A two-stage algorithm for identification of nonlinear dynamic systems

This paper investigates the two-stage stepwise identification for a class of nonlinear dynamic systems that can be described by linear-in-the-parameters models, and the model has to be built from a very large pool of basis functions or model terms. The main objective is to improve the compactness of the model that is obtained by the forward stepwise methods, while retaining the computational efficiency. The proposed algorithm first generates an initial model using a forward stepwise procedure. The significance of each selected term is then reviewed at the second stage and all insignificant ones are replaced, resulting in an optimised compact model with significantly improved performance. The main contribution of this paper is that these two stages are performed within a well-defined regression context, leading to significantly reduced computational complexity. The efficiency of the algorithm is confirmed by the computational complexity analysis, and its effectiveness is demonstrated by the simulation results.     

A fictitious domain decomposition method for the solution of partially axisymmetric acoustic scattering problems. Part I: Dirichlet boundary conditions

We present a fictitious domain decomposition method for the fast solution of high‐frequency acoustic scattering problems characterized by a partially axisymmetric sound‐soft scatterer. We apply this method to the solution of various mockup submarine problems, and highlight its computational advantages and intrinsic parallelism. Copyright © 2002 John Wiley & Sons, Ltd.     

信号时域积分性质的一个推广应用

对信号进行运算（卷积运算，傅氏变换，拉纸变换）时，应用时域积分性质，得出由函数导数的运算式求取原函数的相应运算结果的一般性计算公式，使时域积分性质的应用得到推广。     

X射线衍射线形Fourier变换

采用计算机辅助实验技术，研究X射线衍射线开在仪器宽化修正过程中Fourier系数变化的规律及其影响，结果表明，只要实测线形接近Gauss 分布，Fourier变换就会导致弯勾效应；Forier变换可引起真实线形的尾部波动及大于实际值的宽化，引入边界条件可予以消除，Kα双线形经过Fourier变换后，Fourier纱数与真实Fourier系数存在着一定的差异。通过真实线形的Fourier变换可以修正。     

薄板坯连铸连轧工艺对铌微合金化高强度钢组织和性能的影响

首先建立薄板坯连铸连轧工艺的试验室模拟技术，并运用该模拟技术，研究薄板坯连铸连轧工艺(CSP)和传统板坯再加热工艺(TRP)两种工艺对铌微合金化高强度钢的显微组织和力学性能的影响。研究结果表明：CSP钢的晶粒细化效果不如TRP钢，两者的平均铁素体晶粒尺寸分别为8．17μm和6．30μm。在CSP试验钢板中铌的析出量较大，特别是在铁素体中细小颗粒的铌的析出物较多，沉淀强化效果较强。CSP试验钢的σ0.5和σb分别较TRP工艺低约40MPa和约25MPa，同时其低温冲击韧性较好，FATT温度较低。     

钛化物在铝熔体中的沉淀现象

为了研究导致细化衰退的钛化物沉淀现象，以中间合金为细化剂对工业纯铝进行了细化处理，得到了不同沉淀时间的沉淀试样，利用金相、SEM等技术分析了试样底部沉淀物的显微组织．结果表明：加入中间合金后，试样均存在明显的软化物沉淀现象，且沉淀物中既有TiC(TiB2)化合物，也有TiAl3化合物；沉淀物中的TiAl3与原中间合金中的TiAl3形态一致，说明原中间合金中的一些TiAl3化合物在没有分解完全时就已沉到试样底部；AlTiC中间合金比AlTiB中间合金的钛化物沉淀倾向明显．     

On the relationship between parity space and approaches to fault detection

Parity space approach and H₂ approach are two important fault detection approaches. This paper studies the relationship between these two approaches, which reveals frequency domain characteristics of the optimal solution of the parity space approach on the one side and provides a numerical solution of the H₂-optimal design of residual generators on the other side.     

A fictitious domain decomposition method for the solution of partially axisymmetric acoustic scattering problems. Part 2: Neumann boundary conditions

We present a fictitious domain decomposition method for the fast solution of acoustic scattering problems characterized by a partially axisymmetric sound‐hard scatterer. We apply this method to the solution of a mock‐up submarine problem, and highlight its computational advantages and intrinsic parallelism. A key component of our method is an original idea for addressing a Neumann boundary condition in the general framework of a fictitious domain method. This idea is applicable to many other linear partial differential equations besides the Helmholtz equation. Copyright © 2003 John Wiley & Sons, Ltd.     

结构-波浪-海床耦合系统中大圆筒结构的波压力响应

以沉入式大圆筒结构为对象，通过设计随机波浪水槽实验，测取了在单筒和连续筒两种结构型式、两种沉入深度和两种波谱输入下结构表面的动波压力分布。波面高度以及波压力历程均在领域进行分析。通过计算结构表面沿高程和沿环向的波压力谱及波压力传递函数，将单筒实测结果与基于线性绕射理论的解析解进行了比较，同时也详细对比了两种结构型式下的实测结果。文中汇报了在研究中获得的新发现及进行的相应分析，特别是在结构——波浪——海床动力相互作用下对波压力响应机理以及针对连续筒的研究，可为工程应用提供有价值的参考。     

A frequency domain approach to fault detection in sampled-data systems

This paper deals with fault detection problems in sampled-data (SD) systems. A tool is first introduced for the analysis of intersample behavior of SD systems in the frequency domain from the viewpoint of fault detection and isolation. Based on it, a direct design approach of fault detection systems for SD systems is proposed, and further the problem of full decoupling from unknown disturbances is studied.