrocyclic carbonates in the presence of a maleic anhydride polypropylene (mPP) matrix and a surface-active compatibilizer (i.e. PC grafted onto a mPP backbone generated in situ) to yield a micro- and nanostructured polymer blends consisting of a polycarbonate (PC) minor phase, and a polypropylene (PP) major phase. By varying the processing conditions and concentration of the macrocyclic carbonate it was possible to reduce the size of the PC dispersions to an average minor diameter of 150 nm. NMR and TEM characterizations indicate that the PC dispersions do not influence crystal content in the PP phase. Overall, the results point to a simple strategy and versatile route to new polymeric materials with enhanced benefits.     

Assessing organo-clay dispersion in polymer layered silicate nanocomposites: A SAXS approach

A SAXS method for the quantitative assessment of the morphology of polymer layered silicate nanocomposites is proposed. Fitting the SAXS patterns, the number of clay layers, the periodicity of the layers in the tactoids, the thickness of the regions interposed between the clay platelets and their distributions can be measured. A good agreement with TEM data was obtained, avoiding the inconsistencies with microscopical observations often reported in the literature.     

Synthesis and characterization of a series of star-branched poly(ε-caprolactone)s with the variation in arm numbers and lengths

A series of star-branched poly(ε-caprolactone)s (SPCLs) was synthesized with structural variation of the arm numbers and lengths through ring-opening polymerization under bulk condition. Arm numbers were varied to be 3, 4, and 6 by using multifunctional initiating cores such as trimethylol propane, pentaerythritol, and dipentaerythritol, respectively. The lengths of the poly(ε-caprolactone) arms were varied by controlling the molar ratio of monomer-to-initiating hydroxyl group molar ratio ([CL]₀/[-OH]₀=5, 10, 15). Molecular weights were determined by both ¹H NMR end-group analysis and MALDI-TOF mass spectrometry, which gave reasonably consistent values. On the contrary, the GPC method failed to give accurate values of molecular weight of SPCLs due to the discrepancy with the linear standard. The branching architecture of SPCLs was evaluated by the branching ratio, g, which is the ratio of the mean-square radius of SPCL to that of liner counterpart, linear poly(ε-caprolactone) (LPCL), which is of the same chemistry and having the same molecular weight. The radii of gyration of SPCLs and LPCLs were determined using small-angle X-ray scattering (SAXS) from the initial slopes of Zimm plots, represented as 1/I(q) vs q² with I(q) and q being the scattered intensity and scattering vector, respectively. The g values were observed to decrease with increasing arm numbers, indicating more compact molecular structure for SPCLs with higher arm numbers, while no such effect was observed for arm length variation. Thermal properties as well as the degree of crystallinity of SPCLs were found to be also dependent on structural variations. The melting points and the degradation temperatures were observed to increase with increasing arm lengths but with constant arm number. On the other hand, arm number variation with constant arm length gave no such changes to the thermal transitions of SPCLs. However, for the SPCLs with equivalent molecular weights, the degree of crystallinity was found to decrease with increasing arm numbers.     

Potential tissue implants from the networks based on 1,5-dioxepan-2-one and ε-caprolactone

The synthesis and characterization of degradable polymeric networks for biomedical applications was performed. Cross-linked films of poly(ε-caprolactone) (PCL) and poly(1,5-dioxepan-2-one) (PDXO) having various mole fractions of monomers and different cross-link densities were successfully prepared using 2,2′-bis-(ε-caprolactone-4-yl) propane (BCP) as cross-linking agent. Reaction parameters were carefully examined to optimise the film-forming conditions. Networks obtained were elastomeric materials, easy to cast and remove from the mould. Effect of CL content and cross-link density on the final properties of the polymer network was evaluated. High CL content or degree of cross-linking led to increase in Young's modulus and decrease in elongation at break. An increase in crystalline domains in films having a higher CL content was observed by optical microscopy. A greater thermal stability was observed in films having a high CL content. The hydrophilicity of the materials could be tailored by changing the CL content. The surface of the films became rougher with higher CL content.     

A simple mathematical analysis on the effect of sand in Cr(VI) reduction using zero valent iron

A simple mathematical model was proposed to analyze the enhancement of Cr(VI) reduction when sand materials are added to the zero valent iron (ZVI). Natural decay of Cr(VI) in a control experiment was analyzed by using a zero-order decay reaction. Adsorption kinetics of Cr(VI) to sand was modeled as a first-order reversible process, and the reduction rate by ZVI was treated as a first-order reaction. Natural decay of Cr(VI) was also included in other experiments, i.e., the adsorption to sand, the reduction by ZVI, and both adsorption and reduction when sand and ZVI are present together. The model parameters were estimated by fitting the solution of each model to the corresponding experimental data. To observe the effect of sand addition to ZVI, both adsorption and reduction rate models were considered simultaneously including the natural decay. The solution of the combined model was fitted to the experimental data to determine the first-order adsorption and reduction rate constants when sand as well as ZVI is present. The first-order reduction rate constant in the presence of sand was about 35 times higher than that with ZVI only.     

Bi12TiO20 synthesized directly from bismuth (III) nitrate pentahydrate and titanium glycolate and its activity

Pure phase of sillenite structure, Bi₁₂TiO₂₀, was directly synthesized using stoichiometric bismuth (III) nitrate pentahydrate and titanium glycolate by co-precipitation. The influence of pH on the structure of Bi₁₂TiO₂₀ was studied in the pH range of 3–10. The sillenite structure was characterized using XRD and FTIR. The photo-degradation reaction of 4-nitrophenol (4-NP) was used to study photocatalytic activity of Bi₁₂TiO₂₀ as a function of the preparation pH. The rate of decomposition was followed by UV-vis and TOC. The beginning concentration of 4-NP, 44 ppm, decreased to less than 1 ppm within 30 min for all prepared catalysts. It was found that the decomposition rate constant of Bi₁₂TiO₂₀ is six times higher than those of either TiO₂ or Bi₂O₃ under the same conditions.     

Identification of photoluminescence features of an epoxy resin based on components features and curing effects

Photoluminescence features in a commercial grade cured DGEBA-based epoxy resin have been investigated with as objective to determine which of the material compounds are responsible for cured resin emissions. The origin of the bands has been approached by considering photoluminescence of base resin and hardener taken separately, of their mixture, and in the course of curing. Most of the bands observed in the cured resin could be interpreted based on those found in the components taken separately. Fluorescence of the cured resin appears dominated by two broad bands that are characteristic of the hardener and exhibits a blue shift by up to 30 nm in the course of curing which could be used for cure monitoring purpose of the investigated system. Fluorescence of the base resin is clearly detected in the resin cured with tertiary amine as catalyser. However, it is very weak if the catalyser is not added. Two phosphorescence processes have been isolated in the cured resin, one of them being related to the base resin. Finally, a chemiluminescence spectrum has been recorded in the course of curing, which has been related to either curing-related reactions or to an oxidation process.     

Generalized difference control of parallel streams temperatures

A furnace with multiple parallel passes and multiple burners is commonly seen in petroleum refineries. In order to maintain the furnace running in a safe, stable, and high-efficiency state it is necessary to control the outlet temperatures of the multiple passes to be the same. Due to the fact that the process of the oil heating in such furnace is nonlinear, multivariable, time varying, has serious coupling among passes, has frequent dynamic changes and a large time delay, traditional control methods have trouble in controlling these temperatures, and some advanced control methods, including predictive control, adaptive control, and robust control, are usually too complex for convenient use. In this paper, a control technique, called differences control technique (DsCT), is proposed to distribute the stream flowrates such that the stream temperatures are as identical as possible. The principle of the proposed technique is explained and demonstrated, and the results of its application to a real-life petroleum refinery furnace are also reported. The DsCT technique has the following advantages: it does not need complicated design procedures, the controller structure is simple, it is easy to apply, and it can be canonically applied to furnaces with different number of passes.     

Expressive Facial Gestures From Motion Capture Data

Human facial gestures often exhibit such natural stochastic variations as how often the eyes blink, how often the eyebrows and the nose twitch, and how the head moves while speaking. The stochastic movements of facial features are key ingredients for generating convincing facial expressions. Although such small variations have been simulated using noise functions in many graphics applications, modulating noise functions to match natural variations induced from the affective states and the personality of characters is difficult and not intuitive. We present a technique for generating subtle expressive facial gestures (facial expressions and head motion) semi‐automatically from motion capture data. Our approach is based on Markov random fields that are simulated in two levels. In the lower level, the coordinated movements of facial features are captured, parameterized, and transferred to synthetic faces using basis shapes. The upper level represents independent stochastic behavior of facial features. The experimental results show that our system generates expressive facial gestures synchronized with input speech.