Wear and Creep Characteristics of a Carbon‐Derived Si3N4/SiC Micro/Nanocomposite

In the presented work some properties of a recently developed Si₃N₄/SiC micro/nanocomposite have been investigated. The material was tested using a pin on disc configuration. Under unlubricated sliding conditions using Si₃N₄ pin at 50 % humidity, the friction coefficient was in the range of 0,6 ‐ 0,7. The reduction of humidity resulted in a lower coefficient of friction, in vacuum the coefficient of friction had a value of about 0,6. The wear resistance in vacuum was significantly lower then that in air. The wear patterns on the Si₃N₄+SiC disc revealed that mechanical fracture was the wear controlling mechanism. Creep tests were realized in four point bending configuration in the temperature interval 1200‐1400 °C at stresses 50,100 and 150 MPa and the minimal creep deformation rate was established for each stress level. The activation energy, established from the minimal creep deformation had a value of about 360 kJ/mol and the stress exponent values were in the range of 0.8‐1.28. From the achieved stress exponents it can be assumed that under the studied load/temperature conditions the diffusion creep was the most probable creep controlling mechanism.     

Phase behavior,density, and crystallization of polyethylene in n‐pentane and in n‐pentane/CO2 at high pressures

The phase behavior and volumetric properties of polyethylene (PE) in solutions of n‐pentane and n‐pentane/CO₂ were studied in a temperature (T) range of 370–440 K at pressures up to 60 MPa. Measurements were conducted with a variable‐volume view‐cell system equipped with optical sensors to monitor the changes in the transmitted light intensity as the P or the T of the system was changed. Lower‐critical‐solution‐temperature‐type behavior was observed for all of the liquid–liquid (L–L) phase boundaries, which shifted to higher pressures in solutions containing CO₂. The solid–fluid (S–F) phase boundaries were investigated over a P range of 8–54 MPa and took place in a narrow T range, from 374 to 378 K in this P interval. The S–F phase boundary showed a unique feature in that the demixing temperatures showed both increasing and decreasing trends with P depending on the P range. This was observed in both the PE/n‐pentane and PE/n‐pentane/CO₂ mixtures. The density of these solutions were measured as a function of P at selected temperatures or as a function of T at selected pressures that corresponded to the paths followed in approaching the phase boundaries (S–F or L–L) starting from a homogeneous one‐phase condition. The data showed a smooth variation of the overall mixture density along these paths. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2201–2209, 2003     

A Relational Model of Workplace Victimization: Social Roles and Patterns of Victimization in Dyadic Relationships.

This article proposes a model of the ways in which dyadic interactions between employees who occupy 1 of 4 archetypal social roles in organizations can lead to either episodic or institutionalized patterns of victimization. The model shows how the occurrence of victimization involving these 4 role types is influenced by organizational variables such as power differences, culture, and access to social capital. The model integrates behavioral and social structural antecedents of victimization to develop a relational perspective on the dynamics of harmful behavior in the workplace. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

具有阻力特性材料的σ_f－σ关系及一种新的阻力曲线测定方法

通过对相变增韧陶瓷及一种可切削玻璃－陶瓷动态疲劳（恒应力速率）试验中高应力速率区断裂应力下降现象的理论分析，发现这种现象与材料的阻力特性（Ｒ－ｃｕｒｖｅ）密切相关。确立的σ_ｆ－σ理论关系能够很好地描述整个应力速率区间内的动态疲劳试验结果。高应力速率区σ_ｆ－σ在双对数坐标下为负斜率直线，直线斜率为（ｍ为阻力曲线ＫＲ＝ｋ（△ａ）~ｍ的指数），断裂主要由材料阻力行为控制；低应力速率区，σ_ｆ－σ在双对数坐标下为正斜率直线，直线斜率为　（ｎ为应力腐蚀指数），断裂主要由材料应力腐蚀行为控制。建立了测定材料阻力特性的一种新方法，分别用这种方法及压痕／弯曲方法对一种可切削玻璃－陶瓷的阻力特性进行了实验测定，两种方法所得结果有很好的一致性。     

Processing of Yttria-Alumina Coated Silicon Nitride Slips by Slip Casting

Si₃N₄powders coated with 6 wt% Y₂O₃and 4 wt% Al₂O₃were prepared by coprecipitation. The resulting powders were dispersed in water at different pH values and with addition of various amounts of ammonium polyacrylate (NH₄PA) to produce 32 vol% slips. The influence of the amount of NH₄PA solution added and pH on the rheological properties of 32 vol% coated Si₃N₄slips were studied. In addition, the sintered density of cast samples was determined and related to the degree of slip dispersion. The adsorption of the NH₄PA on the coated particle surface was rather high and the surface became saturated near 0.86 mg/m²at pH 9.2. High NH₄PA concentrations (1.7–3 wt%) were necessary to obtain well dispersed 32 vol% coated Si₃N₄slips at pH 9.2. The best stabilization was obtained with the addition of 2.3 wt% NH₄PA; in this condition, the viscosity reached a minimum value of 35 mPa.s at 100 s^–1. The slip viscosity increased with increasing pH from 9.2 to 10.2. Slips with low viscosities gave a more dense packing of cast samples and consequently higher sintered density values.     

复相材料的循环变形行为

对三种组织状态的F-M复相钢进行了对称和非对称循环加载条件下的形变研究.结果表明,双相钢的循环变形行为,不仅与组织中位错组态的演变过程有关,同时也受循环载荷大小、类型以及加载方式所影响.分析表明,双相钢的循环硬化、软化行为主要受控于两个基本过程,即循环变形时位错组态演变的物理过程和相间分载应力的转嫁、相间残余应力变化的力学过程.     

基于相关性的人机系统可靠性模型

本文在剖析人机系统中操作者行为特征的基础上,考虑到操作者行为的自适应性、自学习能力及其行为形成主因子,着重结合操作者行为的相关性-感知作用于判断决策后影响到动作,建立了人机系统中操作者行为模式,并推导出计算操作者可靠度的公式,求出了相应参数.最后进行了实例量度,同时定量辨识了行为相关性对人可靠性的制约程度,以期从人机系统可靠性角度为人机系统的优化设计提供新的依据.     

Process issues in treatment: Application to sexual offender programs.

How critical is the therapeutic alliance in the treatment of sexual offenders? To date such process issues have been neglected in the field of sex offender treatment. This article reviews the literature on the influence on behavior change of therapist features, clients' perceptions, and the therapeutic alliance. Among the many therapist features identified as helpful are empathy, warmth, and being directive and rewarding. Therapists who are aggressively confrontational appear not to foster beneficial changes in their clients. These issues are directly related to treatment issues faced by therapists who work with sexual offenders, such as dealing with cognitive distortions, lack of empathy, and lack of motivation to change. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

High Temperature Oxidation Behavior of La2O3-MosSi3/MoSi2 Composites

The oxidation behavior of 0. 8% La2O3- Mo5Si3/MoSi2 composites at 1200℃ in air was investigated. The results reveal that the oxidation resistance of the material with 0. 8% La2O3 and Mo5Si3 is impaired. The oxidation resistance is decreased with increasing Mo5Si3 content. The mass loss follows a linear law in the initial oxidation. With oxidation time prolonging, a continuous and dense oxidation scale prevents oxygen from diffusing increasing when and leads to mass change a Mo5Si3 content is less than 30%. However, the composite shows ＂PEST＂ with the addition of 40% Mo5Si3. With increasing Mo5Si3 content, the oxidation resistance of 0.8% La2O3- Mo5Si3/MoSi2 decreases. This attributes to the poor oxidation resistance of M05Si3 and the relative density decreasing of 0. 8% La2O3-Mo5Si3/MoSi2 composite.     

A prospective investigation of the impact of childhood sexual abuse on the development of sexuality.

The sexual attitudes and activities of 77 sexually abused and 89 comparison women (mean age=20.41, SD=3.38) were assessed 10 years after disclosure in a longitudinal, prospective study of the long-term effects of childhood sexual abuse. Abused participants were more preoccupied with sex, younger at first voluntary intercourse, more likely to have been teen mothers, and endorsed lower birth control efficacy than comparison participants. When psychological functioning earlier in development was examined, sexual preoccupation was predicted by anxiety, sexual aversion was predicted by childhood sexual behavior problems, and sexual ambivalence (simultaneous sexual preoccupation and sexual aversion) was predicted by pathological dissociation. Findings also indicate that biological father abuse may be associated with greater sexual aversion and sexual ambivalence. (PsycINFO Database Record (c) 2010 APA, all rights reserved)