Influence of ion bombardment on the properties and microstructure of unbalanced magnetron deposited niobium coatings

The effect of the ion bombardment to unbalanced magnetron deposited, approximately 1.5 and 4.5 μm thick, Nb coatings have been investigated as the bias voltage was varied from U_B=−75 to −150 V. Increasing bias voltage increased the hardness of the coating from 4.5 to 8.0 GPa. This was associated with residual stress and Ar incorporation into the Nb lattice. Strong {110} texture developed in the samples deposited at low bias voltages, while beyond U_B=−100 V a {111} texture became dominant. However, strong {111} texture was observed only with the thicker 3Nb coatings. Secondary electron microscopy investigation of the coating topography showed fewer defects in the thicker coatings. All coatings exhibited good corrosion resistance, with the thicker coatings clearly outperforming the thinner ones. Excessive bias voltages (U_B=−150 V) was found to lead to poor adhesion and loss of corrosion resistance.     

Alcohol tolerance in humans is enhanced by prior caffeine antagonism of alcohol-induced impairment.

The author tested the hypothesis that a history of drug-induced antagonism of alcohol impairment would enhance alcohol tolerance in humans. Groups of participants (N = 21) repeatedly performed a psychomotor task under different drug treatments: 0.65 g/kg alcohol, 4 mg/kg caffeine, or both drugs combined. Tolerance to a 0.65 g/kg alcohol dose challenge was then tested. Results showed that a history of combined alcohol and caffeine administrations increased alcohol tolerance compared with an exposure history to either drug alone. The findings contribute to the understanding of the complexities of polydrug use history and provide a useful model to examine how alcohol tolerance might be affected by a history of coadministration with other drugs (e.g., cocaine and nicotine). (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Different insights for improving part and system reliability obtained from exactly same DFOM “failure numbers”

Techniques for improving the reliability and maintainability of both nonrepairable and repairable items can be suggested by failure data analysis. It is shown that a given set of failure numbers leads to very different improvement strategies when the numbers are the times-between-successive-failures of one or more repairable items, rather than the times-to-failure of nonrepairable items. Since this should have been obvious more than 50 years ago, at the onset of formal reliability engineering activities, several reasons are proffered for the widespread and protracted misinterpretation of even the most basic—and simple!—conceptual and practical differences between nonrepairable and repairable items.     

HCMOS器件γ辐射损伤电路分析

本文对最基本的HCMOS器件(反相器和与非门)作了γ辐射损伤实验。通过器件性能变化,分析了γ辐射对电路的作用。     

参数三次B样条曲线的一种整体光顺方法

本文在能量法的基础上，提出了一种新的目标函数，给出了参数三次Ｂ样条曲线的一种新的整体光顺方法。利用这种方法得到的曲线不仅具有较小的应变能，而且曲率变化比较均匀，具有很好的光顺效果。该方法能推广到对曲面的光顺。     

Reaction between the tetragonal tungsten bronze niobate K2Sr4Nb10O30 and the perovskite Pb(Mg1/3Nb2/3)O3

The search for dielectric materials with a high dielectric constant and ′_r = ƒ(T) curves with a flat profile fitting the X7R specification is still ongoing. Promising results were obtained by mixing compounds with closely related structures, such as the tetragonal tungsten bronze (TTB) niobate K₂Sr₄Nb₁₀O₃₀ and the perovskite Pb(Mg_1/3Nb_2/3)O₃ (PMN). The present study, based on three methods of synthesis, explores the origin of the spreading out of the dielectric curves ′_r = ƒ(T). For the composition 10x K_0.2Sr_0.4NbO₃ (KSN) + (1 − x)Pb(Mg_1/3Nb_2/3)O₃ (PMN) with x = 0.3–0.6, the three synthesis methods provided similar characteristics and for the highest perovskite ratio (x = 0.3), the ′_r = ƒ(T) curve exhibits a flat profile. When lithium is used as a sintering agent, ′_r = ƒ(T) curves present a linear dependency with the temperature. These materials are also characterized by a structural and a microstructural inhomogeneity. Two phases TTB and perovskite type, different from KSN and PMN, are present after calcination and sintering, but not evenly distributed. The PbO loss during sintering also contributes to the evolution of the properties of the material.     

Theory of a novel voltage-sustaining layer for power devices

The theory of a novel voltage-sustaining layer for power devices, called a Composite Buffer layer (CB-layer for short) is proposed. The CB-layer can be implemented in several ways, one particular implementation is used here, which consists of alternating n- and p-type regions, that are parallel to the direction of the applied electric field. In the off-state, the fields induced by the depletion charges of both region types compensate each other to allowing the doping in both n-regions and p-regions to be very high without causing a reduction of the breakdown voltage. In the onstate the heavy doping ensures the voltage drop is very low and that the saturation current density high. A simple relationship between the specific on-resistance and R_on and the sustaining voltage V_B can be shown to be R_on=2.53 × 10⁻⁷bV_B^1.23 ωcm², where the breadth b (in μm) of each region is much smaller than the thickness W. The design method of the CB-layer is discussed in some detail. The simulation results are shown to be in perfect agreement with the theory. The structure has application to a wide variety of different power devices. An RMOST structure has been used to demonstrate the benefits of the technique in the paper, for which excellent performance is demonstrated.     

Flashover voltage characteristics of contaminated station insulators under temporary ac overvoltages in the ac system connected with a frequency converter station

According to the recent analysis results of temporary ac overvoltage in the ac system connected with a frequency converter station, large-magnitude over-voltages were confirmed to occur under some special system conditions. Most of the station insulators currently used cannot withstand such overvoltages according to an evaluation based on the data obtained earlier. The necessity of tests to be done to evaluate such performance more accurately was recognized. Both power frequency and switching impulse overvoltage flashover tests were made on contaminated insulators by the method well simulating the natural wetting condition. Switching impulse flashover voltage with the waveshape having a long wavefront time of 2 ms can be well correlated with the flashover voltage characteristics of temporary ac overvoltage. Higher flashover voltage characteristics were obtained by a clean fog test method compared with those obtained by equivalent fog test method.     

用于高压电容器的SrTiO3基陶瓷

报道ＳｒＴｉＯ３基陶瓷的制备方法和介电性质，给出了用此种陶瓷制成的高压电容器的试验结果，并对它位进行了讨论。     

航空油品高频/高压电脱水微观机理

设计并建立了一套高压电物理化学显微分析装置，为研究高压电物理化学领域的微观机理提供了一种新的技术途径。采用该技术，研究了胜利稠油经6％加氢裂解柴油稀释的原料油的高频／高压电脱水的微观机理。该原料的脱水率达96．7％，高于传统的电脱水方法。