Electrical and mechanical properties of BZT − xBCT lead-free piezoceramics

In this study, lead-free (1 − x)Ba(Zr_0.2Ti_0.8)O₃ − x(Ba_0.7Ca_0.3)TiO₃ compositions are synthesized via conventional solid oxide route, and the ceramics are fabricated with normal sintering in air. The effects of composition fluctuations on dielectric, piezoelectric, and mechanical properties are investigated. The phase structure and the microstructure are analyzed with X-ray diffraction and scanning electron microscopy. The best dielectric and piezoelectric properties of ε_r = 11 207 and d₃₃ = 330 pC/N were obtained for BZT−0.35BCT and BZT−0.5BCT ceramics, respectively. The mechanical behavior—in terms of Vickers hardness and compressive and flexural strengths—was investigated, and the best mechanical behavior was found in the vicinity of the phase transition boundary with x values between 0.5 and 0.6.     

Electrical Breakdown Properties and Space Charge Formation in High Temperature Region in Ultraviolet Ray Irradiated PVC

Polyvinyl chloride (PVC) is the most popular insulating material for electric wiring instruments. However, an exothermic reaction above 150 °C may cause deterioration of the insulating properties of PVC. Therefore, it is important to clarify the heat degradation in PVC, not only to investigate the ignition of electrical wiring products but also to use electrical products safely. It is known that ultraviolet (UV) irradiation causes chemical deterioration of PVC and an increase in its conductivity. Generally, it has been thought that the electrical breakdown properties, electrical conduction, and insulating performance are affected by space charge accumulation in an insulating material. A high temperature pulsed electroacoustic (PEA) system usable up to 250 °C has been developed, and the PEA system can measure the space charge distribution and conduction current in the high temperature range simultaneously. In this investigation, the space charge distribution and conduction current were measured up to electrical breakdown in a non‐UV irradiated sample (normal PVC) and in 353 nm and 253 nm UV‐irradiated PVC samples in the range from room temperature to 200 °C in a DC electric field. In the short wavelength UV irradiated PVC sample (253 nm, 300 h), a deterioration of breakdown strength at 90 °C to 150 °C and negative packet‐like charges were observed at 60 °C and 100 °C, a positive charge accumulated in front of both the anode and cathode above 90 °C, and a higher electric field near the cathode side because the positive charge of the cathode side was greater.     

VRDS装置增加上流式反应器的技术分析

介绍了世界上第1套上流式反应器技术(UFR)在胜利炼油厂渣油加氢脱硫(VRDS)装置的生产运行情况。结果表明:UFR技术可以极大地优化VRDS装置的运转,减少装置运转的苛刻度,有效地延长装置运转周期,提高装置的经济效益。     

RHT系列渣油加氢催化剂在胜利炼油厂VRDS装置上的工业应用

介绍由北京石油化工研究院研制、开发、用于渣油加氢装置固定床反应器的RHT系列催化剂在胜利炼油厂VRDS装置的首次工业应用情况。该催化剂采用自行开发的级配路线,较好地结合了脱金属剂、脱硫剂、脱氮剂的性能特点,使整个运行周期的催化剂活性和稳定性达到较好地匹配,已达到同类进口催化剂的水平。     

长距离管输对3号喷气燃料导电性能和清洁性能的影响

分析了长距离管输后3号喷气燃料电导率严重衰减的原因和补加抗静电剂后对3号喷气燃料电导率和水反应指标的影响。对比了成品油长距离管输和喷气燃料馏分长距离管输对3号喷气燃料电导率和水反应指标的影响，并对比了两种管输方式的优缺点，提出对3号喷气燃料的管输建议。3号喷气燃料的长距离管输，优先采用喷气燃料馏分油管输在末端加注抗静电剂的方式；需兼顾汽运时，宜采用成品油管输并在末端根据电导率衰减情况，最小量补加抗静电剂的方式，以获得较高的成功率和较好的经济效益。     

新形势下电气工程及其自动化专业人才培养模式与知识体系框架

在分析了当前高等教育培养基本模式的基础上，根据科学技术和社会经济发展的要求，提出了人才培养的模式和要求。特别针对电气工程及其自动化领域的发展趋势以及对人才的需求，提出了该专业人才的知识框架体系。     

电磁发射兵器用电容器的选取

本文首先从理论上论述了膜电容器的储能密度与寿命之间的关系，对国际电容器制造水平和趋势进行了分析，提出采用干式金属化膜电容器作为储能元件。最后，根据电磁发射兵器整体寿命配合原则，提出高储能密度脉冲电容器的合理寿命指标。     

微桥法镍膜的弹性模量和残余应力测量

利用MEMS技术制作了不同尺寸的镍(Ni)膜微桥结构样品。采用纳米压痕仪XP系统测量了微桥载荷与位移的关系,并结合微桥力学理论模型得到了两种不同尺寸的Ni膜的弹性模量和残余应力。结果表明,两种不同尺寸的Ni膜的弹性模量结果一致,为190 GPa左右,但是残余应力变化较大。与采用纳米压痕仪直接测得的带有硅(Si)基底的Ni膜弹性模量186.8 7.5 GPa相比较,两者符合较好。     

高功率脉冲水中放电的应用及其发展

首先介绍了高功率脉冲水下放电的机理，然后综合论述了其应用和研究的状况，从较为成熟的脉冲水处理技术到医疗领域的ESWL应用技术，以及在脉冲电场食品杀菌和水下目标探测方面的最新发展和研究，最后指出了高功率脉冲电技术应用前景以及进行更系统和深入研究的必要性。