Fabrication of Porous SiC Ceramics with Special Morphologies by Sacrificing Template Method

Sacrificial template technique is widely used in producing porous materials with controlled morphologies and tailored properties. In this paper, unique templates such as filters, carbon nanotube, carbon fiber and silica were used to make porous SiC ceramic with special morphologies. Template derived porous ceramic plates, SiC nano-net, fiber-inverse and bead-inverse porous SiC ceramic were successfully prepared from the preceramic precursor, polymethylsilane (PMS). The synthesis procedures were involved with the infiltration of the templates with appropriate concentration of the preceramic polymer, their curing, pyrolysis and subsequent template removal. The synthesized porous SiC was characterized by SEM, TEM, XRD and BET methods.     

基于并查集和边缘检测模板的非理想虹膜定位

非理想虹膜图像往往存在虹膜边缘模糊、灰度变化不均匀、位置偏移及光斑干扰等问题, 这些问题的存在会在一定程度上影响虹膜内、外边界定位的准确率. 针对这个问题, 本文提出采用并查集和边缘检测模板的方法来对非理想虹膜进行内、外边界定位. 内边界定位是首先采用并查集方法完成瞳孔区域粗定位, 然后采用Hough变换对瞳孔进行精确定位; 外边界定位是先利用一系列边缘检测模板大致确定外圆的位置, 然后再依据外边界附近圆环内边缘点的密度来最终完成外边界的精确定位. 实验结果表明, 对于非理想虹膜图像, 本文方法的定位正确率和定位速度均高于其他同类方法.     

Electroplating synthesis and electrochemical properties of macroporous Sn-Cu alloy electrode for lithium-ion batteries

Macroporous material of Sn-Cu alloy of different pore sizes designated as anode in lithium-ion batteries were fabricated through colloidal crystal template method. The structure and electrochemical properties of the macroporous Sn-Cu alloy electrodes were examined by using scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and galvanostatic cycling. The results demonstrated that the electrodes of macroporous Sn-Cu alloy with pore size respectively of 180 and 500 nm can deliver reversible capacity of 350 and 270 mAh g⁻¹ up to 70th cycles of charge/discharge. The cycle performance of the macroporous Sn-Cu alloy of 180 nm in pore size is better than that of the macroporous Sn-Cu alloy with 500-nm-diameter pores. It has revealed that the porous structure of the macroporous Sn-Cu alloy material is of importance to strengthen mechanically the electrode and to reduce significantly the effect of volume expansion during cycling.     

基于模板法制备两亲性Janus纳米粒子及其应用进展

Janus粒子是同一粒子中含有两种不同化学组成的非对称结构,其中两亲性Janus粒子是在对立面分别含有亲水基、疏水基两种不同化学基团,作为一种新型纳米材料受到广泛的关注。该文综述了模板法制备不对称结构的两亲性Janus粒子以及其应用领域,包括硬模板法、软模板法、牺牲模板法以及无模板法;综述了两亲性Janus粒子在表面活性剂、牙科粘合剂、微胶囊、功能涂层、催化剂以及生物传感器等方面的研究进展。     

四丁基氢氧化胺模板磷酸铝对铬(Ⅵ)吸附性能的研究

研究了四丁基氢氧化胺模板磷酸铝对水中重金属离子铬(Ⅵ)的吸附特性。结果表明:四丁基氢氧化胺模板磷酸铝对铬(Ⅵ)吸附的最佳pH值和铬(Ⅵ)的初始质量浓度分别为2.0和40mg/L,且其吸附等温线符合Freundlich模型。     

纳米二氧化硅模板的制备

以微乳液法制备纳米二氧化硅（SiO2）粒子，经压制、烧结制备SiO2模板。通过红外（IR）、热分析（TGDTA）、扫描电镜（SEM）等方法对SiO2模板进行表征，结果表明所得SiO2粒度在100nm左右．烧结温度在800℃时，SiO2粒子之间将实现颈长，有利于有机／无机杂化多孔材料的制备。     

维吾尔新文字大小写同形字母的识别

为有效识别出新维文中大小写同形字母,分析新维文的特点,提出一种基于模板匹配的大小写同形字母识别算法。根据同形字母中大写字母外轮廓大而小写字母外轮廓小的特点,统计字母外轮廓大小与全文字母外轮廓平均大小的比例值,进行字母的大小写判断。分析结果表明,该方法有效克服了传统模板匹配方法容易混淆同形字母的大小写的缺点,提高了系统的识别率。     

A Novel Mixed-Valence Tetranuclear Iron-Oxygen Clusters in the Organically Templated Iron Phosphate [H3N(CH2)2NH3]2 Fe4O(PO4)4 ċH2O

A novel iron phosphate templated with ethylenediammonium cation, [H₃N(CH₂)₂NH₃]₂ Fe₄ O(PO₄)₄H₂O, has been synthesized hydrothermally and characterized by single-crystal X-ray diffraction, thermo-gravimetric analysis, magnetic susceptibility and Mossbauer spectroscopy. The compound crystallizes in the mono-clinic space group C2 with a= 30.3801(5),b= 10.1204(5),c= 10.0977(5) Å, = 107.712(1)°, V = 2957.5(4) ų and Z = 6. The structure contains 5 and 6-coordinated Fe atoms bridged by ₄-oxygen and PO₄ groups to form two types of mixed-valence Fe₄P₄ cubane-like clusters, which are connected via Fe- O- P bonds to give rise to intersecting channels that house the ethylenediammonium cations and water molecules. Room-temperature Mossbauer data confirm the presence of Fe^II and Fe^III.     

Porous TiC Ceramics Derived from Wood Template

A porous TiC ceramic with a woodlike structure was prepared from wood template through tetrabutyl titanate vacuum-infiltration. The tetrabutyl titanate was first decomposed to TiO₂, and then in-situ reaction between TiO₂ and carbon template took place in the cellular wall at high sintering temperature. The original structure of wood was retained. In addition, the dimensional shrinkage of the pores after the removal of the residual carbon was different according to the difference of the wood density.     

多孔氧化铝模板法制备取向碳纳米管阵列的研究进展

利用化学气相沉积技术在多孔氧化铝模板上可以制备取向碳纳米管阵列。通过调节阳极氧化参数可以改变模板的孔结构,进而可控制碳纳米管在孔道中生长的形貌。用这种方法制备的碳纳米管的直径、长度和密度可以选择性控制,这将有利于研究碳纳米管的性质和它在电化学及其他领域的应用。介绍了多孔氧化铝模板的形成原理以及碳纳米管在多孔氧化铝模板上的生长机理,讨论了阳极氧化条件、催化剂和气相沉积温度对碳纳米管特性的影响,并指出了这种技术中一些需深入研究的问题。