Niobium-containing catalysts—the state of the art

This review article is devoted to the materials containing niobium, which have been discovered or developed in the past few years and exhibit the potential application in heterogeneous catalysis. Niobium oxides and mixed oxides as well as sulfides, nitrides (oxynitrides), carbides (oxycarbides), and phosphates are considered. Among the catalytic processes in which Nb-containing materials were tested, liquid and gas phase oxidation is described in details, and the role of niobium in the prevention of the catalyst from SO₂ poisoning is mentioned.     

A new polymer electrolyte poly(acrylonitrile)-dimethylsulphoxide-salt for electrochemical capacitors

The PAN-DMSO-Et₄NBF₄ and PAN-DMSO-Et₄NTf (Tf is triflate ion) electrolytes were prepared as white, turbid foils with a thickness in the range of 0.1-0.5 mm, using the casting technique. Room temperature conductance of the electrolytes, detected from ac impedance experiments, was at the level of 8 and 14 mS cm⁻¹ for Et₄NBF₄ and Et₄NTf salts, respectively. The electrochemical stability window of approximately 2.6-2.8 V was estimated using a glassy carbon electrode. Temperature dependence of the conductivity is of the Arrhenius-type for both electrolytes, with an activation energy of approximately 34 kJ mol⁻¹. The double-layer capacitors built with these electrolytes, serving both as separators and activated carbon powder (ACP) binders, showed a specific capacity of 50 F g⁻¹ of carbon material. Capacitors were assembled by sandwiching the PAN-DMSO-salt electrolyte between two PAN-salt-DMSO-ACP-AB electrodes and pressing across the system; the resulting devices had a coin-like shape with 8 mm diameter and thickness between 2.0 and 2.5 mm.     

电磁发射兵器用电容器的选取

本文首先从理论上论述了膜电容器的储能密度与寿命之间的关系，对国际电容器制造水平和趋势进行了分析，提出采用干式金属化膜电容器作为储能元件。最后，根据电磁发射兵器整体寿命配合原则，提出高储能密度脉冲电容器的合理寿命指标。     

Monte Carlo simulation of gas phase polymerization of 1,3‐butadiene. Part II: Kinetics optimization and confirmation

Studies on the deactivations and initiations of gas phase polymerizations of 1,3‐butadiene have been achieved by Monte Carlo simulation. Initiation and deactivation control the reaction before and after the peak of the polymerization rate, respectively. The influence of polymerization temperature has been studied. Monte Carlo modeling of polymerization kinetics and mechanism was confirmed by the agreement of experimental data and simulation results of polymerizations run with a temporary evacuation of monomer. The balance of catalysts and active chains is established by both initiation and chain transfer reactions with cocatalyst, which causes a ‘pseudo‐stability’ stage. © 2003 Society of Chemical Industry     

包装件压力试验机计算机测控系统

针对YE-50包装件压力试验机落后的测控系统，提出一种基于压力和位移闭环控制的计算机测控系统。根据测得的压力、位移和设定值，通过模糊控制输出驱动伺服阀实现了压力试验时的恒速控制和堆码试验时的恒力控制。并实时显示力——位移及应力——应变曲线。文中还对模糊控制器的实验整定方法进行了探讨。     

基于MODBUS协议的激光雕刻切割系统HMI人机交互设备

近年来,国内激光雕刻切割控制器技术发展迅速,基于PC的传统控制器已相当成熟.为了显著提高工业生产效率,适应工业生产规模扩张的需要以及工业对系统稳定性要求的提高,目前国内几家专业运动控制器厂家已经实现了激光雕刻切割控制器的完全脱机运行.本文针对脱机控制器的需要设计一款人机交互设备,该设备采用AT89C55WD单片机为主控制器,采用标准的MODBUS协议实现HMI与脱机控制器的可靠通讯.     

超级电容器在汽车启动中的应用

根据超级电容器的结构特性,介绍在汽车启动过程中如何利用超级电容器减小对车内其他电子设备的干扰,改善汽车的启动性能,延长蓄电池使用寿命.     

基于C6711处理器cdma2000 1X系统前向信道信号的处理

在cdma20001x前向信道中,要对一段信号进行传送,一般选用QPSK调制,因为QPSK调制比QAM更适合噪音环境。采用TI6000系列的TMS320C6711芯片处理前向信道信号,可以对复杂性和实时性较高的信号做采集、量化、编码、调制等实时处理,主要功能通过软件编程实现,从而使系统具有结构灵活、可靠性高、可扩展等优点。     

火炮身管内表面激光硬化处理的实验研究

提高身管寿命是火炮行业亟待解决的关键技术问题，激光表面改性技术是解决这一问题的有效方法之一。本文在分析激光表面相变硬化性能的基础上，对身管内表面进行了激光硬化处理实验研究，检测了其内表面阳线和阴线的硬化层硬度和深度，对比分析了离焦量和焦深对其内表面硬化层硬度的影响，并对激光相变硬化层金相组织进行了分析。经激光硬化处理后，身管的内表面硬度有明显提高，硬化层较深，且为很细的条状马氏体组织。     

机械力化学作用对低介硅灰石瓷料的相变和相组成的影响

采用X射线衍射仪(XRD)、差热分析(DTA)手段详细研究了由氧化物粉末制备硅灰石陶瓷时,机械力化学作用及后续热处理对硅灰石陶瓷相组成和相变过程的影响,分析了机械力化学在球磨过程中的作用机理主要是细化晶粒、使晶格畸变、晶格缺陷增多、非晶化和诱导低温化学反应。结果表明:高能球磨中的机械力化学作用能够有效地降低硅灰石陶瓷的烧成温度(11160~11220℃)。探明了经高能球磨的样品在烧成过程中的晶相转变规律。瓷料最终的晶相为单一的-硅灰石(高温变体)。