Studies on high density polyethylene (HDPE) functionalized by ultraviolet irradiation and its application

The structure and properties of high density polyethylene (HDPE) functionalized by ultraviolet irradiation at different light intensities in air were studied by electron analysis, FTIR spectroscopy, contact angle with water, differential scanning calorimetry and mechanical properties measurement. The results show that oxygen‐containing groups such as C?O, C—O and C(?O)O were introduced onto the molecular chain of HDPE following irradiation, and the rate and efficiency of HDPE functionalization increased with enhancement of irradiation intensity. After irradiation, the melting temperature, contact angle with water and notched impact strength of HDPE decreased, the degree of crystallinity increased, and their variation amplitude increased with irradiation intensity. Compared with HDPE, the yield strength of HDPE irradiated at lower light intensity (32 W m^?2 and 45 W m^?2) increases monotonically with irradiation time, and the yield strength of HDPE irradiated at higher light intensity (78 W m^?2) increases up to 48 h and then decreased with further increase in irradiation time. The irradiated HDPE behaved as a compatibilizer in HDPE/polycarbonate (PC) blends, and the interface bonding between HDPE and PC was ameliorated. After adding 20 wt% HDPE irradiated at 78 W m^?2 irradiation intensity for 24 h to HDPE/PC blends, the tensile yield strength and notched Izod impact strength of the blend were increased from 26.3 MPa and 51 J m^?1 to 30.2 MPa and 158 J m^?1, respectively. Copyright © 2003 Society of Chemical Industry     

利用静电学和测量数据对碳纳米管膜场致发射规律的定量分析

碳纳米管膜的场致发射电流密度仅由它表面的宏观电场决定，无论其表面形状是平的还是半球状的。对于理想的平行板电极系统，其表面电场强度均匀（UId），发射电流密度、总电流与发射面积成正比：对于半球一平面电极系统半球形的阴极存在一个宏观场增强因子ks，一个与两极距离和球半径之比（d/r）相关的函数，其表面的平均场强为ks U/d。对于d/r=0，ks=1，d≥r的情况，ks接近于常数。对于10〈d／r〈100的情况，存在一个经验的表达式：ks=1＋0．15d/s=0．005（d／r）^2。在引入ks后，不同作者给出的平面电极系统和半球一平面电极系统碳纳米管膜的场致发射电流I与宏观表面电场强度E的关系都可以近似用-经验公式描述：I=a（E-Eo）^b，a，b为常数。该经验公式可为稳定生产的CNT膜片应用产品设计提供方便。     

催化重整装置进料/产物换热器泄漏的检测及判断

介绍了三种检测及判断催化重整装置进料/产物换热器泄漏的方法及原理,并在某工业装置上加以运用的情况.其中芳烃含量法是根据产物分离罐底物料和重整汽油芳烃含量变化来判断;转化率比较法是根据特定环烷烃的转化率来判断;示踪剂法是在原料中注入苯酚,再根据产物分离罐底物料中是否存在苯酚来判断.     

机械力化学作用对低介硅灰石瓷料的相变和相组成的影响

采用X射线衍射仪(XRD)、差热分析(DTA)手段详细研究了由氧化物粉末制备硅灰石陶瓷时,机械力化学作用及后续热处理对硅灰石陶瓷相组成和相变过程的影响,分析了机械力化学在球磨过程中的作用机理主要是细化晶粒、使晶格畸变、晶格缺陷增多、非晶化和诱导低温化学反应。结果表明:高能球磨中的机械力化学作用能够有效地降低硅灰石陶瓷的烧成温度(11160~11220℃)。探明了经高能球磨的样品在烧成过程中的晶相转变规律。瓷料最终的晶相为单一的-硅灰石(高温变体)。     

热管传热性能对小型热管换热器散热效能影响

在零重力辅助下,小热管热阻是小型热管换热器散热效能的重要影响因素之一。基于集总参数法对于换热器系统数值计算的高效性思想,建立了热管、热管换热器的集总参数模型。对同一热管换热器选用不同传热性能的热管,在不同传热温差和流体质量流速下,就其散热效能进行了数值计算。计算结果表明,在零重力辅助下,热管换热器管内热阻存在一临界值Rcri。当热阻RHP≤Rcri时,管外热阻起主导作用,热管换热器的散热效能εh几乎不随热管管内热阻的值而变化。     

An Acoustic Converter Used to Measure Ionizing Radiation Energy Loss

A monitor is proposed based on ultrasonic production when ionizing radiation passes through a medium. The recording element is a 0.2 mm aluminum plate mounted in a ceramic acoustic converter AC in the form of a wedge of thickness 2 mm. The low plate thickness minimizes the beam parameter distortion, while special technology used in the AC provides high sensitivity. The device has been calibrated in the proton beam from the ITEP accelerator at 200 MeV with 2·10⁹–6·10¹⁰ particles in a pulse and a pulse length of 70 nsec.     

天然气吸附储存脱附过程的动态模拟

通过热动力学计算,认识了脱附过程当中储罐内温度剖面分布的典型特征:储罐轴心处的温度下降幅度最大。分析了脱附过程当中储罐壁的热交换、吸附剂的导热系数以及储罐内的初始压力对储罐内的温度剖面的影响。结论是加强储罐外壁的热交换、增大吸附剂的导热系数皆能改善吸附储罐内的温度剖面。     

Thermodynamic and Transport Properties of Liquid HFC-227ea

The thermal conductivity and heat capacity of liquid 1,1,1,2,3,3,3-hepta-fluoropropane (HFC-227ea) have been studied by a high-frequency thermal-wave method over the temperature range of 294 to 345 K at pressures up to 2.8 MPa. The purity of the samples used throughout the measurements is 99.99 mol%. The experimental uncertainties of the thermal conductivity and heat capacity measurements were estimated to be within ±1.5 and ±2%, respectively. The thermal conductivity of HFC-227ea in the liquid phase decreases as temperature increases, while the pressure has an opposite effect.     

入射光的偏振和强度对分光镜透／反比的影响

采用能量流分析法推导了一束线偏振光经分光镜分光形成透射／反射光的能量表达式。分别讨论了入射光强度不变而偏振方向变化以及二者同时变化对分光镜透／反比的影响。通过旋转主光路中的偏振片来模拟入射光的偏振方向和强度变化，实验验证了分光比的变化规律。     

混合乳化剂的优选及抗高低温水包油钻井液的研制

O/W乳化钻井液用的阴离子/非离子混合乳化剂,其中的非离子乳化剂先用PIT法初选,再以O/W乳状液黏度为性能指标,用HLB法选定,其中的阴离子乳化剂也用HLB法筛选。选定的一对非离子和阴离子乳化剂按不同比例复配,利用混合表面活性剂HLB值的加和性原理,由O/W乳状液黏度-HLB值关系确定二者最佳配比。O/W乳化钻井液以体积比70/30的柴油 原油为油相,油水相体积比40/60-60/40,乳化剂加量为油水总体积的4%-7%,加入的主要处理剂有:一种代替膨润土的成胶剂,抗高温液体抑制剂,油溶性储层保护剂,降滤失剂等。该钻井液在180℃、最高压力2.5 MPa下热处理24小时或在-26℃冷冻24小时后解冻,均不发生破乳,性能不恶化;用-26℃冷冻7天的乳化剂配制的钻井液,常温和热处理后性能良好。该钻井液流变性能良好,动塑比0.23-0.60,静切力2-8/2-10 Pa,滤失量为零,抑制性良好。图1表3参4。