An investigation of the unstable region for dense phase conveying in sliding bed flow

For fine powdered materials, capable of being conveyed in dense phase, a conveying region exists in which instability in flow and pipeline blockage can occur if the pressure gradient available is insufficient to maintain a minimum value of solids loading ratio. A reduction in material flow rate can also lead to pipeline blockage in this region. Conveying trials under-taken with cement are used to illustrate the nature of the problem.     

空调器用风冷冷凝器换热能力实验研究

实验测定了几种不同铜管、肋片组合的冷凝器在不同的风量和风机转速下的换热量，发现采用内螺纹铜管和迎风侧平片、背风侧冲缝片的冷凝器具有最优的换热性能。分析了多流路冷凝器中不同流路之间的制冷剂分配不均匀性和再热现象。     

超灵敏小型回旋加速器质谱计垂直旋转型多样品装置自动控制系统

本文介绍用于我所超灵敏小型回旋加速器质谱计垂直旋转型多样品装置自动控制系统原理及应用，该系统亦可用于其他多样品自动装置。     

柴油机针阀体的乙炔低压渗碳

乙炔低压渗碳可以有效地避免在真空渗碳过程中产生炭黑和焦油，同时由于乙炔具有较高的供碳能力，使这一技术尤其适用于针阀体这样的小直径深盲孔零件。     

冷轧厂酸洗机组3号横剪大流量中高压液压系统设计方案探讨

在宝钢２０３０ｍｍ冷轧厂酸洗机组中，为了满足厚规格ＩＦ钢的生产，拟将原有的气动式剪切机改成液压式剪切机。为此，设计了一套中高压大流量的液压系统以满足３号横剪大剪切力（最高达７００ｋＮ）和快速剪切（３秒／次）的需要。由于采用了蓄能器增速回路和二通插装阀控制技术，使该液压系统较传统的剪切机液压系统具有响应速度快、体积小、重量轻、发热少和降低电机能耗等优点。     

Thermodynamic Analysis of Various Dehumidifying Dryers for Wood

Typical methods of dehumidification of air circulating in the dehumidifying driers (indirect and direct cooler and partial exchange of the air) were analysed. Energy aspect of cooler operation was evaluated. The method for minimization of unit thermal energy consumption in a dehumidifying drier by the optimal selection of the cooler point was also given. Methods of the heat recovery of heat conveyed in a cooler lending to save energy (heat regeneration. expansion and compression of the air, a dehumidifier) were analysed. It was indicated that introduction of dehumidifiers into contemporary wood driers caused significant improvement of energy aspects of their operation     

沈阳太平洋广场空调冷热源方案比较

对一幢１１．５万ｍ＾２的四星级综合建筑的空调冷热源不同的蓄冷和取冷比较了四种方案，论证了其中直燃型溴化锂吸收式冷热水机组供冷供暖、小型燃油锅炉供蒸汽的方案最为合理。     

MIS型单晶硅液晶光阀

详细介绍了一种新颖、快速响应的金属－绝缘层－半导体构成的MIS型单晶硅液晶光阀的结构、工作机理、制作工艺和性能参数测试。液晶采用45°扭曲向列型混合场效应工作模式。所得到的光阀的极限分辨率为40lp／mm，口径40mm，最大对比度＞100：1，在930nm（△λ＝40nm）写入光灵敏度为20μW／cm2，响应时间为15ms。报道了该光阀在大屏幕投影显示中的应用。     

含氮化合物废气选择性催化氧化技术研究进展

通过对当前含氮化合物废气治理技术的对比分析,总结选择性催化氧化的相关技术优势。根据对含氮化合物的种类及来源分析,介绍氨气、腈类、胺类及其他含氮化合物的催化净化技术。重点总结催化剂的种类、研发进展和在实际使用中可能遇到的问题,同时展望含氮化合物废气选择性催化氧化技术的研发方向。     

The effect of pre-wetting on dynamic contact angles

A roll-coating experimental system is used to study the effect of pre-wetting on dynamic contact angles, the interfacial displacement depth, and the associated phenomenon of air entrainment. The system consists of a roll, which is horizontally rotating in a liquid pool. The dynamic contact angle is recorded by a macrophotography system. The test liquids are glycerol solutions with viscosities in the range 104 < μ < 748 mPa · s. The value of (μV/ρg)^0.5 is taken as the characteristic length to be used in the dimensionless relationships which correlate experimental measurements. The effect of base layer entry angle into the liquid pool on the dynamic contact angles and other flow parameters is studied. Comparison is made with measurements in dry tape-coating and other pre-wet roll–coating systems.