非对称复合材料层板在面内载荷作用下的非线性横向变形或屈曲

本文利用广义富里叶级数法对非对称复合材料层板在面内载荷作用下的非线性横向变形或屈曲问题进行了分析。文中主要研究了四边简支边界条件下,非对称层板的铺层方式和面内载荷形式对横向变形的影响。通过求解非线性控制方程得到了层板的载荷—挠度曲线或特殊情况下的后屈曲平衡曲线。计算结果表明,对于大多数非对称复合材料层板在面内载荷作用下所产生的是横向变形问题,而不是分叉屈曲问题。     

采用荷载平衡的概念表达预应力度及在初步设计中的应用

利用荷载平衡法的概念，将预应力度用等效荷载与外荷载的比值表达，设计可利用其比值确定预应力度，便其更简捷，明确，同时，提出了预应力度的真实值问题。     

Nonlinear coupled problems in dynamics of shells

The coupled system of three partial differential equations governing a flexible shallow shell dynamics is analysed. No any prior assumptions about the temperature distribution through the shell thickness are applied. The efficiency of the method used here when applied to the solution of integral-differential equations with different dimensions (three-dimensional equations related to the Kirchhoff-Love model) and of different type (heat transfer equations and the hyperbolic equations of shell theory) is demonstrated. Many computational results are reported and discussed.     

Behavior of a Semiintegral Bridge Abutment under Static and Temperature-Induced Cyclic Loading

This paper presents the results of an experimental study of semiintegral bridge abutments. Primary interests were to investigate (1) potential problems with the particular detail tested; (2) rotational characteristics of the semiintegral abutments; and (3) ability of the specimens to withstand cyclic loading induced by temperature variations during the expected life of the bridge. Sixteen experiments were conducted on three large-scale specimens. The results of the tests have shown that semiintegral abutments can significantly reduce the moments transferred from the superstructure to the foundation piles. Test results have also shown that semiintegral abutments can tolerate the number of displacement cycles that a bridge will experience during the course of its economic life.     

Service Load Effective Compression Flange Width in Fiber Reinforced Polymer Deck Systems Acting Compositely with Steel Stringers

This paper reports on the field study of a steel stringer-fiber reinforced polymer (FRP) deck composite bridge in Pennsylvania. The objective of the study is to assess the effective compression flange width in the FRP deck and floor systems when they act compositely with underlying steel girders at service conditions. The research results reported herein support the notion of employing a design approach, for both interior and exterior girders of a composite floor system, that is philosophically consistent with current practice related to steel girders acting compositely with concrete decking. It appears from the results presented herein that FRP decks and floors acting compositely with underlying steel girders exhibit an effective width that is close to the actual girder spacing for interior beams, and approximately one-half this value for exterior beams.     

Biofiltration of toluene in the absence and the presence of ethyl acetate under continuous and intermittent loading

BACKGROUND: Two peat biofilters were used for the removal of toluene from air for one year. One biofilter was fed with pure toluene and the other received 1:1 (by weight) ethyl acetate:toluene mixture. RESULTS: The biofilters were operated under continuous loading: the toluene inlet load (IL) at which 80% removal occurred was 116 g m^?3 h^?1 at 57 s gas residence time. Maximum elimination capacity of 360 g m^?3 h^?1 was obtained at an IL of 745 g m^?3 h^?1. The elimination of toluene was inhibited by the presence of ethyl acetate. Intermittent loading, with pollutants supplied for 16 h/day, 5 days/week, did not significantly affect the removal efficiency (RE). Biomass was fully activated in 2 h after night closures, but 6 h were required to recover RE after weekend closures. Live cell density remained relatively constant over the operational period, while the dead cell fraction increased. Finally, a 15 day starvation period was applied and operation then re‐started. Performance was restored with similar re‐acclimatization period to that after weekend closures, and a reduction in dead cell fraction was observed. CONCLUSION: This study demonstrates the capacity of the system to handle intermittent loading conditions that are common in industrial practices, including long‐term starvation. Copyright © 2008 Society of Chemical Industry     

Rotational Restraint of Pile Caps during Lateral Loading

A pure fixed-head (zero-rotation) condition at the top of a group of laterally loaded piles is seldom achievable in the field, even when piles are installed in a group that is “rigidly” constrained by a stiff concrete pile cap. Assuming complete fixity during design (zero rotation at the pile head) can result in underestimated values of pile-head deflection, and incorrect estimates of the magnitude and the location of maximum bending moments. A simple and practical approach is presented for estimating the moment restraint that is provided by the pile cap at the top of a pile group. The moment restraint, represented by the rotational restraint coefficient (KMθ), serves as a boundary condition for analyzing groups of laterally loaded piles. Full-scale field tests performed on two pile groups with concrete pile caps show that the proposed method for estimating rotational restraint provides results that are in good agreement with measured field performance.     

钢丝绳牵引胶带输送机动力制动系统改造

介绍了钢丝绳牵引胶带输送机制动系统改造方案前、后的对比。     

“Biaxiality Effect” on the Energy Dissipated by Elastoplastic Base-Isolators

A plane elastic-plastic solid body presenting kinematic hardening is used to simulate a pair of dampers at the base of a rigid structure and determine the energy dissipation under conditions of assigned, homogeneous cyclic loading. The well-known von Mises theory of plasticity is applied with the aim of obtaining analytical solutions to the problem. Such solutions are arrived at by first calculating the Odqvist parameter, which yields dimensionless relations that depend on the external loads and mechanical properties of the material. The results, in terms of dissipated energy, are given for the case of a sinusoidal process, represented with the help of dimensionless parameters useful for engineering applications.     

Exact solution of elasto-plastic stresses in a metal-matrix composite beam of arbitrary orientation subjected to transverse loads

An analytical elasto-plastic stress analysis is presented for a metal-matrix composite beam of arbitrary orientation subjected to a single transverse force applied to the free end of the beam and a uniformly distributed load. The material is assumed to be perfectly plastic in the elasto-plastic solution. A composite consisting of stainless-steel-reinforced aluminum was produced for this work. Sample problems are given for various orientation angles. Elastic, elastoplastic and residual normal and shear stresses are calculated. The location of the elasto-plastic boundary of the beam is obtained according to the x coordinates of the beam.