高压加热器技术简介

介绍了东芝高压加热器技术以及技术转让的一些内容 ,以及为能制造出符合东芝技术要求的高压加热器而采取的保证措施     

Using internal fibre geometry to improve the performance of pin-loaded holes in composite materials

The anisotropic nature of fibre reinforced composites leads to large stress concentrations around pin-loaded holes through standard weave cloths. Proper understanding of how this anisotropic nature affects the load distribution around holes can be utilised to reduce these concentrations if sufficient thought is given to the internal fibre geometry near to the hole. Such local reinforcements need not be highly complex and can be readily produced without excessive effort, producing significant improvements in performance.     

小高层剪力墙结构开洞设计探讨

小高层建筑需通过剪力墙开洞(结构开洞)降低侧向刚度,本文对开洞部位以及墙肢和连梁设计提出一些看法,供设计人员参考。     

Experimental study of composite cold-formed steel C-section floor joists

Twelve large-scale slab specimens and twenty-two companion push-out specimens were tested to study the behavior and capacity of composite slab joists consisting of cold-formed steel C-sections and concrete. Four shear transfer mechanisms, including surface bond, pre-fabricated bent-up tabs, pre-drilled holes, and self-drilling screws, were employed on the surface of the flange embedded in the concrete to provide shear transfer capacity. Results indicated that specimens employed with shear transfer enhancements showed a marked increase in strength and reduced deflection compared with those relying only on a natural bond between steel and concrete to resist shear. Of the three shear transfer enhancements investigated, bent-up tabs provided the best performance at both the strength and serviceability limit states, followed by drilled holes in the embedded flanges. The use of self-drilling screws resulted in the lowest strength increase. The correlation of shear transfer capacity of push-out specimens with the ultimate capacity of large-scale specimens indicated that the average experimental flexural capacity of the slab specimens was approximately 1.16 times the average predicted value based on push-out test results.     

MARK-Ⅳ型气化炉气化剂均布的探讨

通过对炉篦的结构分析 ,并考虑炉内搅拌器的作用 ,结合原料煤的特性 ,提出气化剂均布的原则及方案 ,以改善气化炉操作功效     

基于空洞模型的地理位置路由改进算法研究

针对现有WSN中地理位置路由遇路由空洞后会产生冗余路由的问题,提出一种基于感知空洞形状的分段贪婪路由(Easy Modeling Greedy Routing,EMGR)算法。EMGR引入虚拟坐标概念,利用空洞边界探测包收集空洞边界节点信息,将其映射到虚拟坐标系中;根据空洞边界节点在虚拟坐标系的不同分布,定义凹、凸域来概括路由空洞形状;根据不同的空洞形状找到合适的中转节点,采用分段贪婪路由方式传输数据。仿真实验结果表明,相较于GPSR算法,EMGR算法产生的路由跳数减少了35%,网络能耗低,路径扩张率和网络时延小。     

全顺轮辐小孔冲模设计及异常问题处理

针对V348全顺轮辐小孔冲模试模过程中出现的冲小孔凸模断裂频繁的异常问题,分析了原因,提出了技术改进方案.实现了在厚度为6mm的高强度钢板冲φ8mm小孔的模具设计制造.     

多侧孔零件冲孔模设计

介绍了一副典型的多侧孔冲孔模的设计分析和模具结构。由于多侧孔冲压件，大多数是侧孔布置在冲压件的周围，因而冲孔凹模只能放在冲压件的内部，往往受到冲压件体积的限制，这样冲孔凹模的强度和刚度都受到极大影响，该文介绍了两种方法解决这一问题，可供同行在类似产品设计中参考。     

气体搅动的筛板萃取塔性能实验研究

在筛板萃取塔中引入气体搅动,既能明显提高装置的传质效率,又能大幅提高装置处理能力。筛板塔的通量随气速的变化规律与填料塔有显著区别,其性能研究有重要意义。利用煤油(苯甲酸)-水-空气体系,考察了气体搅动和筛孔直径对萃取塔流体力学和传质性能的影响。结果表明,随着表观气速的增加,气含率、分散相含率、液泛速率和传质效率均明显增加。但过高的气速也会导致分散相的过于分散和乳化,传质性能下降,直至液泛。不同直径的筛孔相比,较小的筛孔使分散相停留时间延长,分散相含率和传质效率提高,但液泛速率和处理能力降低。     

无位置信息的无线传感器网络漏洞发现算法*

无线传感器网络广泛应用的前提是能够检监测目标区域特定事件的发生。而节点能量受限、难补给的特点导致监测性能难以保证,造成监测盲区出现。针对无线传感器网络节点的地理位置信息未知的情况进行了研究,提出覆盖漏洞发现算法CHDA (Coverage Holes Discovery Algorithm),在以节点为极点建立的极坐标中计算出相邻节点的相对位置信息和该节点被其邻居节点覆盖的边缘弧的信息,并且根据节点的单纯覆盖弧序列的定义计算出节点被其邻居节点覆盖的单纯覆盖弧序列,从而得到网络中的覆盖漏洞。覆盖漏洞的发现克服的地理位置信息未知的限制,为漏洞的修补提供了必要的前提条件进而保证传感器网络的覆盖率。