转载溜槽衬板磨损预测的DEM仿真方法

针对EDEM自动划分网格较稀疏问题,采用Hypermesh划分仿真模型网格,利用Herz-Mindlin接触理论的Archard磨损模型对转载溜槽磨损问题进行仿真,在网格单元上提取出漏斗和溜管衬板的接触能量和磨损量,分析了磨损量与接触能量的关系。假设转载溜槽衬板磨损深度为物料与溜槽衬板的使用时间为线性函数,根据现场衬板磨损量的测量值,将衬板的磨损系数关系的看作隐式的单变量方程,应用EDEM软件的仿真结果求解出磨损系数的标定值。分析了漏斗和溜管的磨损机理。该方法可用于转载溜槽的磨损预测。     

Etching characteristics of thin SiON films using a liquefied perfluorocarbon precursor of C6F12O with a low global warming potential

Perfluorocarbon gas is widely used in the semiconductor industry. However, perfluorocarbon has a negative effect on the global environment owing to its high global warming potential (GWP) value. An alternative solution is essential. Therefore, we evaluated the possibility of replacing conventional perfluorocarbon etching gases such as CHF₃ with C₆F₁₂O, which has a low GWP and is in a liquid state at room temperature. In this study, silicon oxynitride (SiON) films were plasma-etched using inductively coupled CF₄ +C₆F₁₂O+O₂ mixed plasmas. Subsequently, the etching characteristics of the film, such as etching rate, etching profile, selectivity over Si, and photoresist, were investigated. A double Langmuir probe was used and optical emission spectroscopy was performed for plasma diagnostics. In addition, a contact angle goniometer and x-ray photoelectron spectroscope were used to confirm the change in the surface properties of the etched SiON film surface. Consequently, the etching characteristics of the C₆F₁₂O mixed plasma exhibited a lower etching rate, higher SiON/Si selectivity, lower plasma damage, and more vertical etched profiles than the conventional CHF₃ mixed plasma. In addition, the C₆F₁₂O gas can be recovered in the liquid state, thereby decreasing global warming. These results confirmed that the C₆F₁₂O precursor can sufficiently replace the conventional etching gas.     

A novel fast distance relay for series compensated transmission lines

This paper presents a fast distance relay for series compensated transmission lines based on the R–L differential-equation algorithm using the theory of equal transfer process of transmission lines. The measuring distances based on the proposed algorithm can fast approach the actual value of fault distance when a fault occurs in front of the series capacitor. When a fault occurs behind of the series capacitor, the fault loop, including the series capacitor, does not match the R–L transmission line model, so the measuring distances fluctuate severely. Based on this, the relative position of the fault with respect to the series capacitor can be judged effectively according to the fluctuation range of the measuring distances, and the accurate fault location can be obtained fast. A variety of PSCAD/EMTDC simulation tests show that the new relay has fast operating speed and high accuracy when applied to the long series compensated transmission lines.     

Experimental study on the heat transfer and flow characteristics of nanorefrigerants inside a corrugated tube

The heat transfer and flow characteristics of MWCNT-R141b nanorefrigerant with different mass fractions have been studied through experiments. Experimental results were compared with existing correlations. A two-step method was used to prepare the nanorefrigerants. Span-80 was used as surfactant with an average particle diameter of 20 nm. Transmittance method was used to evaluate the stability of nanorefrigerants. Results showed that the stability of MWCNT-R141b nanorefrigerant, which is the added dispersant, was good during the experiments. The 0.3 wt% MWCNT-R141b nanorefrigerants had optimal heat transfer enhancement effects compared with pure refrigerants. The maximum Nusselt number increased by 40%. The specific pressure drop of nanorefrigerant increased as the Reynolds number (Re) increased, and the specific pressure drop of the pure refrigerant was minimum, which is similar to R141b.     

Accounting for the uncertainties in the estimation of average shear wave velocity using V S– N correlations

Site-specific seismic hazard analysis is crucial for designing earthquake resistance structures, particularly in seismically active regions. Shear wave velocity ( V _S) is a key parameter in such analysis, although the economy and other factors restrict its direct field measurement in many cases. Various V _S–SPT– N correlations are routinely incorporated in seismic hazard analysis to estimate the value of V _S. However, many uncertainties question the reliability of these estimated V _S values. This paper comes up with a statistical approach to take care of such uncertainties involved in V _S calculations. The measured SPT– N values from all the critical boreholes were converted into statistical parameters and passed through various correlations to estimate V _S at different depths. The effect of different soil layers in the boreholes on the Vs estimation was also taken into account. Further, the average shear wave velocity of the top 30 m soil cover ( V _S30) is estimated after accounting for various epistemic and aleatoric uncertainties. The scattering nature of the V _S values estimated using different V _S– N correlations was reduced significantly with the application of the methodology. Study results further clearly demonstrated the potential of the approach to eliminate various uncertainties involved in the estimation of V _S30 using general and soil-specific correlations.     

刮板输送机中板仿生耐磨优化试验研究

刮板输送机中板磨损失效已成为输送机运行故障的主要原因之一，为了提高中板耐磨性，基于蜣螂非光滑单元进行了仿生中板设计，以磨损量为响应值，进行了单因素和响应面法优化试验。根据响应面法试验结果得到的因素显著性影响顺序（从高至低）依次为：径向距离，深径比，直径，节距角。基于试验结果建立了磨损量与因素的回归预测模型，经试验对比发现，预测模型与真实试验的相对误差为3.2%。在特定工况（煤散料粒度为6~8 mm、载荷为20 N、刮板链速为0.65 m/s及试验时长为6 600 s）下，当深径比为1.41、直径为0.69 mm、节距角为6.55°和径向距离为4.66 mm时，磨损量最小，仿生中板的耐磨性提高了12.6%。分析其耐磨机理发现，与光滑板相比，仿生板的磨粒磨损及黏着磨损较轻。凹坑分布可破坏持续切削中板表面的煤粒运动状态。中板的仿生优化可为今后刮板输送机的设计提供一定参考。     

Fundamental Evaluation of Power Supply and Rectifiers for Wireless Power Transfer Using Magnetic Resonant Coupling

This paper provides a fundamental analysis of a power supply and rectifiers for wireless power transfer using magnetic resonant coupling (MRC). MRC enables efficient wireless power transfer over middle‐range transfer distances. MRC for wireless power transfer should operate at a high frequency in the industry science medical band, such as 13.56 MHz, because the size of the transfer device decreases at higher transfer frequencies. Therefore, the output frequency of the power supply on the transmitting side should be 13.56 MHz. In addition, the rectifier on the receiving side is operated at a high frequency. This paper focuses on the reflected power in the power supply and rectifiers. Thus, the parametric design method is clarified for the power supply, including a low‐pass filter to match the output, the impedance of the power supply with the characteristic impedance of the transmission line. In addition, the effects on the rectifiers of silicon carbide and gallium nitride diodes are confirmed by performing an experiment and a loss analysis.     

Reactive Oxygen and Nitrogen Species in Defense/Stress Responses Activated by Chitosan in Sycamore Cultured Cells

Chitosan (CHT) is a non-toxic and inexpensive compound obtained by deacetylation of chitin, the main component of the exoskeleton of arthropods as well as of the cell walls of many fungi. In agriculture CHT is used to control numerous diseases on various horticultural commodities but, although different mechanisms have been proposed, the exact mode of action of CHT is still unknown. In sycamore (Acer pseudoplatanus L.) cultured cells, CHT induces a set of defense/stress responses that includes production of H₂O₂ and nitric oxide (NO). We investigated the possible signaling role of these reactive molecules in some CHT-induced responses by means of inhibitors of production and/or scavengers. The results show that both reactive nitrogen and oxygen species are not only a mere symptom of stress conditions but are involved in the responses induced by CHT in sycamore cells. In particular, NO appears to be involved in a cell death form induced by CHT that shows apoptotic features like DNA fragmentation, increase in caspase-3-like activity and release of cytochrome c from the mitochondrion. On the contrary, reactive oxygen species (ROS) appear involved in a cell death form induced by CHT that does not show these apoptotic features but presents increase in lipid peroxidation.