Suggestions for the quantitative X-ray microanalysis of thin sections of frozen-dried and embedded biological tissues

When a microregion in a thin section of frozen-dried and embedded tissue is analysed by the conventional electron-probe X-ray continuum-normalization method, the measured quantity is in mmol of element per kg of embedded specimen. As each microregion contains an unknown amount of embedding medium, this quantity generally lies indeterminately somewhere within the wide range between mmol of element per kg of hydrated tissue and mmol of element per kg of dehydrated tissue. However, if a ‘tag’ element is incorporated in the embedding medium, the contribution of the medium to the local continuum count in each probed field should be measurable, and the X-ray data may then unambiguously yield mmol of element per kg of dehydrated tissue. This result should not be affected by shrinkage on freeze-drying or by incomplete replacement of water by embedding medium. The same X-ray data can additionally provide estimates of mmol of element per unit volume, mmol of element per kg of hydrated tissue and local dry-mass fraction. However, these estimates are subject to errors due to tissue shrinkage, incomplete replacement of water and beam damage.     

Electrical conductivity of ferroelectric sodium vanadate,rubidium vanadate,cesium vanadate and their solid solutions

The d.c. electrical conductivity of sodium vanadate, rubidium vanadate, cesium vanadate and their solid solutions sodium-rubidium vanadate and sodium-cesium vanadate were studied by a two-probe method in the temperature range covering their transition points. The electrical conductivity shows sharp change at the phase transition temperature of these materials. In NaVO₃, RbVO₃ and CsVO₃, increase in d.c. conductivity is observed in the ferroelectric region while nonlinearities are observed above transition temperatures. In solid solutions, the activation energy in the paraelectric state is higher than that in the ferroelectric state and depends upon sodium concentration.     

A One-Dimensional Nonlocal Damage-Plasticity Model for Ductile Materials

This paper presents a new 1-D non-local damage-plasticity deformation model for ductile materials. It uses the thermodynamic framework described in Houlsby and Puzrin (2000) and holds, nevertheless, some similarities with Lemaitre’s (1971) approach. A 1D finite element (FE) model of a bar fixed at one end and loaded in tension at the other end is introduced. This simple model demonstrates how the approach can be implemented within the finite element framework, and that it is capable of capturing both the pre-peak hardening and post-peak softening (generally responsible for models instability) due to damage-induced stiffness and strength reduction characteristic of ductile materials. It is also shown that the approach has further advantages of achieving some degree of mesh independence, and of being able to capture deformation size effects. Finally, it is illustrated how the model permits the calculation of essential work of rupture (EWR), i.e. the specific energy per unit cross-sectional area that is needed to cause tensile failure of a specimen.     

水库突发事件应急预案研究现状与关键技术初探

水库突发事件应急预案是大坝风险管理中非常重要的一个环节,是降低水库大坝风险的非工程措施.本文总结了国内水库突发事件应急预案的研究现状,并结合我国实际国情,初步提出了开展应急预案的关键技术,供大坝安全管理及科研人员参考.     

降低气体悬浮焙烧炉焙烧过程中Al_2O_3粒度破损的措施

为了降低气体悬浮焙烧炉焙烧过程中Al_2O_3粒度的破损,对气体悬浮焙烧炉焙烧过程中氧化铝粒度的影响因素进行了分析,提出了降低粒度破损的一些措施。     

Understanding and Modeling the Effect of Surfactants in Enhanced Particle Removal from Surfaces in Aqueous Media

The removal of particulate contamination is a critical issue for many manufacturing processes. It is particularly critical to the electronics industry in which small pieces of microscopic debris remaining after chemical mechanical planarization (cmp) using submicron polishing particles can cause device failure. One way to enhance particle removal following the cmp process is to utilize surfactants. Recent research has shown ways to model the effect of surfactants on enhanced particle removal. However, previous research has not demonstrated the effect of ionic strength on enhanced particle removal associated with surfactant use. Past research has also not shown the combined effects of ionic strength and surfactant concentration on enhanced particle removal using surfactants. This article summarizes the parameters affecting particle removal, and it provides data and analysis on the effect of ionic strength as well as the combined effects of ionic strength and surfactant concentration on particle removal following cmp processing.     

Oxygen content of the fixative is important in the interpretation of the ultrastructure of ischaemic myocardium

Isolated rat hearts were subjected to 15, 45, or 60 minutes of global ischaemia and then fixed by perfusion at 37°C with glutaraldehyde containing various amounts of oxygen. This either had been bubbled with 100% oxygen (PO₂ 620 mm Hg) or with 100% nitrogen (PO₂ 40 mm Hg) immediately before use, or it had been routinely prepared and stored exposed to atmospheric oxygen (PO₂ 245 mm Hg). The ultrastructure of myocytes and endothelial cells subjected to 15 minutes of ischaemia was not affected by the treatment of the fixative. However, when the tissue subjected to longer periods of ischaemia was fixed with routinely prepared or oxygen-bubbled glutaraldehyde, ultrastructural changes characteristic of reoxygenation damage were uniformly evident in both the microvasculature and myocytes. These qualitatively distinct changes included mitochondrial swelling, cell swelling, endothelial bleb formation, and narrowing of capillary lumina. These abnormalities were not observed in tissue fixed with nitrogen-bubbled glutaraldehyde. These findings indicate that deliberate steps should be taken to reduce or eliminate dissolved oxygen from the fixatives used to study ischaemic tissues. Otherwise artefactual reoxygenation damage in vitro may occur and make valid ultrastructural interpretation difficult or impossible.     

Self-Irradiation Cascade Simulations in Plutonium Metal: Model Behavior at High Energy

The Modified Embedded Atom Method model for Pu metal is revised so that it more accurately captures the behavior of the Ziegler-Biersack-Littmark model of ion-ion interactions. Two revision are tested with somewhat different stiffnesses in the 2-1000 eV range. The revised models show higher damage levels at 20 KeV than an earlier model, suggesting that the behavior of the models above 100 eV is dominating damage production, at least in the earlier stages of the cascade. Work was performed at Los Alamos National Laboratory under the auspices of the US Department of Energy, under contract DE-AC52-06NA25396.     

Pool boiling on a superhydrophilic surface

Titanium Dioxide, TiO₂, is a photocatalyst with a unique characteristic. A surface coated with TiO₂ exhibits an extremely high affinity for water when exposed to UV light and the contact angle decreases nearly to zero. Inversely, the contact angle increases when the surface is shielded from UV. This superhydrophilic nature gives a self-cleaning effect to the coated surface and has already been applied to some construction materials, car coatings and so on. We applied this property to the enhancement of boiling heat transfer. An experiment involving the pool boiling of pure water has been performed to make clear the effect of high wettability on heat transfer characteristics. The heat transfer surface is a vertical copper cylinder of 17 mm in diameter and the measurement has been done at saturated temperature and in a steady state. Both TiO₂-coated and non-coated surfaces were used for comparison. In the case of the TiO₂-coated surface, it is exposed to UV light for a few hours before experiment and it is found that the maximum heat flux (CHF) is about two times larger than that of the uncoated surface. The temperature at minimum heat flux (MHF) for the superhydrophilic surface is higher by 100 K than that for the normal one. The superhydrophilic surface can be an ideal heat transfer surface. Copyright © 2002 John Wiley & Sons, Ltd.     

HCMOS器件γ辐射损伤电路分析

本文对最基本的HCMOS器件(反相器和与非门)作了γ辐射损伤实验。通过器件性能变化,分析了γ辐射对电路的作用。