Skeletal Isomerization and Inter—molecular Hydrogen Transfer Reactions in Catalytic Cracking

Bimolecular hydrogen transfer and skeletal isomerization the important secondary reac-tions among catalytic cracking reactions,which affect product yield distribution and product quality,Catalyst properties and operating parameters have great impact on bimolecular hydrogen transfer and skeletal isomerization reactions .Bimolecular hydrogen transfer activity and skeletal isomrization activity of USY-containing catalysts are higher thn that of ZSM-5-containing catalyst.Coke deposition on the active sites of catalyst may suppress bimolecular hydrogen transfer activity and skeletal isomer-ization activity of catlys in different degrees.Short raction time causes a decrease of hydrogen trans-fer reaction,but and increase of skeletal isomerization reaction compared to cracking reaction in catalytic cracking process.     

Augmentation of boiling heat transfer from horizontal cylinder to liquid by movable particles

This paper presents a series of experimental results on a passive augmentation technique of boiling heat transfer by supplying solid particles in liquid. A cylindrical heater 0.88 mm in diameter is placed in saturated water, in which a lot of mobile particles exist, and the nucleate and film boiling heat transfer characteristics are measured. Particle materials used were alumina, glass, and porous alumina, and the diameter ranged from 0.3 mm to 2.5 mm. Particles are fluidized by the occurrence of boiling without any additive power, and the heat transfer is augmented. The maximum augmentation ratio obtained in this experiment reaches about ten times the heat transfer coefficient obtained in liquid alone. The augmentation ratio is mainly affected by the particle material, diameter, and the height of the particle bed set at no boiling condition. The augmentation mechanism is discussed on the basis of the experimental results. © 2001 Scripta Technica, Heat Trans Asian Res, 31(1): 28–41, 2002     

建筑墙体表面传热系数辨识研究

对实验房间南向墙体内表面中心区域的换热过程进行实验，发现当风速在0－5．5m/s之间时，表面传热系数在8－18W（m^2.K）之间波动，而风向对墙体表面传热系数影响不大；用辅助变量法分析墙体表面传热过程，并结合实验推导出墙体表面传热系数。模型的预测结果与实测结果吻合良好。     

A continuum-based modeling of MEMS devices for estimating their resonant frequencies

A continuum-based modeling of coupled electrostatics-structure interactions is presented for the frequency computations of MEMS devices. The present general formulation of electrostatics accounting for free space is validated first by specializing it to one-dimensional uniform motion of conducting surfaces and comparing the resulting electrostatics to conventional lumped models. The general coupled electrostatics-structure interactions are then applied for the prediction of resonant frequencies of MEMS devices due to bias-voltage changes and temperature variations. Comparisons of predicted resonant frequencies obtained by the present coupled electrostatics-structure interaction models with experimental results available in the literature demonstrate that the proposed continuum-based interaction modeling yields high-confidence predictions of resonant frequencies of MEMS devices.     

The Clausius inequality corrected for heat transfer involving radiation

The objective of this paper is to prove that the Clausius inequality must be re-stated to have general applicability for heat transfer involving radiative fluxes. The integrand (đQ/T) of the Clausius expression applies to heat conduction and convection, but does not hold for most radiative transfer scenarios, with the exception of reversible infinitesimal net blackbody radiation transfer. In other cases involving radiative transfer, the equality holds for a cycle even though irreversible heat addition by radiative transfer occurs. This is without the erroneous presumption of entropy destruction anywhere in the cycle. Thus, the Clausius inequality indicates reversibility for a cycle that includes an irreversible process. Further, in some radiative cases the quantity đQ/T, where T is the boundary temperature, is not the entropy transfer at the system boundary, and in fact, primarily represents entropy production within the system. It is also clear that in another case considered, the quantity đQ/T had no physical meaning whatsoever. Consequently, the Clausius expression has been re-stated so that it is applicable to cycles with processes involving any form of heat transfer. A new integrand (đQ_cc/T + đS_Net,Rad) is presented, allowing the Clausius inequality to generally apply to all heat transfer scenarios. The work in this paper emphasizes the need to re-state other fundamental equations allowing applicability to all heat transfer processes, and draws attention to the unique character of radiative entropy calculations.     

Cooling and Solidification of Melted Drops in an Immiscible Cooling Medium

The cooling and solidification of melted drops during their movement in an immiscible cooling medium is widely employed for granulation in the chemical industry, and a study of these processes to provides a basis for the design of the granulation tower height and the temperature of the cooling medium is reported. A physical model of the cooling and solidification of the drop is established and the numerical calculation is performed. The influences of the key factors in the solidification, i.e., Bi number, drop diameter, temperature of the cooling medium, etc. are presented. The cooling and solidification during wax granulation in a water‐cooling tower and during urea granulation in an air‐cooling tower (spraying tower) are described in detail. Characteristics of the solidification and temperature distribution within the particle at different times are shown. The model and calculations can be used for structure design of the granulation tower and optimization of the operation parameters.     

Evaluating the transfer of technology between application domains: a critical evaluation of the human component in the system

Technology can take many forms from the development of sophisticated electronics to the application of basic procedural principles. Technology transfer can also take several forms, however, in this case, it is the transfer of technological principles between application domains that is of primary interest. This paper presents a framework (the Five ‘M’s framework) that can be used to consider the likely success of technology transfer. The framework is based upon a sociotechnical system approach. The framework is illustrated with an evaluation of the introduction of intelligent cruise control into motor vehicles. It is argued that this is a technological concept first developed as an aerospace application in the form of the autopilot. In this case, it is argued that the transfer of this technology in its current form may potentially compromise safety.     

Host/guest complex of Me-β-CD/2,2-dimethoxy-2-phenyl acetophenone for initiation of aqueous photopolymerization: Kinetics and mechanism

Methylated-β-cyclodextrin (Me-β-CD) was used to complex the photoinitiator, 2,2-dimethoxy-2-phenyl acetophenone (DMPA), yielding a water-soluble host/guest complex. The comparative studies demonstrated that the Me-β-CD complexed DMPA exhibited a high photoreactivity identical to the uncomplexed DMPA, while the CD complex obviously influenced the products of primary photolysis of DMPA and the photopolymerization kinetics due to the steric effect of CD on the subsequent initiation reactions. The photopolymerization rate of acrylamide can be described by the equation: R_p=K[2a]^0.62[M]^1.37[I]^0.5[Me-β-CD]⁰. The mechanism of polymerization was also discussed.