淤泥软基爆炸固结试验研究

对爆炸效应在淤泥软基工程中的应用问题进行了探讨，并首次提出了爆炸在淤泥软基中的分界应力特征以及排水固结及破坏分区的基本模式。为采用动力加速对淤泥软基工程的处理，提供了试验依据，具有实用价值和指导意义。     

A concept for the generation of out-of-plane distortion from tailored FRP laminates

The phenomenon of thermally induced distortions in unsymmetrical laminates is well understood, and it may be shown that a square, unsymmetrical 0.90 laminate will tend to form two stable geometries with a snap-through phenomenon between them. This paper discusses laminates in which at each point the lay-up is symmetrical across the laminate mid-plane, but which still exhibit multiple stable geometries. The number of stable geometries can be controlled by the details of the lay-up from the minimum of two to, in principle, an unlimited number. In addition it will be shown how a similar process can be used to generate multiple stable stress states and geometries in unidirectional laminates. This paper represents a very preliminary experimental investigation of the design space available for such composite laminates. Possible applications of composites with multiple stable geometries are noted.     

Modeling of Material Deformation Kinetics in the Prefracture Zone

Based on the concept of complete stress–strain diagrams, we propose a new model describing the law of stress distribution in the prefracture zone in plastic materials in view of the type of the stressed state.     

高压对气井套管接头螺纹接触应力的影响研究

高温高压气井对螺纹密封性的要求要比油井更为严格。对于高压气井中的整个管柱,每一段处于不同的力学环境中,发生泄漏的可能性也不同,因此研究压力对气井套管接头螺纹接触应力的影响,对高压气井套管的合理使用尤为重要。利用弹塑性有限元分析方法,建立了API偏梯型螺纹套管接头的有限元模型,分析了气井压力对套管接头接触应力的影响,提供了研究压力对套管接头螺纹接触应力影响的方法。对于井口压力或井底压力超过34MPa的高压气井,应选用气密性良好的特殊螺纹接头,建议采用金属对金属的螺纹接头套管,以加强螺纹部位的连接强度和密封性能。     

起升中四腿落地式K型井架及底座的应力分析

针对在用四腿落地式K型井架在起升中井架与底座存在的问题,文章以JJ162/42-K型井架为例,采用I-DEAS有限元软件对起升过程中处于各角度时的井架及底座做了应力分析,并将其结果与两腿落地式K型井架进行了比较。分析表明,四腿落地式K型井架及底座在井架刚起升时,应力值较大,存在安全隐患。为了增强在井架起升过程中底座的安全性,建议在底座上井架2个铰支座之间加焊加强钢板,并加大井架前立柱铰支座的尺寸。     

覆盖层厚度对巷道周围应力分布的影响及巷道间相互作用的仿真

给出了覆盖层厚度对巷道周围应力分布的影响及巷道间相互作用的计算机仿真，用三维有限元法分析了在不同覆盖层厚度下巷道周围的应力分布和两个巷道之间不同距离下的相互作用。数值模拟表明了巷道周围应力分布和应力集中系数随覆盖层厚度增加的变化规律，找到了两巷道之间的距离的临界值，当两巷道间距离大于该临界值时，它们之间的相互作用消失。     

非饱和土的抗剪强度理论研究

从孔隙水的存在状态出发 ,围绕Bishop抗剪强度公式中存在的几个疑点展开讨论 .认为非饱和土中支配强度和变形的应力之所以不同 ,是因为非饱和土中存在一种性质与有效应力不同的应力———内部应力 ,它不传递 ,仅影响土的塑性变形 .同时还对Bishop ,Fredlund和卢肇钧提出的抗剪强度公式中的参数测试方法进行分析 ,指出 :各种抗剪强度理论在概念上都是相同的 ,其区别仅在于确定由吸力产生的那部分有效应力时采用的参数和测试方法不同     

用超声波技术测量螺栓轴向紧固应力

超声波速度会因材料中加载应力而产生微小的变化，这一现象特别适用于测量螺栓的轴向应力。根据螺栓的轴向应力与超声波传播时间变化率的关系，作者研究了一种可直接测量螺栓轴同应力的仪器。实验结果显示，本项技术十分适合现场的实际应用。     

COMPRESSION FATIGUE CRACK GROWTH BEHAVIOUR OF AN ALUMINIUM ALLOY: EFFECT OF OVERLOADING

Abstract— The behaviour of fatigue cracks in an Al-alloy under cyclic compression, either with or without overloads, was studied. For constant-amplitude compressive cycling, a non-catastrophic (saturation) character of the fatigue crack behaviour was confirmed, with the final depth of a crack depending on the applied load level. Single (tensile or compressive) intermittent overloads were shown to re-activate a previously arrested crack while reversed (tensile—compressive or compressive—tensile) ones were also shown to maintain continual fatigue crack extension under otherwise fully compressive cycling.     

氧化铝陶瓷缺口件循环疲劳及断裂机理

用实验方法研究了Ａｌ＿２Ｏ＿３陶瓷缺口试件在循环载荷作用下的疲劳寿命。结果表明，缺口导致的应力集中效应显著降低了循环疲劳寿命；若用缺口根部最大应力为应力水平，则不同缺口半径陶瓷试件具有相同疲劳断裂规律，说明陶瓷材料的疲劳集中系数和理论应力集中系数相同。本文还分析讨论了陶瓷材料的循环疲劳寿命表达式和循环疲劳断裂机理。