Improved electrochemical redox performance of 2,5-dimercapto-1,3,4-thiadiazole by poly(3-methoxythiophene)

High electrocatalytic activity of an electropolymerized film of poly(3-methoxythiophene) (PMOT) is reported toward the redox reaction of 2,5-dimercapto-1,3,4-thiadiazole (DMcT) as a promising cathode material for the lithium ion battery. Cyclic voltammetry showed improved electrochemical performance of DMcT on PMOT-coated Pt electrode, indicating accelerated redox kinetics. Moreover, charge-discharge tests exhibited higher discharge capacity and slower capacity fading of the PMOT-doped DMcT composite cathode compared with pure DMcT.     

铅酸电池管式正极添加四碱式硫酸铅晶种的研究

在铅酸电池正极铅粉中加入一定量的四碱式硫酸铅（4BS）,按照工业化的操作工艺,制备出原料中4BS含量不同的正极板,并与常规负极板组装成小电池。对正极的初始容量和循环寿命等电化学性能做了测试,结果表明,在添加粒径为1.5 μm的4BS质量分数达1%时,65 ℃固化后,正极初始容量和循环寿命分别为未加4BS正极的1.02倍和1.06倍,4BS的加入提升了电池容量和电池寿命等的综合性能;XRD结果显示,原料中加4BS的正极中β-PbO₂含量稍高于未加4BS的正极;SEM结果显示,加4BS的正极活性物质更细小,大小更均匀。     

废电池的回收和处理

我国是电池生产和消费大国,废电池污染日益严重。介绍了废电池污染对人体造成的危害、国外主要废电池处理技术,分析了我国废电池回收处理的现状和存在的问题,并对我国废电池处理工作提出了建议。     

利用蓄电池废硫酸和硼泥制备高品质氢氧化镁

利用废铅酸蓄电池中的废硫酸作为浸取剂,对硼泥中的镁进行回收并制备出高品质的氢氧化镁产品。实验得出了酸浸硼泥的最佳工艺条件：酸浸温度为80℃;酸浸时间为30 min;酸用量为硫酸与硼泥质量比为1.2∶1。利用不同金属水解pH的不同,将酸浸过程中从硼泥和废硫酸中引入的杂质依次去除,得到精制硫酸镁溶液。由精制硫酸镁制取氢氧化镁的工艺条件为：常温下,沉淀剂为氨水,反应终点pH为11,反应时间为2 h,反应物在50℃下陈化12 h,过滤、洗涤后105℃烘干。实验考察了不同沉淀剂对氢氧化镁形貌的影响。所得氢氧化镁纯度在97%以上,粒径在0.1～1μm之间,各项指标均优于中国化工行业标准。     

锂离子电池正极材料研究进展

本文比较系统地叙述了用于锂离子电池正极材料的发展研究状况，其中包括的正极材料有：金属氧化物LiCoO2、LiNiO2、LiMn2O4、钒系正极材料以及有机多硫化物正极材料，并对正极材料研究的一些热点作了比较详细的评述。     

Mg~(2+)、Zr~(4+)离子掺杂对Li_4Ti_5O_(12)电化学性能的影响

以固相反应法合成了尖晶石型Li4Ti5O12电极材料,进行了金属离子掺杂以提高其导电性及综合性能,以适应用于大电流充放电的目的。采用XRD、室温恒流充放电循环、交流阻抗和循环伏安等测试手段,考察了A位掺杂Mg(Li4-xMgxTi5O12,x=0.15),B位掺杂Zr(Li4ZrxTi5-xO12,x=0.15)对Li4Ti5O12结构和电化学性能的影响。结果表明:掺杂少量的Mg2+、Zr4+未引起材料结构的变化,明显降低了Li4Ti5O12电荷转移阻抗,使导电性得到有效提高。0.1 C放电倍率下放电,未掺杂及掺杂Mg2+、Zr4+的Li4Ti5O12首次放电容量分别为159.8、144.9、161.2mAh/g,循环40次后,容量分别保持为113.8、130.6、133.6 mAh/g。与未掺杂的Li4Ti5O12相比,掺杂后的电极材料极化减小、循环容量及稳定性提高。     

Performance of a magnesium–lithium alloy as an anode for magnesium batteries

In this work, we describe an evaluation of an Mg–Li alloy (Li: 13 wt %) for possible use in magnesium primary reserve batteries. Higher OCP for the Mg–Li alloy have been observed in 2 M MgCl₂ and MgBr₂ electrolyte. The corrosion rate of the Mg–Li alloy is found to be in the order: MgCl₂ < Mg(COOCH₃)₂ < MgSO₄ < MgBr₂ < Mg(ClO₄)₂. Mg–Li alloys exhibit higher (81%) anodic efficiencies even when the current density is increased to 8.6 mA cm ^–2. It has been observed that Mg–Li/MgCl₂/CuO cells offer higher operating voltage and capacity than those with the conventionally used Mg–Al alloy.     

Polymer and nanobelt derived nanomaterials: opening doors to revolutionary stadia

ABSTRACT

The state-of-the-art article presents concepts of nanobelt nanofiller, inimitable properties of derived polymeric nanocomposite, applications, and outlook on challenges to gain next generation high-performance materials. Nanobelt is a one-dimensional nanostructured nanomaterial. Owing to minuscule size and high surface area, nanobelt possesses unique structural, optical, electronic, mechanical, and thermal characteristics. Nanobelt exists in various forms such as carbon nanobelt, polymer nanobelt, and inorganic. These nanobelts have been used to develop polymer/nanobelt nanocomposites. Homogeneous dispersion of nanobelt in polymer matrices is desirable to enhance the characteristics of polymer/nanobelt nanocomposite. Consequently, innovations in design, fabrication, and properties of various polymer/nanobelt nanocomposite are summarized. Applications of polymer/nanobelt nanocomposite are reviewed for Li-ion battery, supercapacitor, sensor, membrane, and biomedical arenas.     

离网型太阳能光伏发电系统设计研究

离网型太阳能光伏发电系统是太阳能光伏发电系统的重要组成。它具有灵活度高、分布广、项目成本低等优点。本文主要对现有离网光伏发电系统设计过程进行分析。     

The effects of Ni and Li doping on the performance of lithium manganese oxide material for lithium secondary batteries

Layered Li_0.7[M_1/6Mn_5/6]O₂ (M=Li, Ni) was synthesized using a sol-gel method. P2-Na_0.7[M_1/6Mn_5/6]O₂ precursor was first synthesized by a sol-gel method, and then O2-Li_0.7[M_1/6Mn_5/6]O₂ was prepared by an ion exchange of Li for Na in P2-Na_0.7[M_1/6Mn_5/6]O₂ precursor. From charge/discharge curves, it was seen that Li_0.7[Li_1/6Mn_5/6]O₂ has two plateaus similar to those observed from a spinel structure, but Li_0.7[Ni_1/6Mn_5/6]O₂ holds a single plateau as observed from a typical layered structure. It was considered that Li_0.7[Li_1/6Mn_5/6]O₂ undergoes a phase transformation from layered to spinel structure during the charge/discharge cycle, but Li_0.7[Ni_1/6Mn_5/6]O₂ maintains O2-layered structure after the cycles. Li_0.7[Ni_1/6Mn_5/6]O₂ was higher in discharge capacity and retention rate than Li_0.7[Li_1/6Mn_5/6]O₂.