Microstructure and Mechanical Properties of Heat-treated GeSb_2Te_4 Thin Films

The effect of annealing on microstructure,adhesive and frictional properties of GeSb 2 Te 4 films were experimentally studied.The GeSb 2 Te 4 films were prepared by radio frequency(RF)magnetron sputtering,and annealed at 200℃and 340℃under vacuum circumstance,respectively.The adhesion and friction experiments were mainly conducted with a lateral force microscope(LFM)for the GeSb 2 Te 4 thin films before and after annealing.Their morphology and phase structure were analyzed by using atomic force microscopy(AFM)and X-ray Diffraction(XRD)techniques,and the nanoindention was employed to evaluate their hardness values.Moreover,an electric force microscope(EFM)was used to measure the surface potential. It is found that the deposited GeSb 2 Te 4 thin film undergoes an amorphous-to-fcc and fcc-to-hex structure transition;the adhesion has a weaker dependence on the surface roughness,but a certain correlation with the surface potential of GeSb 2 Te 4 thin films.And the friction behavior of GeSb 2 Te 4 thin films follows their adhesion behavior under a lower applied load.However,such a relation is replaced by the mechanical behavior when the load is relatively higher.Moreover,the GeSb 2 Te 4 thin film annealed at 340℃presents a lubricative property.     

Microstructure and Its Influence on Mechanical Behaviour of Directionally Solidified DZ38G Superalloy

The features of microstructure and theirinfluence on mechanical properties onstress-rupture as well as thermal fatigue ofdirectionally solidified DZ38G nickel-base su-peralloy have been investigated.It has beenfound that the contents of carbides on grainboundaries are increased and morphology of γ'-precipitates has been changed after testing.Particularly γ'-precipitates coalesced intoraft-like in morphology perpendicular to theapplied stress-axis have been observed thathas no detrimental effect on the stress-rupturebehaviour.The tendency of σ-formation hasalso been discussed.The σ-phase can be avoidedwhen the process parameters are chosenappropriately during solidification.     

n-Al2O3P/Ni复合刷镀层的组织和摩擦磨损特性

研究了镍基纳米Al2O3复合电刷镀层（n-Al2O3^p/Ni）的组织特征及擦磨损特性，并与快镍刷镀（Ni)进行了比较。结果表明：n-Al2O3^p/Ni复合刷镀层表面粗糙度更小，组织更致密，镀层摩擦系数随镀液中纳米粒子含量增加稍有增大；n-Al2O3在复合刷镀层中弥散分布，与基相良好结合；复合镀的耐磨性能明显优于Ni刷镀层，镀液中n-Al2O3含量为20g/L时，复合刷镀层具有最佳耐磨性能。     

层状Ti3SiC2陶瓷的组织结构及力学性能

利用热压烧结TiH₂,Si和C粉获得了致密度大于98%的层状Ti₃SiC₂陶瓷。利用压痕法,在不同的载荷下测定了材料的维氏硬度, 发现其硬度值随载荷的增加而降低,在最大载荷30kg时,硬度值为4GPa。压痕对角线没有发现径向裂纹的出现。 这归因于多重能量吸收机制——颗粒的层裂、裂纹的扩展、颗粒的变形等。利用三点弯曲法和单边切口梁法测定了材料的强度和韧性分别为270MPa和6.8MPa·m1/2。Ti₃SiC₂材料的断口表现出明显的层状性质,大颗粒易于发生层裂和穿晶断裂,小颗粒易被拔出。当裂纹沿平行于Ti₃SiC₂基面的方向扩展造成颗粒的层裂,当裂纹沿垂直于基面的方向扩展时,裂纹穿过颗粒的同时,在颗粒内部发生偏转,使裂纹的扩展路径增加。裂纹的扩展路径类似人们根据仿生结构设计的层状复合材料。裂纹在颗粒内的多次偏转、裂纹钉扎以及颗粒的层裂和拔出等是材料韧性提高的主要原因。此外,在室温下得到的荷载-位移曲线,说明Ti₃SiC₂材料不象其它陶瓷材料的脆性断裂,而是具有金属一样的塑性。     

三峡水库蓄水前后长江上游近期水沙变化趋势

受多种因素影响,近年来长江上游来沙量明显减少,这将对三峡水库的效益产生影响。本文首先用实测年径流量和年输沙量双累积曲线统计分析法及Spearman秩次相关检验分析了三峡上游来水来沙减少的事实,并统计得到了近期来水来沙量的相关关系,该关系可用于预测近期三峡水库的入库年沙量。然后研究了上游大中小水库群拦沙淤积对减沙的影响系数,α相关分析结果表明α与水库下游沿程距离L呈指数函数关系。     

Dielectric, Ferroelectric and Piezoelectric Studies of PMN Modified PLZT Ceramics

Dielectric, ferroelectric and piezoelectric properties of xPb(Mg_1/3Nb_2/3)O₃-(1-x)(Pb_0.988 La_0.012)(Zr_0.535Ti_0.465)O₃ ceramic system synthesized through columbite precursor method are investigated. X-ray diffraction patterns of ceramics indicated pseudocubic phase formation with pyrochlore phase. Grain growth (4.47 μ m) and apparent density (7.68 gm/cm³) enhanced remarkably in 0.8PMN-0.2PLZT composition, respectively. Increasing PMN content remarkably increased both room temperature dielectric permittivity (ε_RT = 2316) and dielectric maximum (ε_Tc = 24747) in 0.6PMN-0.4PLZT composition, respectively. PMN substitution in PLZT system enhanced the ferroelectric remanent (P_r = 28.4 μ C/cm²) and spontaneous (P_s = 31.2 μ C/cm²) polarization while coercive field (E_c) continuously decreased in xPMN-(1-x)PLZT system. PMN modification in PLZT system influenced piezoelectric properties (d₃₃, k_p and k_t) throughout the PMN-PLZT system.     

Development of Low-Oxide MCrAlY Coatings for Gas Turbine Applications

Advanced high-energy plasma systems are being used to achieve the benefits of the high-velocity oxy-fuel (HVOF) system without losing the inherent advantages of plasma for coating of gas turbine parts. MCrAlY coatings play a very important role in the performance and reliability of gas turbine components. One of the important considerations for next generation of gas turbines, which have more demanding conditions and need to withstand ever increasing operating temperatures, is that they should possess very low oxygen content levels in the coating. Low oxygen content coatings are applied by the expensive low-pressure plasma spray (LPPS)/vacuum plasma spray (VPS) technique for critical components in aero- and land-based gas turbines. This work deals with the development of low-cost LPPS equivalent coatings (having low oxygen content) using the high-energy high-velocity plasma spray (HEHVPS) gun and inert gas shroud. A comparison has also been made with CoNiCrAlY coatings by HVOF.     

40Cr钢表面纳米层的微观结构

采用高能表面处理技术在40Cr钢表面制备出具有纳米晶体结构特征的表面层。利用透射电子显微镜和穆斯堡尔谱仪分析研究了表面纳米层的微观结构。结果表明，经过高能表面处理后，样品表面层晶粒细化为纳米晶，平均晶粒尺寸约为11nm。表面纳米层表面处渗碳体发生溶解。     

微型构造表征技术在八面河油田的应用

通过对八面河油田井网密集区及井网稀疏的欠开发区的微构造研究,探讨了微构造表征技术。首先在储层多层次逐级对比的基础上,建立主力油层对比关系;密集井网条件下,则利用钻井资料编制油层顶底微型构造图;对于欠开发地区,通过人机联作自动追踪成图技术,输出2m等值线间隔构造图,建立微构造模型。以微构造模型为基础进行潜力评价,部署关键井寻找优质储量或进行开发动态调整。应用该项技术在八面河油田滚动发现了角15块等断鼻翼部局部高点,增加石油地质储量488×10~4t。     

基于高抗热震性能的陶瓷刀具材料的微观结构设计

本文以现有的抗热震断裂和抗热震损伤的评价理论为基础，通过对材料中微裂纹的长度进行预测，从而实现了对陶瓷刀具材料的抗热震性能的微观结构设计。根据此理论对现有材料的抗热震性能的进行预测，预测结果与实际的测量结果相符，验证了该理论的正确性。