掺气减蚀保护作用的新概念

利用针式掺气流速仪测量原型和模型掺气浓度场、流速场，气泡尺寸及其概率分布的研究成果表明，原型水流韦伯数高，形成微小气泡的能力比模型强，气泡上浮慢，接近底部的小尺寸气泡概率及掺气浓度比模型大。初步研究认为：0.2mm或0.5mm以下的微小气泡在掺气减蚀中起着主要作用，可能只要很小掺气浓度即可达到掺气减蚀的效果。因此以小尺寸气泡的掺气浓度，作为判断掺气减蚀保护作用的指标将更为准确。     

Modeling of Material Deformation Kinetics in the Prefracture Zone

Based on the concept of complete stress–strain diagrams, we propose a new model describing the law of stress distribution in the prefracture zone in plastic materials in view of the type of the stressed state.     

Analysis of spontaneous electrochemical oscillations by energy distribution technique

Analysis of non-stationary electrochemical oscillations emerges utilization of the techniques allowing an observation of time evolution of their parameters such as instantaneous frequency, amplitude or frequency band. An algorithm of extraction of these parameters can be based on one of linear or quadratic time-frequency representations of oscillations record. In this paper, the authors present representatives of such transformations (Choi-Williams and Cone-shaped) originating from one of the most popular joint time-frequency energy distribution—Wigner-Ville distribution. Short introduction to the mathematics of the topic discussed is provided, then the authors present an example of application in the analysis of current oscillations of copper dissolution process.     

变形介质中宾汉稠油驱替特征

通过建立变形介质中考虑启动压力梯度的一维两相宾汉稠油驱替的数学模型,并进行了数值求解,分析了地层变形以及启动压力梯度对水驱稠油的影响,分析表明:介质变形对含水饱和度的分布没有影响,而对地层压力的影响是非常显著的,随着变形介质弹性的增加,地层压力越来越低,并且越靠近注入端,地层压力下降越快;原油的启动压力梯度同时影响含水饱和度和地层压力的分布,在其它条件一定时,启动压力梯度的存在,造成地层压力的增加和平均含水饱和度的降低。在油田开发实际中,应考虑地层变形和启动压力梯度的影响,以提高原油采收率。     

塔里木盆地雅—轮地区断层封堵性研究

塔里木盆地雅—轮地区大部分圈闭及油气藏的形成与断裂作用密切相关,对断层封堵性的综合研究已成为该地区油气勘探的重要因素。应用地质定性分析、Allen剖面分析及断层涂抹量计算等方法,通过对研究区4个典型断层封堵油气藏的系统解剖研究,建立雅—轮地区断裂封堵性评价标准,对雅—轮地区断层的封堵性进行综合评价。雅—轮地区断层整体封堵效果良好,断层在圈闭形成和油气聚集过程中起着重要的控制作用,形成一系列沿断层带状分布的油气藏。亚南断裂的封堵效果东部要优于西部,下部要优于上部。轮台断裂在不同部位、不同深度均存在着不同的封堵性能,封堵非均质性明显,总体显示断裂东部地区(也根附近)的封堵性要好于西部雅南地区。      

Characterization of the Residence Time Distribution in Spray Dryers

In this work it is presented a study on the residence time distribution (RTD) of particles in a co-current pilot-plant spray dryer operated with a rotary atomization system. A nuclear technique is applied to investigate the RTD responses of spray dryers. The methodology is based on the injection of a radioisotope tracer in the feed stream followed by the monitoring of its concentration at the outlet stream. The experiments were performed during the drying of aqueous suspensions of gadolinium oxide. The RTD responses obtained experimentally presented good reproducibility, indicating that the technique applied is well suited to investigating fluid-dynamics of spray dryers. In addition to the experimental investigation, a mathematical model was used to describe the RTD experimental curves.     

Chemische Zusammensetzung und Mikrostruktur polymerabgeleiteter Gläser und Keramiken im System Si–C–O. Teil 2: Charakterisierung der Gefügeausbildung mittels hochauflösender Durchstrahlungselektronenmikroskopie und Feinbereichsbeugung

Chemical Composition and Microstructure of Polymer‐Derived Glasses and Ceramics in the Si–C–O System. Part 2: Characterization of microstructure formation by means of high‐resolution transmission electron microscopy and selected area diffraction Liquid or solid silicone resins represent the economically most interesting class of organic precursors for the pyrolytic production of glass and ceramics materials on silicon basis. As dense, dimensionally stable components can be cost‐effectively achieved by admixing reactive filler powders, chemical composition and microstructure development of the polymer‐derived residues must be exactly known during thermal decomposition. Thus, in the present work, glasses and ceramics produced by pyrolysis of the model precursor polymethylsiloxane at temperatures from 525 to 1550 °C are investigated. In part 1, by means of analytical electron microscopy, the bonding state of silicon was determined on a nanometre scale and the phase separation of the metastable Si–C–O matrix into SiO₂, C and SiC was proved. The in‐situ crystallization could be considerably accelerated by adding fine‐grained powder of inert fillers, such as Al₂O₃ or SiC, which permits effective process control. In part 2, the microstructure is characterized by high‐resolution transmission electron microscopy and selected area diffraction. Turbostratic carbon and cubic β‐SiC precipitate as crystallization products. Theses phases are embedded in an amorphous matrix. Inert fillers reduce the crystallization temperature by several hundred °C. In this case, the polymer‐derived Si–C–O material acts as a binding agent between the powder particles. Reaction layer formation does not occur. On the investigated pyrolysis conditions, no crystallization of SiO₂ was observed.     

Sociotechnical systems, risk management, and public health: comparing the North Battleford and Walkerton outbreaks

Accidents in different complex sociotechnical systems are rarely compared using the same theoretical framework for risk management. We conducted a comparative analysis of two Canadian public health disasters involving drinking water distribution systems, the North Battleford Cryptosporidium parvum outbreak in April 2001 and the Walkerton E. coli outbreak in May 2000. Both accidents resulted from a complex interaction between all levels of a complex sociotechnical system. However, the low-level physical and individual factors differed in the two cases, whereas, the high-level governmental and regulatory factors tended to be the same. These findings may have implications for the design of public policies to minimize risk in complex sociotechnical systems.     

覆盖层厚度对巷道周围应力分布的影响及巷道间相互作用的仿真

给出了覆盖层厚度对巷道周围应力分布的影响及巷道间相互作用的计算机仿真，用三维有限元法分析了在不同覆盖层厚度下巷道周围的应力分布和两个巷道之间不同距离下的相互作用。数值模拟表明了巷道周围应力分布和应力集中系数随覆盖层厚度增加的变化规律，找到了两巷道之间的距离的临界值，当两巷道间距离大于该临界值时，它们之间的相互作用消失。     

THE STATISTICAL DISTRIBUTION OF EXTREME VALUES OF WAVE-CURRENT FORCES ACTING ON SLENDER CIRCULAR CYLINDER IN IRREGULAR WAVES

Based on model test,the statistical distribution of extreme values of wave-current in-line forces acting on vertical circular cylinder is analyzed in this paper.It is shownthat the results calculated by the simplified method,proposed by authors,agree well with the testdata;Weibull distribution is also adoptable in the region of high KC number, and the shapeparameter a and scale parameter β are related well with KC number respectively.