Surface hydrolysis of filaments based on poly(trimethylene terephthalate) spun at high spinning speeds

The surface alkaline hydrolysis of fibers made from poly(trimethylene terephthalate) (PTT) was studied after extruding the polymer at high spinning speeds from 2000 to 6000 m/min and heat setting in the range of temperatures from 100 to 180°C. Fiber weight loss increased with an increasing heat‐setting temperature but it was also dependent on the spinning speed. Some of the partially hydrolyzed fibers had a well‐developed, hydrophilic surface, and pore size in the range of 0.69 to 1.20 μm. The optimum reaction and morphological conditions for increasing porosity in PTT fibers depends on spinning speed and heat‐setting temperature. A temperature of 180°C is the upper limit for heat‐setting PTT filaments but seems to be the most effective for making porous fibers. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1724–1730, 2004     

钢领化学镀Ni－P－PTFE工艺实践

提出细纱机钢领化学镀Ｍ—Ｐ—ＰＴＦＥ工艺及其维护管理。Ｎ—Ｐ—ＰＴＦＥ复合镀层具有优良的润滑、耐磨、耐蚀性能，硬度高、摩擦系数小。     

直纺PET与切片纺COPET的FDY海岛丝生产技术

对纺丝温度、冷却条件进行了详细的讨论。结果表明:适合的PET纺丝温度,PET的黏度降在0.06以内,有效的吹风和上油条件可纺出优良产品。     

Nitrogen fertilizer use in rainfed agriculture

Agronomic efficiency (AE) is defined as the increase in economic yield of a crop per unit fertilizer applied. Components of AE are physiological efficiency and apparent recovery fraction. The latter can be further separated into uptake efficiency and availability index. Ways to increase the nitrogen fertilizer use efficiency in rainfed agriculture through fertilizer management are discussed.     

淀粉-MMA接枝共聚物的半干法合成新工艺

以硝酸铈铵(CAN)为引发剂,采用固相半干法合成了玉米淀粉(CS)接枝甲基丙烯酸甲酯(MMA)共聚物。考察了含水量、反应体系的酸性、反应时间与温度、MMA单体和引发剂CAN用量等因素对接枝共聚反应的影响。结果表明,体系含水质量分数为35%左右,CAN用量为CS质量的1.5%～3%,反应温度在40～50℃,反应时间为0.5h左右,可得到接枝率、接枝效率和单体转化率均较高的接枝共聚物。     

采用加压-真空两段热缩聚法制备中间相沥青炭纤维的原料

以深度裂解石油渣油为原料，采用两段热缩聚法可制得软化点为268℃，可编性良好的中间相沥青。本文详细考察了温度，时间对中间相沥青软化点，可编性，中间相沥青形态及碳化收率的影响，并初步探讨了两段热缩聚反应的机理。研究结果表明反应温度，时间对中间相沥青的结构和性能影响较大，选择适宜石油渣油，采用加压－真空两段热缩聚法，调整反应条件，可制得可纺性良好的中间相沥青。     

3000m~3/h排烟循环流化床脱硫工艺中试实验研究

介绍了采用真实烟气的 30 0 0m3 /h排烟循环流化床烟气脱硫工艺 (CFB FGD)及其中间试验装置 ,通过实验研究了钙硫摩尔比 (Ca/S)、近绝热饱和温度差 (ΔT)、烟气湿度、喷水量、入口SO2 浓度、浆液雾化质量、脱硫灰循环等对脱硫效果的影响。实验表明 ,CFB FGD工艺在停留时间小于 6s、烟气流速v =4— 6m/s、Ca/S =1.2、ΔT =10— 12℃时可实现高达 90 %的脱硫效率。     

纺丝组件三甘醇清洗系统的改造

介绍了三甘醇 (TEG)清洗系统的工艺流程和所存在的主要问题是自然冷却时间太长和TEG蒸气泄漏。提出该系统的改造方案为变自然冷却为强制风冷 ,把清洗釜盖的密封改为榫槽式 ,使改造后的TEG清洗系统达到了国际通用的HSE(健康、安全、环境 )的标准 ,缩短了TEG清洗后的冷却时间 ,罐体密封更加严密 ,清洗快捷、方便     

Breakthrough and Sulfate Conversion Analysis during Removal of Sulfur Dioxide by Calcium Oxide Sorbents

Sorption of sulfur dioxide (SO₂) was carried out on calcium‐based sorbents under dynamic conditions in a fixed bed. The experimental conditions were reaction temperature (700 to 1000°C), SO₂ concentration (1000‐10 000 ppm), sorbent particles size (1 to 2 mm) and the types of sorbents (hydroxide or carbonate). The sorption process was found to be effective at low concentration levels (less than 10 000 ppm) as the breakthrough time significantly decreased with increase in concentration. The maximum removal of SO₂ was observed at a reaction temperature of 950°C. The hydroxide‐based sorbents of relatively smaller particle size were found to exhibit superior sorption performance in terms of longer breakthrough time and higher sulfate conversion. A mathematical model developed, assuming a porous structure of the sorbent materials, attributed the low sulfation conversion during SO₂ sorption due to a pore diffusion mechanism.     

国产短程纺牵联合机纺制烟用聚丙烯丝束的工艺研究

用国产SLHP001短程纺牵联合机和SLHP 101丝束加工联合机,通过选择合理生产工艺,着眼于提高纤维的刚性和膨松性,研制出了高质量的烟用聚丙烯丝束。不加胶粘剂成型的滤棒(120mm),圆周稳定,硬度达到88%—89.5%,吸阻为3.2-3.4kPa,产出率达到125万支/t,比国内同类产品高15—20万支/t。