环焊缝强度匹配对长输管道性能的影响

环焊缝强度匹配是天然气管道研究与应用的热点问题.介绍了焊接接头匹配性的概念,阐述了不等强匹配对长输管道极限载荷、韧性、残余应力、缺陷容限等的影响,最后提出了在长输管道环焊缝强度匹配领域需要解决的技术问题.     

真空铸造高强度C/Mg复合材料

本文介绍用真空铸造法制造抗拉强度超过1000MPa的高强度C/Mg复合材料。将T300纤维经C-Si-O梯度涂层处理后单向排布于型腔内,在真空下注入ZM-5合金液,凝固后即得C/Mg复合材料零件或试样。试样的抗拉强度在纤维体积分数为0.35时达1050MPa。本文讨论C-Si-O梯度涂层对获得高强度复合材料的作用。     

放置过滤器浇注系统的设计

综述了常用的网型、芯型、泡沫陶瓷过滤器的研究和应用情况。指出应根据过滤器类型，确定其在浇注系统中的安放位置并相应改变该处的结构和截面积，以便在使用过滤器净化金属的同时，保证充型速度不变。     

Processing of Yttria-Alumina Coated Silicon Nitride Slips by Slip Casting

Si₃N₄powders coated with 6 wt% Y₂O₃and 4 wt% Al₂O₃were prepared by coprecipitation. The resulting powders were dispersed in water at different pH values and with addition of various amounts of ammonium polyacrylate (NH₄PA) to produce 32 vol% slips. The influence of the amount of NH₄PA solution added and pH on the rheological properties of 32 vol% coated Si₃N₄slips were studied. In addition, the sintered density of cast samples was determined and related to the degree of slip dispersion. The adsorption of the NH₄PA on the coated particle surface was rather high and the surface became saturated near 0.86 mg/m²at pH 9.2. High NH₄PA concentrations (1.7–3 wt%) were necessary to obtain well dispersed 32 vol% coated Si₃N₄slips at pH 9.2. The best stabilization was obtained with the addition of 2.3 wt% NH₄PA; in this condition, the viscosity reached a minimum value of 35 mPa.s at 100 s^–1. The slip viscosity increased with increasing pH from 9.2 to 10.2. Slips with low viscosities gave a more dense packing of cast samples and consequently higher sintered density values.     

新世纪我国压铸业与国际接轨的思考

针对中国压铸行业的现状和存在的问题 ,以及当前的机遇和面临的挑战 ,论述了中国压铸工业进入 2 1世纪所面临的新形势及应采取的对策     

激光晶体Nd:YVO4的形貌及生长缺陷

本文报道了应用环境扫描电镜（ESEM）和同步辐射X射线白光形貌术对采用提拉法生长出的Nd:YVO4晶体进行的形貌及生长缺陷的分析,获得了该晶体的开裂表面的ESEM形貌像以及取自晶体肩部和中间部位的（001）面的同步辐射白光形貌像,观察到了位错、包裹物等缺陷,可为生长高质量的Nd:YVO4晶体提供重要的启示.     

连铸机油缸成套密封件国产化

本文论述了冶金行业中连铸机油缸密封件国产化的一些技术参数，同时也介绍了洪格尔型组合密封及夹布V型圈组合密封的使用特点。     

In-situ composite Cu-Cr contact cables with high strength and high conductivity

In order to develop a new type of contact cable with high strength and high electrical conductivity, Cu-Cr alloy series were selected as materials and Cu-Cr alloy castings were produced by means of directional solidification continuous casting (DSCC) process. The results show that the fibrillar strengthening phase, 13-Cr, orderly arranges among the copper matrix phase along the wire direction; and a microstructure of in-situ composite forms, which retains the basic property of good conductivity of the copper matrix and meanwhile obtains the strengthening effect of [3-Cr phase. The production technology as well as the mechanical property, electrical property, and synthetic property of the in-situ composite contact cables was discussed.     

Thermodynamic modeling of native point defects and dopants of GaN semiconductors

A thermodynamic modeling of GaN was carried out to describe the thermodynamic behavior of native defects, dopants, and carriers (free electrons and holes) in GaN semiconductors. The compound energy model (CEM) was used. An unintentionally doped GaN was taken as an example. Oxygen was introduced into the model as the unintentionally doped impurity, according to the practical experimental phenomena. The energies of component compounds in the model were defined based on the results of the ab initio calculations and adjusted to fit experimental data. The thermodynamic properties of the defects and the oxygen doped were calculated to show the facility of the model.     

基于织疵分析与管理专家系统的探讨

为了及时分析和有效控制织物的疵点,采用VFP 6.0建立了织疵分析与管理专家系统,介绍了系统的总体结构和数据存储形式、推理机制等内容。该系统能实现各种质量指标的统计与分析,对产生率高的疵点进行产生原因的诊断、推理,得出消除疵点的方法,并能准确地确定疵点的评分。结果表明,该系统通过在某工厂的实验,疵点的推断准确率为95%以上,节省疵点的分析时间三分之二,提高下机一等品率5%~10%。