基于模糊多模型的堆芯功率控制

传统的堆芯功率PID控制器是基于单一功率水平处的堆芯局部模型设计的，难以准确描述整个堆芯功率水平范围的控制。因此，本文基于5个不同功率水平下的传递函数模型，通过三角隶属度函数加权，建立堆芯模糊多模型，并依据该模型设计堆芯功率模糊PID控制。以TMI型压水堆堆芯为对象，开展不同初始功率水平下的堆芯功率跟踪、堆芯进口温度扰动的控制仿真。结果表明，基于模糊多模型设计的堆芯功率模糊PID控制器可实现对堆芯功率的良好控制。     

Enhanced thermal stability of Bi2Te3-based alloys via interface engineering with atomic layer deposition

The ease of Te sublimation from Bi₂Te₃-based alloys significantly deteriorates thermoelectric and mechanical properties via the formation of voids. We propose a novel strategy based on atomic layer deposition (ALD) to improve the thermal stability of Bi₂Te₃-based alloys via the encapsulation of grains with a ZnO layer. Only a few cycles of ZnO ALD over the Bi₂Te_2.7Se_0.3 powders resulted in significant suppression of the generation of pores in Bi₂Te_2.7Se_0.3 extrudates and increased the density even after post-annealing at 500 °C. This is attributed to the suppression of Te sublimation from the extrudates. The ALD coating also enhanced grain refinement in Bi₂Te_2.7Se_0.3 extrudates. Consequently, their mechanical properties were significantly improved by the encapsulation approach. Furthermore, the ALD approach yields a substantial improvement in the figure-of-merit after the post-annealing. Therefore, we believe the proposed approach using ALD will be useful for enhancing the mechanical properties of Bi₂Te₃-based alloys without sacrificing thermoelectric performance.     

Optimized PI+ load–frequency controller using BWNN approach for an interconnected reheat power system with RFB and hydrogen electrolyser units

This paper investigates a renewable energy resource’s application to the Load–Frequency Control of interconnected power system. The Proportional-Integral (PI) controllers are replaced with Proportional-Integral Plus (PI+) controllers in a two area interconnected thermal power system without/with the fast acting energy storage devices and are designed based on Control Performance Standards (CPS) using conventional/Beta Wavelet Neural Network (BWNN) approaches. The energy storing devices Hydrogen generative Aqua Electroliser (HAE) with Fuel cell and Redox Flow Battery (RFB) are incorporated to the two area interconnected thermal power system to efficiently damp out the electromechanical oscillations in the power system because of their inherent efficient storage capacity in addition to the kinetic energy of the generator rotor, which can share the sudden changes in power requirements. The system was simulated and the frequency deviations in area 1 and area 2 and tie-line power deviations for 5% step- load disturbance in area 1 are obtained. The comparison of frequency deviations and tie-line power deviations of the two area interconnected thermal power system with HAE and RFB designed with BWNN controller reveals that the PI+ controller designed using BWNN approach is found to be superior than that of output response obtained using PI+ controller. Moreover the BWNN based PI+ controller exhibits a better transient and steady state response for the interconnected power system with Hydrogen generative Aqua Electroliser (AE) unit than that of the system with Redox Flow Battery (RFB) unit.     

Decomposition of first-order hybrid Petri nets for hierarchical control of manufacturing systems

Although hybrid Petri net (HPN) is a popular formalism in modelling hybrid production systems, the HPN model of large scale systems gets substantially complicated for analysis and control due to large dimensionality of such systems. To overcome this problem, a typical approach is to decompose the net into subnets and then control the plant through hierarchical or decentralized structures. Although this concept has been widely discussed in the literature for discrete PNs, there is a lack of research for HPNs. In this paper, a new method of decomposition of first-order hybrid Petri nets (FOHPNs) is proposed first and then the hierarchical control of the subnets through a coordinator is introduced. The advantage of using the proposed approach is validated by an existing example. A sugar milling case study is analysed by using a decomposed FOHPN model and the optimization results are compared against the results of the approaches presented in other papers. Simulation results show not only an improvement in production rate, but also show the ability to control the plant online. In addition, by using the hierarchical control structure for an FOHPN model, it is possible to reduce the cost of communication links, improve the reliability of the system, maintain the plant locally, and partially redesign the system.     

基于设备改造的选煤厂介质消耗控制研究

同忻选煤厂采用重介质选煤技术,磁性介质的消耗较大,为此,相关技术人员针对介质回收系统设备进行了改造设计。改造后,设备运行稳定,介质消耗降低,提高了原煤的分选效率,创造了较好的安全经济效益。     

注塑机料筒温度调控和计算机仿真研究

利用模糊控制和比例积分微分(PID)控制相结合的手段对注塑机料筒温度进行了控制,同时以Matlab 6.0软件为仿真平台,对料筒温度控制进行了模拟仿真研究。实验发现,在注塑机料筒升温过程中利用CHR整定的PID控制手段和模糊控制手段,恒温过程中利用人工整定的PID控制手段,可保证快速的料筒升温响应速率和稳定的保温过程。通过实际注塑实验对该仿真结果进行了验证,在十组实验中,料筒温度误差不超过2%,产品翘曲变形量不超过0.059 mm。     

Remarkably enhanced energy storage properties of lead-free Ba0.53Sr0.47TiO3 thin films capacitors by optimizing bottom electrode thickness

The lead-free Ba_0.53Sr_0.47TiO₃ (BST) thin films buffered with La_0.67Sr_0.33MnO₃ (LSMO) bottom electrode of different thicknesses were fabricated by pulsed laser deposition method on a (001) SrTiO₃ substrate. It was found that the roughness of electrode decreases and substrate stress relaxes gradually with the increase of LSMO thickness, which is beneficial for weakening local high electric field and achieving higher E_b. Therefore, the recoverable energy density (W_rec) of BST films can be greatly improved up to 67.3 %, that is, from 30.6 J/cm³ for the LSMO thickness of 30 nm up to 51.2 J/cm³ for the LSMO thickness of 140 nm after optimizing the LSMO thickness. Furthermore, the thin film capacitor with a 140 nm LSMO bottom electrode shows an outstanding thermal stability from 20 °C to 160 °C and superior fatigue resistance after 10⁸ electrical cycles with only a slightly decrease of W_rec below 1.6 % and 3.7 %, respectively. Our work demonstrates that optimizing bottom electrodes thickness is a promising way for enhancing energy storage properties of thin-film capacitors.     

Event-triggered variable horizon Supervisory Predictive control of hybrid power plants

The supervision of a hybrid power plant, including solar panels, a gas microturbine and a storage unit operating under varying solar power profiles is considered. The Economic Supervisory Predictive controller assigns the power references to the controlled subsystems of the hybrid cell using a financial criterion. A prediction of the renewable sources power is embedded into the supervisor. Results deteriorate when the solar power is unsteady, owing to the inaccuracy of the predictions for a long-range horizon of 10 s. The receding horizon is switched between an upper and a lower value according to the amplitude of the solar power trend. Theoretical results show the relevance of horizon switching, according to a tradeoff between performance and prediction accuracy. Experimental results, obtained in a Hardware In the Loop (HIL) framework, show the relevance of the variable horizon approach. Power amplifiers allow us to simulate virtual components, such as a gas microturbine, and to blend their powers with that of real devices (storage unit, real solar panels). In this case, fuel savings, reaching 15%, obtained under unsteady operating conditions lead to a better overall performance of the hybrid cell. The overall savings obtained in the experiments amount to 12%.     

Rectangular Section Control Technology for Silicon Steel Rolling

Rectangular section control technology(RSCT)was introduced to achieve high-precision profile control during silicon steel rolling.The RSCT principle and method were designed,and the whole RSCT control strategy was developed.Specifically,RSCT included roll contour design,rolling technology optimization,and control strategy development,aiming at both hot strip mills(HSMs)and cold strip mills(CSMs).Firstly,through the high-performance variable crown(HVC)work roll optimization design in the upper-stream stands and the limited shifting technology for schedule-free rolling in the downstream stands of HSMs,a hot strip with a stable crown and limited wedge,local spot,and single wave was obtained,which was suitable for cold rolling.Secondly,an approximately rectangular section was obtained by edge varying contact(EVC)work roll contour design,edge-drop setting control,and closed loop control in the upper-stream stands of CSMs.Moreover,complex-mode flatness control was realized by coordinating multiple shape-control methods in the downstream stands of CSMs.In addition,the RSCT approach was applied in several silicon-steel production plants,where an outstanding performance and remarkable economic benefits were observed.     

Nonlinear dynamic behaviors and control based on simulation of high-purity heat integrated air separation column

In this paper, the dynamic behaviors on the basis of simulation for high-purity heat integrated air separation column (HIASC) are studied. A nonlinear generic model control (GMC) scheme is proposed based on the nonlinear behavior analyses of a HIASC process, and an adaptive generic model control (AGMC) scheme is further presented to correct the model parameters online. Related internal model control (IMC) scheme and multi-loop PID (M-PID) scheme are also developed as the comparative base. The comparative researches are carried out among these linear and nonlinear control schemes in detail. The simulation research results show that the proposed AGMC schemes present advantages in both servo control and regulatory control for the high-purity HIASC.