放电等离子烧结钛/氧化铝的界面反应

研究了用放电等离子烧结的Ti/Al2O3在1 200℃和30MPa条件下界面反应特性,用X射线衍射和电子探针微区分析了界面反应类型.结果表明:Ti/Al2O3界面反应为反应扩散型,即氧化铝首先发生分解,分解出的Al原子扩散进入Ti中,扩散距离约为62 μm,界面处Al原子的摩尔分数x高达42.49%,Ti与Al在界面区发生反应,在贫Al区生成Ti3Al相,贫Ti区生成TiAl相等界面产物,O原子固溶于Ti中.     

复合碱、盐多元驱各组分对油水界面张力和稠油黏度的影响

无机盐,混合碱NaOH、Na2CO3,阴离子表面活性剂十二烷基苯磺酸钠(LAS)、脂肪醇聚氧乙烯醚硫酸钠(AES),聚合物聚丙烯酰胺(PAM),经过混合组成多元驱。通过实验探讨了该多元驱中各个组分的用量对油水界面张力和稠油黏度的影响,优化了该多元驱中各个组分的含量。实验得出,无机盐的加入可以显著地降低界面张力和稠油黏度。当多元驱中无机盐、混合碱和表面活性剂的质量分数分别为51.87%,40.17%,6.99%,聚合物质量浓度为800 mg/L,配成质量分数为1%的水溶液,加热到50℃,油水质量比7∶3混合后,可使新疆克拉玛依地区红浅稠油黏度从23690 mPa.s降到84.83 mPa.s,降黏率达到99.64%,体系界面张力达到0.07499mN/m。室内评价表明,该多元驱可使新疆克拉玛依地区9#红浅稠油降黏率达到92%。多元驱中无机盐的质量分数超过50%,大大降低了成本。     

吸收过程的界面传质机理

以分子热力学为基础 ,对气体吸收过程进行了理论分析 ,导出了传质通量的数学表达式。根据该文分析 ,气液界面传质的源动力来自界面处气液两相的不平衡 ,即只要有传质发生 ,液相界面处的浓度就不会达到与气相呈平衡的浓度。对于气相阻力可以忽略的吸收过程 ,两相传质速率的大小主要取决于液相的溶质界面浓度和液膜厚度 ,影响溶质界面浓度和液膜厚度的主要因素是近界面液相侧的流场分布。利用近界面浓度与液膜厚度的激光测定结果 ,计算了甲醇、乙醇及正丙醇吸收CO2 气泡的传质通量 ,计算结果与实验值吻合良好     

聚合物—铝酸—钙界面组成与结构的XPS研究

从复合材料界面的角度,采用XPS综合方法研究了水泥基聚合物复合材料的高强特别是高抗弯强度的微观机理。结果表明,在材料界面上存在明显的电子结合能化学位移效应,并被证实为聚合物与无机水泥的化学键合所致。界面层的深度分析发现,掺加聚合物的材料界面具有良好的化学和物理结构。作者认为这种材料的高强机理主要是由于两种基质界面间的有效化学键合作用,形成了良好的界面结构,因此,可认为这种作用大于有的学者所解释的聚合物的单一物理作用。     

Effect of MgO Addition on the Bondability and Interfacial Reaction between Dielectric and Glass-Ceramics for the Fabrication of Multi-Component Ceramic Substrates

Bondability and interfacial reaction between dielectric and insulator layers have been examined to obtain a basic understanding of bonding mechanisms. Lead-containing complex perovskite was used as a dielectric material. Two kinds of glass-ceramics were used as insulator material; lead borosilicate glass containing Al_2O3 (insulator A) and the same containing Al₂O₃ and M_gO (insulator B). Dielectric and insulator layers did not bond when insulator A was used. When insulator B was used, however, strong bonding was achieved between the two layers by firing the powder compacts at temperatures between 800° and 1000°C. Addition of M_gO to lead borosilicate glass increased the thermal expansion coefficient to that of the dielectric and enhanced the formation of reaction layers, resulting in good bonding. Two reaction layers were identified. The main reaction products were enstatite and bredigite for one layer contacting the dielectric, and enstatite and a compound with the same diffraction pattern as that of faujasite for the other layers contacting insulator B.     

Preparation of dibasic acid-containing soy phospholipids by chemical and enzyme-catalyzed transesterification and evaluation of their surface-active properties

The preparation of dibasic acid-containing soy phospholipid was made by transesterification reaction with alkyl ester of diabasic acid with both lipase and alkoxide as a catalyst. The extent of incorporation of a dibasic acid varied with the molecular size of the dibasic acid. The extent of incorporation in soy phospholipids was 4–13% in the case of adipic acid and 9–20% in the case of sebacic acid. The surface-active properties of these modified soy phospholipids were examined and were found to be different from those of the original (unmodified) soy phospholipid. The interfacial properties such as critical micelle concentration (CMC), γ_CMC, surface excess concentration Γ_max, and minimum area per molecule (Å), and thermodynamic parameters such as standard free energy of micellization, were found to depend on the hydrophobic part of the dibasic acids.     

Dielectric behavior of PVDF/POMA blends that have a low doped POMA content

The real (ε′) and imaginary (ε″) components of the complex permittivity of blends of PVDF [poly(vinylidene fluoride)] with POMA [poly(o‐methoxyaniline)] doped with toluenosulfonic acid (TSA) containing 1, 2.5, and 5 wt % POMA–TSA were determined in the frequency interval between 10² and 3 × 10⁶ Hz and in the temperature range from ?120 up to 120°C. It was observed that the values of ε′ and ε″ had a greater increase with the POMA–TSA content and with a temperature in the region of frequencies below 10 kHz. This effect decreased with frequency and it was attributed to interfacial polarization. This polarization was caused by the blend heterogeneity, formed by conductive POMA–TSA agglomerates dispersed in an insulating matrix of PVDF. The equation of Maxwell–Garnett, modified by Cohen, was used to evaluate the permittivity and conductivity behavior of POMA–TSA in the blends. A strong decrease was observed in POMA–TSA conductivity in the blend, which was bigger the lower the POMA–TSA content in the blend. This decrease could have been caused either by the POMA dedoping during the blend preparation process or by its dispersion into the insulating matrix. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 752–758, 2003     

木塑复合材料界面相容剂的研究进展

木塑复合材料是一种新型的材料,由于其优越的综合性能而越来越受人们所关注.主要介绍了国内外木塑复合材料界面相容剂的分类及其在复合材料中的应用、表征等方面的研究进展.其中,界面相容剂在木塑复合材料中的表征手段主要介绍了静态力学性能测试、动态力学热分析测试(DMA)、接触角测定、扫描电镜(SEM)观测法、傅利叶红外光谱法(FTIR)测定以及X射线光电子能谱法(XPS)测定,并重点闸述了接枝改性聚合物型界面相容剂的制备、反应机理、表征等.闸述了国内木塑复合材料界面相容剂的发展状况,最后介绍了木塑复合材料界面相容剂的发展趋势.     

Synergistic Catalysis of Carbon Dioxide Hydrogenation into Methanol by Yttria-Doped Ceria/γ-Alumina-Supported Copper Oxide Catalysts: Effect of Support and Dopant

Methanol synthesis from carbon dioxide hydrogenation was studied over ceria/-alumina- and yttria-doped ceria (YDC)/-alumina-supported copper oxide catalysts to seek insight into the catalysis at metal–support interfaces. It was found that, in comparison with Cu/-Al₂O₃, the Cu/CeO₂/-Al₂O₃ and Cu/YDC/-Al₂O₃ catalysts exhibited substantial enhancement in activity and selectivity toward methanol formation. The extent of enhancement was augmented by increased ceria loading on -alumina and with increased yttria doping into ceria. The enhancement is inferred to result from the synergistic effect between copper oxide and surface oxygen vacancies of ceria.     

伊朗轻质原油减渣馏分油水界面张力的研究

The vacuum residual from Iranian Light crude oil are separated into a series of 16 narrow fractions according to the molecular weight by the supercritical fluid extraction and fractional (SFEF) technology. The chemical element and the UV spectrum of each fraction are analyzed. The effects of several factors on the interfacial tension are investigated, which are the fraction concentration in oil phase, the ratio of oil component, the salts dissolved in the water phase and the pH value. The interfacial tension decreases rapidly as the concentration of the residual fraction in the oil increases, showing a higher interfacial activity of the fraction. The interfacial tension changes, as the amount of absorption or the state of the fractions in the interface changes resulting from different ratios of oil, different kinds or concentrations of salts in water, and different pH values. It is concluded that the intrfacial tension changes regularly, corresponding to the regular molecular parameters of the vacuum residual fractions.