Fe calculations of stress fields from cracks located at the fusion line of weldments

This paper investigates the stress fields for a crack located at the fusion line of a weldment. The strength mis-matching and the size of the HAZ were varied, and the corresponding distribution of the maximum principal stress was examined. The weld metal strength was globally overmatched with respect to the base material, but locally over- and undermatched with respect to the heat affected zone. Three cases of mis-match were compared, and it was found that reducing the strength of the HAZ lowered the maximum principal stresses.     

对梁,底组合步进式加热炉半热滑轨的改进实践

介绍了间断式半热滑轨的研制和应用过程，以及经过节能技术改造，用新型半热滑轨代替老式滑轨的使用。实践表明，不但解决了以往的水梁漏水的问题，而且使线Ｃ级品率提高了３．３９％，每年可增产３５００ｔ线材，吨钢热涌单耗降低０．１４ＧＪ，年创经济效益２３９万元。     

高能球磨AL─Cu合金固态合成反应研究

采用扫描电镜、能谱分析、Ｘ射线衍射和示差扫描量热分析研究了具有较大负混合焓的Ａｌ＿ｘＣｕ＿（１－ｘ）对称扩散系合金的高能球磨固态合成反应。高能球磨时组元晶粒细化达纳米级，造成纳米晶界亚互溶，为室温固态合成反应创造了条件，球磨强度对反应进程影响显著，在ｘ＝０．３～０．７范围内仅形成一种金属间化合物。     

高产高效综采工作面几个技术问题的探讨

在总结东北区综采工作面生产经验的基础上，论述了实现高产高效综采工作面的有关技术问题和解决方法。     

Surface treatment for adhesive-bonded joints by excimer laser

In this work a treatment for surface preparation to improve mechanical resistance in adhesive bonding of plastic composites reinforced with fibres and metallic material, has been performed using an excimer laser. The following couplings have been selected to reproduce joints commonly used in the aerospace and automotive industry: CFC (carbon fibre composite) with CFC, CFC with Al 2024T3, Al 99% with Al 99%, GFC (glass fibre composite) with zinc-coated sheet in low carbon steel FeP01. The surfaces have been prepared using an excimer laser, adopting several values of laser parameters. The obtained surfaces have been examined by optical and scanning electron microscope: comparative measures of wetting and roughness have been performed to obtain an accurate characterisation and to select the proper finishes suitable to improve the mechanical resistance of the joints. The results obtained show that laser treatment always improves the final resistance of the joint; notable increases, and no significant surface damages have been highlighted. Better results have been obtained with the Al 99% with Al 99% joints which, with a low number of pulses treatment, have shown an increase of mechanical resistance up to the 70%.     

基于HLA的水中兵器仿真系统框架

为了解决我国水中兵器传统的仿真系统,局限于某些参数的数学仿真和部分半实物仿真,没有实现系统化、可视化,实时化,文章提出一种采用高层体系结构（HLA）作为分布交互的仿真体系框架,通过对水中兵器对抗系统仿真建模,解决了不同仿真应用之间的集成问题,较好地满足仿真系统的可视化、可操作性、强实时性及强交互性等要求。该仿真系统可以为水中兵器作战研究和武器装备论证提供仿真试验环境,检验装备各项战略战术指标,并为装备研制和战略战术决策提供依据,具有很高的实用价值。     

应用事件驱动和有限状态机实现多路数据采集

设计与实现一种基于8位单片机的多路数据采集节点。在硬件上节点由C8051F340单片机,数据采集电路和网络通信电路构成。在节点的软件设计上,设计一种事件驱动结合有限状态机的方式,以实现多路数据实时,高效、智能的采集。事件驱动模型完成数据采集的控制;实际的数据采集功能则由有限状态机完成。依据多路数据间的相关性最为判断,选择Mealy型有限状态机或Moore型有限状态机。在软件结构上具有模块之间耦合度低,逻辑清晰和高扩展性的特点。经实践证明,基本满足设计要求。     

高可用性舰船网络系统研究

随着舰船信息系统网络化应用的不断增加,信息系统对舰船网络的依赖性也在不断增强,这对网络持续提供服务的高可用能力提出了更高的要求。鉴于目前舰船网络系统的可用性不能满足舰船信息业务对数据中断恢复时间所提出的要求,将最新的商用高可用性IRF2技术引入舰船网络系统,提出了一种新的舰船网络系统方案。该方案采用双交换机堆叠及跨交换机链路聚合的方式实现网络的网关冗余和路径冗余,简化了网络的逻辑结构,提高了整网的故障恢复时间。通过搭建的原型系统对方案的重要参数进行了测试,结果表明：相比于目前的舰船网络,该方案提升了网络效率,并将故障倒换时间从秒级缩短到了50ms级。     

高压电气设备支架串联体系地震响应半解析法

通过论述高压电气设备支架串联体系地震响应半解析法的运算过程,说明地震响应半解析法对于电力系统防震工作的帮助。     

110kV高压开关二次储能回路改进

针对110kV联兴站110kV高压开关二次储能回路设计存在的缺陷,提出改进意见,并提出故障防范措施。