大型预焙铝电解槽使用碳化硅砖与普通碳砖复合块的探讨

碳化硅砖和碳化硅砖与普通碳砖复合侧块，在上世纪末期我国铝电解槽上开始推广应用。使用后各厂家普遍发现碳化硅砖及碳化硅砖与普通碳块复合侧块均出现不同程度的断裂、上抬和脱落现象，该文对断裂、上抬和脱落原因进行了分析，并提出了改进措施。     

蒸馏与减粘热联合装置的设备腐蚀及防护

介绍了锦西石化分公司南蒸馏与减粘热联合装置炼制辽河高酸值原油及带炼高硫进口油在 2 0 0～40 0℃范围内对设备、管线和阀门的腐蚀特点、腐蚀机理以及针对高温环烷酸腐蚀所采取的防护措施。通过试验和理论分析 ,提出了应用新材料和新工艺解决减粘后高温渣油系统的腐蚀及低温露点腐蚀的建议     

Forecasting Capillary Characteristics for Aluminum Nitride Ceramic ― Liquid Metal Systems

A test has been devised that allows one to determine the work of adhesion and wettability in a system composed of aluminum nitride ceramics with a liquid metal without the need for experimental examination. A correlation is examined between the work of adhesion on the one hand and that criteria or others on the other that have been proposed by various researchers. Forecasts are made for the work of adhesion and wetting angle for a series of metals that have not been examined previously. An experimental check has been made on the forecast adhesion activity for some elements.     

Oscillating Cup Viscosity Measurements of Aluminum Alloys: A201, A319 and A356

An oscillating cup viscometer was developed to measure the absolute viscosities of molten metals. Previous experiments established the capability of the apparatus to characterize the viscosities of molten nickel-based superalloys. However, modifications to the instrument and its theoretical analysis were required for reliable measurements on molten aluminum alloys, presumably due to their lower densities and lower viscosities. The theoretical literature for the fluid flow inside an oscillating cup is reviewed, and a working equation without any correction factor is developed for the improved viscometer. Some design parameters of the viscometer that directly affect the accuracy of viscosity estimation by using the working equation are discussed. A special vertical furnace was adopted to uniformly heat a longer cylindrical sample (10 mm inner diameter and 120 mm length) with a temperature difference of less than 2°C over the sample length. The measuring procedure was also improved to get more accurate motion parameters. It is estimated that the working equation and improved instrument provide an uncertainty of less than 4%. In addition, applications and experimental data are presented for pure aluminum and three aluminum alloys: A201, A319, and A356.     

Development of High Thermal Conductivity Aluminum Nitride Ceramic

AIN ceramics with densities varying from 3.18 to 3.30 g/cm³ and room-temperature thermal conductivities varying from 88 to 193 W/m K were produced. Different sintering conditions, packing powders, AIN powder sources, carbon additive, and sintering times were evaluated, and the key processing parameters which cause the differences in density and thermal conductivity were identified. SEM, TEM, and EDS were used to characterize the correlation between thermal conductivity, microstructure, and processing parameters. The important parameters which control the thermal conductivity of AIN ceramics are discussed.     

Crack growth in aluminium alloy sheet material under flight-simulation loading

Crack propagation tests were carried out on 2024-T3 sheet specimens to study the effects of omitting low-amplitude cycles from the gust-dominated TWIST load sequence (MiniTWIST) and the removal of small load ranges from the manoeuvre-dominated FALSTAFF load sequence (short FALSTAFF). In other tests high-amplitude loads of TWIST and MiniTWIST were truncated at different levels. The results are compared with data from similar test programmes, including crack initiation. Attention is paid to unstationary crack growth retardation and a transient retardation during initial crack growth started by an artificial crack.     

静态水热脱铝处理对HZSM-5分子筛的结构、酸性和催化性能的影响

开发了一种静态水热脱铝的方法。HZSM-5经此法处理后,正戊烷的裂解活性增加,脱氢和芳构化性能加强。可用改变处理温度的方法来控制脱铝的程度。用XRD和吡啶吸附红外技术进行了研究。HZSM-5分子筛催化剂性能的变化用非骨架铝产生的强L酸中心来解释。     

换热器防腐蚀方法介绍

文章对换热器的不同保护方法进行了介绍 ,重点讨论了渗铝、渗锌两种方法。在室温～ 80℃自来水和 3.5 %NaCl水溶液中 ,与碳钢基体相比 ,渗铝层的电位发生了反转 ,因而在针孔部位会形成大阴极小阳极的局面 ,易发生点蚀 ;而在相同条件下渗锌层不出现上述点蚀现象 ,更适宜在换热器的应用     

Failure of Al-Mg-Si alloys in bending

The bendability of two Al-Mg-Si heat-treatable alloys was studied and compared with the performance of a non-heat-treatable Al-Mg alloy. A semi-guided wrap-bend tester consistent with ASTM E290 was used to obtain minimum bend radii and produce consistent bend radii for analysis of fracture mechanisms. Bending failure in these alloys was based on a surface roughening, or orange peel, process where the outer surface grains separated and produced depressions on the surface of the material. These depressions acted as notches that increased local stresses and eventually caused failure. The fracture was intergranular in nature, with a jagged crack progressing through the thickness of the material. Several factors that affect the bendability of AA6xxx alloys are quantified in this study. Critical elements regarding natural aging, artificial aging, deformation, and composition are discussed. A parameter of specific interest is the inclusion of copper in these alloys. Copper was added in an effort to increase the artificial aging response of selected alloys. This is of particular importance in the automotive industry because artificial aging occurs during the painting process, but adequate time and temperature is not provided to fully strengthen the alloys. It is believed by some automotive manufacturers that the inclusion of copper can have a negative effect on formability and bendability.