Study of the morphology and mechanical properties of polypropylene composites with silica or rice‐husk

The mechanical, morphological behavior and water absorption characteristics of polypropylene (PP) and silica, or PP and rice‐husk, composites have been studied. The silica used in this study as filler was a commercial type produced from soluble glass or rice husks. The compatibilizing effect of PP grafted with monomethyl itaconate (PP‐g‐MMI) and/or with vinyltriethoxysilane (PP‐g‐VTES) as polar monomers on the mechanical properties and water absorption was also investigated. In general, a high loading of the studied fillers in the polymer matrix increases the stiffness and the water absorption capacity. This effect is more noticeable in the tensile modulus of the PP/silica composite with PP‐g‐VTES as compatibilizer. However, the increase of the rice‐husk charge as a natural filler in the PP matrix decreases the stiffness, and in the presence of PP‐g‐MMI as compatibilizer in PP/rice‐husk, the tensile modulus and water absorption of the composite were improved. The better adhesion and phase continuity in the PP/silica and PP/rice‐husk composites with different compatibilizers was confirmed by the morphological study. Copyright © 2004 Society of Chemical Industry     

Fatigue Behavior and Retrofit Investigation of Distortion-Induced Web Gap Cracking

This paper studies a Kansas Department of Transportation welded plate girder bridge that developed fatigue cracks at small web gaps close to the girder top flange. Repair had been previously performed by softening the connection plate end with a slot retrofit, but cracks were recently found to have reinitiated at some of the repaired details and are again propagating. A comprehensive finite-element method study was performed to investigate the cracking behavior observed in the bridge and to recommend appropriate measures for future bridge retrofit. The analytical results show that stresses developed at the top flange web gaps could exceed yielding under the loading of an HS15 fatigue truck. The current slot repair used in the bridge was found to have introduced higher magnitude fatigue stresses in the web gap. To achieve a permanent repair of the bridge, it is recommended that a welded connection plate to flange attachment be used during future bridge retrofit. The web gap details should be able to withstand unlimited number of load cycles once this additional repair is performed.     

Challenges in the Application of Stochastic Modal Identification Methods to a Cable-Stayed Bridge

This paper presents an analysis of the data collected in the ambient vibration test of the International Guadiana cable-stayed Bridge, which links Portugal and Spain, based on different output-only identification techniques: peak-picking, frequency domain decomposition, covariance-driven stochastic subspace identification, and data-driven stochastic subspace identification. The purpose of the analysis is to compare the performance of the four techniques and evaluate their efficiency in dealing with specific challenges involved in the modal identification of the tested cable-stayed bridge, namely the existence of closely spaced modes, the perturbation produced by the local vibration of stay-cables, and the variation of modal damping coefficients with wind velocity. The identified natural frequencies and mode shapes are compared with the corresponding modal parameters provided by a previously developed numerical model. Additionally, the variability of some modal damping coefficients is related with the variation of the wind characteristics and associated with a component of aerodynamic damping.     

Deflection Calculation of FRP Reinforced Concrete Beams Based on Modifications to the Existing Branson Equation

Fundamental concepts of tension stiffening are used to explain why Branson’s equation for the effective moment of inertia Ie does not predict deflection well for fiber reinforced polymer (FRP) reinforced concrete beams. The tension stiffening component in Branson’s equation is shown to depend on the ratio of gross-to-cracked moment of inertia (Ig/Icr), and gives too much tension stiffening for beams with an Ig/Icr ratio greater than 3. FRP beams typically have an Ig/Icr ratio greater than 5, leading to a much stiffer response and underprediction of computed deflections as observed by others in the past. One common approach to computing deflection of FRP reinforced concrete beams has been to use a modified form of the Branson equation. This paper presents a rational development of appropriate modification factors needed to reduce the tension stiffening component in Branson’s original expression to realistic levels. Computed deflections using this approach give reasonable results with the right modification factor, and compare well with a more general unified approach that incorporates a realistic tension stiffening model. Comparison is made with the existing and past correction factors recommended by ACI 440 for predicting deflection of FRP beams. The method presently used by ACI 440 gives reasonable estimates of deflection for glass and carbon FRP reinforced beams. However, this method underestimates deflection of aramid FRP reinforced beams and is restricted to rectangular sections. A proposal is made for adoption of a simple modification factor that works well for all types of FRP bar and beam cross-sectional shape.     

Mining for trigger events with survival analysis

This paper discusses a new application of data mining, quantifying the importance of responding to trigger events with reactive contacts. Trigger events happen during a customer’s lifecycle and indicate some change in the relationship with the company. If detected early, the company can respond to the problem and retain the customer; otherwise the customer may switch to another company. It is usually easy to identify many potential trigger events. What is needed is a way of prioritizing which events demand interventions. We conceptualize the trigger event problem and show how survival analysis can be used to quantify the importance of addressing various trigger events. The method is illustrated on four real data sets from different industries and countries.     

油气集输系统新增产能建设拓扑优化方法研究

在油气集输新增产能建设中,为充分利用已建管网系统的处理能力,达到降低投资,提高经济效益的目的,进行了油气集输新增产能建设布局优化方法的研究。针对新建集输管网为树状结构的情况,建立了油气集输系统新增产能建设拓扑优化的数学模型,讨论了计算复杂性问题。根据模型的特点,将问题分解为拓扑级优化和几何级优化两个子问题,并通过它们之间的迭代进行求解。实例计算表明,所建立的数学模型正确,求解方法可行,能用于工程实际设计。     

Synthesis of 2,7‐Carbazolenevinylene‐Based Copolymers and Characterization of Their Photovoltaic Properties

New electroactive and photoactive conjugated copolymers consisting of alternating 2,7‐carbazole and oligothiophene moieties linked by vinylene groups have been developed. Different oligothiophene units have been introduced to study the relationship between the polymer structure and the electronic properties. The resulting copolymers are characterized by UV‐vis spectroscopy, size‐exclusion chromatography, and thermal and electrochemical analyses. Bulk heterojunction photovoltaic cells from different copolymers and a soluble fullerene derivative, [6,6]‐phenyl‐C₆₁ butyric acid methyl ester, have been fabricated, and promising preliminary results are obtained. For instance, non‐optimized devices using poly(N‐(4‐octyloxyphenyl)‐2,7‐carbazolenevinylene‐alt‐3″,4″‐dihexyl‐2,2′;5′,2″;5″,2″′;5″′,2″″‐quinquethiophenevinylene 1″,1″‐dioxide) as an absorbing and hole‐carrier semiconductor exhibit power conversion efficiency up to 0.8 % under air mass (AM) 1.5 illumination. These features make 2,7‐carbazolenevinylene‐based and related polymers attractive candidates for solar‐cell applications.     

Low Electrical Percolation Threshold of Silver and Copper Nanowires in Polystyrene Composites

Silver and copper nanowires have been synthesized using a scalable method of AC electrodeposition into porous aluminum oxide templates, which produces gram quantities of metal nanowires ca. 25 nm in diameter and up to 5 and 10 μm in length for Ag and Cu, respectively. The nanowires have been used to prepare polystyrene nanocomposites by solution processing. Electrical resistivity measurements performed on polymer nanocomposites containing different volume fractions of metal indicate that low percolation thresholds of nanowires are attained between compositions of 0.25 and 0.75 vol %.