Charge transfer resistance of spray deposited and compressed counter electrodes for dye-sensitized nanoparticle solar cells on plastic substrates

Electrochemical impedance spectroscopy was used to determine the effective charge transfer resistances of porous dye-sensitized solar cell counter electrodes prepared by low-temperature spray deposition and compression of conductive carbon and platinized Sb-doped SnO₂ powders on indium tin oxide-coated plastic substrates. The charge transfer resistances were 0.5–2 and 8–13 Ω cm², respectively, when using 3-methoxypropionitrile as the electrolyte solvent. The manufacturing method used lends itself to produce mechanically stable and even-quality electrodes in an easy and fast manner.     

Promising alloys for intermediate-temperature solid oxide fuel cell interconnect application

The formation of a low Cr-volatility and electrically conductive oxide outer layer atop an inner chromia layer via thermal oxidation is highly desirable for preventing chromium evaporation from solid oxide fuel cell (SOFC) metallic interconnects at the SOFC operation temperatures. In this paper, a number of ferritic Fe–22Cr alloys with different levels of Mn and Ti as well as a Ni-based alloy Haynes 242 were cyclically oxidized in air at 800 °C for twenty 100-h cycles. No oxide scale spallation was observed during thermal cycling for any of these alloys. A mixed Mn₂O₃/TiO₂ surface layer and/or a (Mn, Cr)₃O₄ spinel outer layer atop a Cr₂O₃ inner layer was formed for the Fe–22Cr series alloys, while an NiO outer layer with a Cr₂O₃ inner layer was developed for Haynes 242 after cyclic oxidation. For the Fe–22Cr series alloys, the effects of Mn and Ti contents as well as alloy purity on the oxidation resistance and scale area specific resistance were evaluated. The performance of the ferritic alloys was compared with that of Haynes 242. The mismatch in thermal expansion coefficient between the different layers in the oxide scale was identified as a potential concern for these otherwise promising alloys.     

Studies on the corrosion behavior of cerium-implanted zircaloy-4 with GAXRD

In order to study the influence of cerium ion implantation on the aqueous corrosion behavior of zircaloy-4, specimens were implanted by cerium ions with a fluence range from 1×10¹⁶ to 1×10¹⁷ ions/cm² at maximum 150°C, using MEVVA source at an extracted voltage of 40 kV. The valence and elements penetration distribution of the surface layer were analyzed by X-ray photoelectron spectroscopy (XPS) and auger electron spectroscopy (AES) respectively. Glancing angle X-ray diffraction (GAXRD) was employed to examine the phase transformation due to the cerium ion implantation in the oxide films. Three-sweep potentiodynamic polarization measurement was employed to value the aqueous corrosion resistance of zircaloy-4 in a 1 N H₂SO₄ solution. It was found that a significant improvement in the aqueous corrosion behavior of zircaloy-4 implanted with cerium ions compared with that of the as-received zircaloy-4. The improvement effect will declined with raising the implantation fluence. The bigger is the fluence, the less is the improvement. Finally, the mechanism of the corrosion behavior of the cerium-implanted zircaloy-4 is discussed.     

考虑加筋切向阻力的土坡稳定分析

目前在加筋边坡的极限平衡稳定分析中,认为加筋中产生的预应力能约束土体的运动或者能使抵抗土体运动的阻力增加,而对于加筋的切向阻力作用却没有考虑。主要讨论了在加筋土坡稳定分析时,加筋的切向阻力在加筋工程中起到的作用。认为在加筋边坡的极限平衡稳定分析中,也应考虑加筋的切向阻力作用;提出了计算公式,编制了相应的程序,给出了算例。     

高硬度耐磨电弧喷涂管状丝材的研究

利用自熔性合金与非晶态材料的特点，研制了Fe—B系管状丝材作为电弧喷涂材料，其形成的涂层具有良好的结合强度、低的孔隙率、高的硬度和耐磨损性能。     

高强度钢的Zn—Ti合金新镀层

本文研究了一种Ｚｎ－Ｔｉ合金新镀层，经盐水浸泡、中性盐雾和大气暴露试验结果试验，其耐蚀明显超过镀Ｚｎ层，并与镀Ｃｄ层相近，用缺口持久拉伸试验检验氢脆性，拉伸持续时间超过２００ｈ，达到原航空部部颁标准（ＨＢ５０６７－８５），该镀层适用于高强度钢防护。     

Electrosynthesis and impedance studies on zinc selenide

Electrochemical impedance measurements have been used to characterize zinc selenide films prepared by electrochemical co-deposition at a platinum rotating disk electrode. Estimations of capacitance and polarization resistance of variously prepared electrodeposits have been carried out to determine charge carrier density and corrosion rates.     

十三陵蓄能电站上水库自动监测系统的设计及运行

由于十三陵蓄能电站上水库地处蟒山之巅，所在山体地质条件复杂。施工期埋设了大量的监测仪器，原有人工监测系统效率低、资料分析的同步性差。2002年5月，对其进行了自动化改造，现已有一套符合其特点的自动化监测系统。十三陵上水库水工建筑自动监测系统已正常运行了三年，同时也存在着问题，有待于进一步的探讨和改进。     

Procedures for analysis of strain transfer in the acetabular region in vitro

The failure of acetabular cups via loosening, migration or fracture is partially related to the stress distribution existing in the acetabular region. The complexity of the investigation of these stresses demands the application of a variety of model testing techniques involving combined embedded strain gauging, finite element analysis, transmission and reflective photoelasticity and crack propagation studies. The application of these procedures are described and the difficulties of obtaining representative loadings and restraints are commented upon.     

Stepwise-Graded Si3N4–SiC Ceramics with Improved Wear Properties

The processing of stepwise graded Si₃N₄/SiC ceramics by pressureless co-sintering is described. Here, SiC (high elastic modulus, high thermal expansion coefficient) forms the substrate and Si₃N₄ (low elastic modulus, low thermal expansion coefficient) forms the top contact surface, with a stepwise gradient in composition existing between the two over a depth of ∼1.7 mm. The resulting Si₃N₄ contact surface is fine-grained and dense, and it contains only 2 vol% yttrium aluminum garnet (YAG) additive. This graded ceramic shows resistance to cone-crack formation under Hertzian indentation, which is attributed to a combined effect of the elastic-modulus gradient and the compressive thermal-expansion-mismatch residual stress present at the contact surface. The presence of the residual stress is corroborated and quantified using Vickers indentation tests. The graded ceramic also possesses wear properties that are significantly improved compared with dense, monolithic Si₃N₄ containing 2 vol% YAG additive. The improved wear resistance is attributed solely to the large compressive stress present at the contact surface. A modification of the simple wear model by Lawn and co-workers is used to rationalize the wear results. Results from this work clearly show that the introduction of surface compressive residual stresses can significantly improve the wear resistance of polycrystalline ceramics, which may have important implications for the design of contact-damage-resistant ceramics.