Comparison of mass transfer efficiency in horizontal rotating packed beds and rotating biological contactors

In this study, the mass transfer efficiencies of a novel horizontal rotating packed (h‐RPB) bed and the conventional disc‐type rotating biological contactor (RBC) were studied at four speeds and seven submergences. Pall rings of two different sizes (25, 38 mm), superintalox saddles and a wiremesh spiral bundle were used as packings in the h‐RPB. Volumetric gas–liquid mass transfer coefficients were determined by unsteady state absorption of atmospheric oxygen in de‐aerated water. Power consumption per unit liquid volume has been found for all geometries tested. The oxygen transfer efficiency values for the h‐RPB were found to be 2–5 kg kWh^?1 and for the disc RBC were found to be 1–2 kg kWh^?1. The performance of the h‐RPB was also compared with other gas–liquid contactors such as surface aerators. The study proves that the h‐RPB is a energy efficient alternative to conventional contactors. Copyright © 2005 Society of Chemical Industry     

Nutrient removal performance of an anaerobic–anoxic–aerobic process as a function of influent C/P ratio

The laboratory scale anaerobic–anoxic–aerobic (A²O) process fed with synthetic brewage wastewater was designed to investigate the effects of changing feed C/P ratio on the performance of biological nutrient removal (BNR) processes. In the experiment, the influent chemical oxygen demand (COD) concentration was kept at approximately 300 mg L^?1 while the total phosphorus concentration was varied to obtain the desired C/P ratio. Results showed that when the C/P ratio was lower than 32, phosphorus removal efficiency increased as C/P ratio increased linearly, while when the C/P ratio was higher than 32, the P removal efficiency was maintained at 90–98%, and effluent P concentration was lower than 0.5 mg L^?1. However, regardless of the C/P ratio, excellent COD removal (90% or higher) and good total nitrogen removal (75–84%) were maintained throughout the experiments. It was also found that very good linear correlation was obtained between COD uptake per unit P released in the anaerobic zone and C/P ratio. In addition, the P content in the wasted activated sludge increased with the decrease in the C/P ratio. Based on the results, it was recommended that the wastewater C/P ratio and its effects be incorporated into BNR design and operational procedures, appropriate C/P ratios were used to achieve the effluent treatment goals. Copyright © 2005 Society of Chemical Industry     

调幅系数为任意值的调幅波研究

本文讨论了调幅系数为任意值的调幅波，给出了它的表达式，频谱与调幅系数，调制效率和信噪比增益的计算公式。     

安徽省长江干堤的几种加固措施

安徽省境内765km的长江干堤，由于均是在原来旧堤的基础上经逐年加高培厚的，修筑时均未按设计要求施工，致使堤身密实度不够，新老堤土之间结合不牢，在汛期高水位时易产生渗漏。20世纪70年代以来，安徽省高度重视对长江干堤渗漏隐患的处理，经过长期的实践，逐渐摸索出一套行之有效的除险加固方法，如锥探灌浆、灭杀白蚁、冲抓套吉、垂直铺塑防渗、粘土铺盖及压渗盖重等处理措施。使长江干堤的渗漏隐患得以基本消除，其具体作法可供类似工程借鉴。     

巯基棉预浓集—中子活化法测定水泥及其浸出水中的微量汞

在不同酸度下巯基棉可以从溶液中富集和分离Au、As、Ag、Br、Cu、Ca Co、InHg、Ni、Se、Sb、Sn、Pb、W、Fe和In等30多种元素。由于用巯基棉吸附待测元素后不必洗脱,因此大大提高了富集能力,可用于海水、地下水、地表水及工业废水中一些元素的测量。本文用巯基棉富集后进行中子活化分析测定水泥及其浸出水中的汞。     

CHA无机凝胶体系的研究及应用

过去低渗油藏调剖，注入性和堵塞性很难统一，新研制的CHA无机凝胶体系是一种易注入、堵塞能力强的调剖剂，而且成胶时间在一定范围内可控。研究了配比、温度对CHA无机凝胶体系成胶时间的影响，成胶前的注入性，成胶后在高温高盐条件下的堵塞能力，得到了可应用于现场的CHA无机凝胶体系。该调剖剂在濮城油田沙三段和文卫结合部等高温、高盐低渗油藏应用后，取得了很好的效果。     

晶体硅薄膜电池制备技术及研究现状

晶体硅薄膜太阳电池近些年来得到广泛的研究和初步的商业化探索。根据所采用的晶体硅薄膜沉积工艺中温度范围的不同，晶体硅薄膜电池研究可分为高温路线和低温路线两个不同发展方向。本文分别从这两个方向综述了目前国外晶体硅薄膜电池制备技术的最新进展，最新实验室研究结果。报导了晶体硅薄膜电池商业化进展状况，指出了晶体硅薄膜电池实现产业化必须解决的问题。     

UV法测定聚甲基丙烯酸酯纳米粒中胰岛素的包封率

建立一种简便易行的测定聚甲基丙烯酸酯胰岛素纳米粒中游离胰岛素含量方法.用Nanosep OD100C33超滤膜分离纳米粒和游离药物,在276 nm处测定药物的吸光度,建立胰岛素含量测定方法,并对线性、回收率、精密度等指标进行考察,最后测定各种胰岛素和载体比例混合的纳米粒的包封率.结果发现,该超滤膜能较好地分离纳米粒和游离的药物,在0.11～1.10 u/mL范围内,药物在276 nm的吸光度和浓度存在良好的线性关系(r=0.999 8),线性方程为A=0.868 8C-0.001 6,高、中、低3种浓度的回收率和精密度良好.该方法操作简单、结果可靠,可用于胰岛素纳米粒中药物包封率的测定.     

提高加热炉热效率措施的探讨

对本厂常减压装置提高加热炉热效率采取的措施进行了分析和总结     

Improvement of emission efficiency in polymer light-emitting devices based on phosphorescent polymers

We report improvement of emission efficiency in polymer light-emitting devices (PLEDs) employing phosphorescent polymers. A hole-blocking layer was inserted between the emissive layer and the cathode to enhance recombination efficiency for the injected holes and electrons. Aluminum(III)bis(2-methyl-8-quinolinato)4-phenylphenolato (BAlq) was used for the hole-blocking layer. The resultant PLEDs exhibited significant improvement of emission efficiency. The respective external quantum efficiencies for red, green and blue PLEDs were 6.6, 11 and 6.9%. These values are very high compared with those based on conventional fluorescent polymers.