Strength of limestone-based non-calcined cement and its properties

A new type of cement was prepared with ground limestone powder, blastfurnace slag, steel slag and gypsum without calcination. The fraction of ground limestone powder in the cement was as high as 40 wt%–60 wt% without Portland clinker. All of its physical properties can meet the requirements of masonry cement standards. The impact of limestone content on physical properties of the cement and determined its impact on law was investigated. The steel slag can excit the aquation activity of this cement effectively, and the influence of its quantity on the strength of the materials was studied, which shows that the optimum quantity of mixing is 10%. By way of changing the different content of the lime stone by quartzy sample, the law of the compression strength and the PH value was determined, confirming that the lime stone can promote the early aquation of the slag and improve the early strength. The main hydration product of this cement is calcium aluminate hydrate, ettringite and calcium silicate hydrate, as indicated by XRD and SEM analysis.     

Preparation and characterization of stainless steel/TiC nanocomposite particles by ball-milling method

A stainless steel/10wt%TiC nanocomposite particles were prepared by high-energy ball-milling method using stainless steel, carbon and titanium as raw materials. The evolution of phase composition, microstructure and specific surface area of the stainless steel/TiC nanocomposite particles with increasing ball-milling time in the range of 0–100 h were investigated by XRD, SEM, TEM and BET techniques. The results showed that the stainless steel/TiC nanocomposite particles were fabricated when the ball-milling time was longer than 20 h. However, the nanocomposite particles were soldered and agglomerated again when the ball-milling time was longer than 60 h. The microstructure of the composite particles transformed from lamellar structure to nanostructure during the repeated process of the cold welding and cracking. TEM image reveals clearly that the in-situ TiC nanoparticles with grain size of 3–8 nm are in the interior of the stainless steel/TiC nanocomposite particles obtained by ball-milling 100 h. Funded by the Natural Science Foundation of Hubei Province (No. 2006ABA304)     

结构钢缺口板断裂试验及数值分析

通过对25个结构钢缺口板进行的单向拉伸断裂试验,验证了提出的结构钢广义屈服模型和椭球面断裂准则.用ANSYS软件中的参数化设计语言APDL和用户编程功能UPFs,将提出的静水应力型广义屈服模型编制成子程序模块,对结构钢缺口板断裂试验进行了基于广义屈服模型和椭球面断裂准则的数值模拟分析.试验结果表明:裂纹起始于缺口边缘内侧,裂纹在厚度方向贯通后沿宽度发展,试件最终断裂于缺口薄弱断面.缺口板断裂应力场分析表明,提出的椭球面断裂准则对预测结构钢缺口板初始开裂具有广泛适用性和较高精度.     

控制索原长求解索张拉力的反分析法

为对预应力空间钢结构的施工成形进行系统的研究,提出了基于控制索原长求解索张拉力的反分析法.从预应力状态开始,通过控制每一级张拉索的原长,进行非线性有限元迭代计算,求出索在分级分批施工时的控制力.方法的优点在于计算简单,省去了通用有限元需要反复试算的缺点.应用编制的程序对一弦支穹顶模型进行了施工过程的模拟分析,结果表明:反分析法能精确模拟结构的施工成形过程,且在整个过程中,每根索只需张拉一次,简化了施工工艺.     

新型钢铅组合耗能器性能试验及参数优选

为了考察新型钢铅组合耗能器(NCSLD)的力学性能和提高其耗能能力,利用电液伺服压剪试验机对NCSLD耗能器进行力学性能试验,采用ANSYS实体建模的方法对耗能器进行大量的数值分析,并对性能试验和数值分析的结果进行对比,研究耗能器的滞回特征参数与其6个几何参数之间的关系,回归出二者之间的公式.提出评价耗能器性能优劣的标准及其附加条件,并以此标准为依据,利用均匀设计法和遗传算法分别对耗能器的6个几何参数进行优选.结果表明遗传算法的选优效果要好于均匀设计法,同时得到一系列性能良好的NCSLD耗能器.     

新型冷弯翼缘闭合组合轴压构件力学性能研究

利用冷弯薄壁型钢截面成型灵活的特点,将既有的两类翼缘闭合截面形式经过合理变形,再经两两组合点焊形成两类新型截面形式——翼缘闭合组合截面DHF1、DHF2。采用ANSYS非线性有限元分析方法,针对新型截面轴压构件,建立了有效的分析模型,通过对构件的应力－应变关系曲线、参数变化时的极限应力变化曲线和应力、变形云图,全面考察了截面高度、截面宽度、板件厚度和闭合区高度比等参数对构件的变形模式、屈曲特征、承载力、极限应力等方面力学性能的影响规律。研究结果表明,新型截面轴压构件板件的局部屈曲不易出现,从而具有截面刚度大、承载能力强的特点,对于中、小长细比构件的极限应力常可达到材料的屈服强度,证明提出的冷弯翼缘闭合新型组合截面轴压构件具有较为优越的力学性能,可以深入试验研究并合理推广使用。     

H型截面单层单跨钢框架火灾行为试验

对2榀H型截面单层单跨钢框架进行了火灾行为的足尺试验研究.全部试验采用自行研制的火灾试验炉,试验结果表明炉子性能稳定,使用方便.试验中考虑了不同受火工况对钢框架火灾行为的影响.通过试验得出了钢框架温度场分布和变形的变化规律.试验结果表明:火灾下,梁柱全部受火的单层单跨钢框架(节点受到保护)破坏方式为钢柱压屈破坏,破坏位置在受到保护的钢节点下部的钢柱上.试验研究为今后钢结构火灾行为的研究提供依据.     

板宽对板形影响的实验研究

采用实验的方法对板宽对板形的影响进行了较为系统的研究,发现了板凸度随板宽变化的一些规律。该研究结论对制定与完善板带轧制规程、提高板形质量具有重要意义。     

钢板剪力墙的分类及性能

对钢板剪力墙结构进行分类讨论,分析了墙板本身的力学性能、使用性能以及与框架的相互作用;探讨了内嵌钢板与框架栓接或焊接的典型连接方式,并从制作安装、使用性能和对墙板性能的影响3个方面比较了栓接与焊接的优劣;分析了各类钢板剪力墙的特点和适用范围,为设计人员在工程应用中选择恰当的钢板剪力墙类型提供了参考。     

钢骨-方钢管自密实高强混凝土短柱的轴压承载力

采用统一强度理论对轴心受压钢骨-方钢管自密实高强混凝土短柱的核心混凝土、钢管以及型钢钢骨在三向应力状态下的轴向极限承载力进行了分析;通过引入考虑厚边比影响的等效约束折减系数和考虑尺寸效应影响的混凝土强度折减系数,将方钢管对混凝土的约束等效为圆钢管对混凝土的约束,从而推导出钢骨-方钢管自密实高强混凝土短柱轴压承载力的理论计算公式;将该公式的计算结果与试验结果和已有公式的计算结果进行比较,各结果吻合良好。结果表明：该公式有很强的适用性,对发挥材料潜力、节约材料具有实际意义,并且为此类结构的研究提供了重要的依据。