Measurement of the Timoshenko Shear Stiffness. II: Effect of Transverse Compressibility

This is the second of two papers devoted to the issue of measuring the Timoshenko shear stiffness of thin-walled composite beams. In the first paper, the effect of warping on the effective Timoshenko shear stiffness, as measured through bending tests, was studied. The bending test was simulated using finite-element analysis, and the results indicated that the warping effect was minimal. On the other hand, the evidence suggests that transverse flexibility may have a significant influence on the effective Timoshenko shear stiffness, decreasing the effective shear stiffness at shorter test spans. The purpose of the present study is to further investigate this effect and to explore the use of a sandwich theory to predict the measurement error. A higher-order sandwich theory, which captures the transverse strain at concentrated loads and supports, is applied to a commercially available thin-walled composite beam. The results indicate that the sandwich model does capture the decrease in the effective shear stiffness at short spans, and the dependence of the shear stiffness on span-to-depth ratio is similar to that calculated in the first paper, using the finite-element method.     

Tedesko’s Philadelphia Skating Club: Refinement of an Idea

This paper presents new aspects of Anton Tedesko’s design for an important thin shell concrete roof. The study of this roof results from the examination of original engineering drawings and calculations which we present with the goal of promoting a greater understanding of the structural design of a major figure in the tradition of 20th century building.     

喷射沉积SiCP/Al复合材料及6066铝合金热挤压工艺的研究

作者应用喷射共沉积工艺制备 6 0 6 6 / Si Cp复合材料和 6 0 6 6铝合金锭坯 ,在不同的挤压比、挤压温度下挤压成　　型 ,用金相显微镜观察材料的显微组织 ,并测试了材料的力学性能。结果表明 :Si C/ Al复合材料喷射沉积状态的组织很疏松 ,存在许多的间隙 ,其密度约为理论密度的 86 % ,Si C颗粒在复合材料中分布不均匀 ,喷射沉积铝合金基体的致密度可达 90 % ;挤压过程使 Al/ Si Cp复合材料的大多数空隙消失 ,致密程度随挤压比的增大而增大 ,挤压比超过 14 .7后不会明显变化 ,而铝合金基体的致密程度与挤压比的变化关系不明显 ;挤压温度对材料的致密程度影响不大 ;Al/ Si Cp复合材料性能在挤压比超过 14 .7后变化不大 ;铝合金的性能不受挤压比变化的影响 ;而挤压温度过高使材料性能下降     

具有随机输入的混合复合动态系统的稳定性判据

本文给出了如图1所示的具有随机输入的混合复合动态系统的稳定性分析,所讨论的系统由一个算子L和一个随机微分方程描述的方块组成。对于这样的系统,我们建立了随机吸引性、随机渐近稳定性、随机有界性、大范围随机渐近稳定性、p吸引性、渐近p稳定性、一致p有界性和大范围渐近p稳定性的判据。这些判据包含了一些假设,这些假设描述了算子L和整个系统的定性I/O性质和表示了由随机微分方程描述的子系统的性质。     

实用钢筋混凝土梁板结构优化设计

本文比较全面地考虑了钢筋混凝土梁板结构实际设计时的全部必要约束,给出了一套(单跨矩形和T形梁、单向板、按弹性理论计算的双向板和矩形等截面连续梁)简单实用的近优化设计的解析公式,为编制其优化设计的实用程序和图表提供了根据.     

Modelling and analysis of 3-D arrangements of particles by point processes with examples of application to biological data obtained by confocal scanning light microscopy

Within the concept of point processes, a review is presented of quantities which can be used in studies of three-dimensional (3-D) aggregates of particles. Suitable characteristics and estimators are given for both unmarked and marked point processes. To demonstrate the feasibility of such quantitative approaches, an application in histology, dealing with 3-D arrangements of cell nuclei in rat liver, is described. Using a confocal scanning light microscope, 3-D images are recorded and image analysis used to obtain the coordinates of the centroid, together with the volume and DNA content, of each cell nucleus. Examples of results are given, using both unmarked and marked point processes. In the latter case, cell type, nuclear volume and ploidy group are suitable marks.     

硼／铝复合材料管构件的界面特性EI

主要研究带钛合金连接头硼／铝复合材料管构件中Ｂ－Ａｌ－Ｔｉ间的界面结构与性质。研究表明，在复合工艺条件下，硼－铝界面附近没有检测到任何铝－硼化合物，而钛－铝间形成ＴｉＡｌ有序金属间化合物相。实验证明，硼／铝复合材料与铝合金端环之间采用的固结方法是有效的，且可按照受载类型随意调整斜面搭接长度，达到承受不同载荷的目的。     

WC对Cu/WC_P复合材料性能及组织的影响

通过ＷＣ含量对ＷＣ／Ｃｕ复合材料性能的影响，确定了冷压－烧结法制备Ｃｕ／ＷＣ材料的适宜ＷＣ含量为１０ｖｏｌ％左右。并就ＷＣ对该材料组织和再结晶行为的影响进行了有益的探讨。     

氧化铝/锌合金复合材料界面的SEM观察

利用挤压铸造制备氧化铝／锌合金复合材料，在扫描电镜（ＳＥＭ）上观察复合材料的界面。结果表明，在复合材料中纤维与基体间存在致密界面层，合金元素通过适当的化学反应可改善纤维与基体间的结合；在凝固过程中，纤维／基体界面上的硅在共晶体的共生生长过程中起了领先相作用，导致复合材料的共晶转变是由铝硅共晶转变和锌铝共晶转变两者组成。