Progressive damage modelling of SMC composite materials

The present work deals with the modelling of damage behaviour for sheet moulding compound (SMC) composite materials using a finite element analysis package. Specifically, a comparison is made between the results obtained experimentally for a three-point bending test, and those obtained from numerical simulation using a material model already implemented. The simulation has been performed for the material models available within the PAM-CRASH software. The simulation results are compared and validated with respect to experimentation.     

A Bluetooth Based Sensor Network for Civil Infrastructure Health Monitoring

Communicating with sensors has long been limited either to wired connections or to proprietary wireless communication protocols. Using a ubiquitous and inexpensive wireless communication technology to create Sensor Area Networks (SANs) will accelerate the extensive deployment of sensor technology. Bluetooth, an emerging, worldwide standard for inexpensive, local wireless communication is a viable choice for SANs because of its inherent support for some of the important requirements – low power, small form factor, low cost and sufficient communication range. In this paper we outline an approach, centered on the Bluetooth technology, to support a sensor network composed of fixed wireless sensors for health monitoring of highways, bridges and other civil infrastructures. We present a topology formation scheme that not only takes into account the traffic generated by different sensors but also the associated link strengths, buffer capacities and energy availability. The algorithm makes no particular assumptions as to the placement of nodes, and not all nodes need to be in radio proximity of each other. The output is a tree shaped scatternet rooted at the sensor hub (data logger) that is balanced in terms of traffic carried on each of the links. We also analyze the scheduling, routing and healing aspects of the resulting sensor-net topology.     

Improving Short-Circuit Current Capacity, Resistance, and Breaking Load of OPGW Constructions by Modifying Aluminium Alloy With AlB2

This article presents a method that can be applied to molten AA-6101 alloy to improve electrical properties of the aluminium part of the optical ground wire (OPGW) used in overhead transmission lines to protect phase conductors from lightning strike and to transmit signals and data. AA-6101 alloy in casting of the log as 6 m length and 178 mm diameter for extrusion has been inoculated by AlB₂ to decrease detrimental effects of Cr, Ti, V, and Zr on the conductivity of the material. After inoculation, improved billets were extruded as 9.5 mm diameter feedstock. Required wires drawn from the feedstock according to the construction types of OPGW to be tested were exposed to aging at 175°C, 6 h (T-8). Upon completion of the back-twist and performing-type stranding process, resistance, and short-circuit current capacity and breaking load of the OPGW 88/44 constructions with other metal combinations have been examined and tested to show improvement. Results are summarized in tables and graphically.     

新安江流域安徽省地区水环境状况分析

统计分析流域内点源污染、面源污染产生量与污染物入河量的调查监测数据,结果表明:安徽省辖新安江流域点源入河系数约为面源入河系数2~3倍,点源污染是流域内主要污染来源,但面源污染的作用不容忽视,尤其是总磷,有近2/3来自面源,相对省辖淮河、长江两流域来说,面源污染贡献率明显增大。指出流域污染防治必须综合考虑点、面源污染两个方面;在点源污染不太严重的情况下,对面源污染的治理必须引起足够的重视,才能取得实效。     

原油基压裂液研究

研制了一种适用于低压、低渗、水敏性储集层的新型原油基压裂液体系。根据基液原油的组分合成相应的增稠剂，增稠剂在原油中与交联剂反应，形成网状结构，使原油成为黏度可以调控的冻胶，从根本上改变了油基压裂液以柴油、煤油为基液的现状，降低了油基压裂液的成本，同时还提高了压裂液的抗温、抗剪切和破胶性能，并将交联时间缩短到2h以内，可以满足现场压裂施工的要求，大大降低了施工强度和压裂改造的综合成本。在青海油田进行的现场先导试验取得成功。图9表1参5     

电子产品研制阶段可靠性增长试验研究

结合工程实际经验,深入讨论了可靠性增长过程及实现途径,在保持试验条件和改进过程不变的条件下,实施了对具体型号电子产品的可靠性增长试验,达到了预期的可靠性增长目标,并且利用可靠性增长试验的数学模型(AMSAA模型)来评估产品的可靠性增长,对开展可靠性增长与可靠性增长试验工作具有重要的实际意义.     

堆石料与基岩面直剪试验

介绍了堆石料与基岩面的现场直剪试验方法，6个组次的直剪试验结果表明，堆石料与基岩面的抗剪强度指标随基岩面坚硬度的增大而增加，并随基岩面粗糙度的加大而加大。     

应用TEXTIO和MATLAB进行复杂数字系统仿真

在基于FPGA的复杂数字系统的仿真测试中,设计者常常面临各种挑战.以数字图像处理系统的仿真为例,如果采用完备性仿真测试方法,那么测试矢量的数量将是非常巨大的;如果采用常规方法,不仅效率不高,而且可能无法达到仿真测试的目的.针对这个难题,提出一种进行仿真测试的新方法,该方法应用TEXTIO和MATLAB来辅助仿真测试过程,使问题得到较好的解决.以电视图像实时多目标捕获单元的仿真测试为例,全面、细致地讨论这种新方法.     

玻璃纤维布内中空纤维丝的检测

介绍了玻璃纤维布内中空纤维丝的检测方法。     

基于Agilent-VEE平台的测试系统设计与应用

美国安捷伦公司(原惠普公司)的Agilent-VEE，NI公司的Lab VIEW和Lab Windows／CVI开发软件等是国际上公认的优秀的虚拟仪器开发平台软件，人们对以应用后两者开发测试系统比较了解，但对VEE在测试系统中的应用少有介绍。本文介绍基于Agilent-VEE平台和GPIB总线的实用测试系统的组成、特点及仪器控制方式。