一种抗运动干扰的实时心率提取方法

针对基于容积脉搏波（PPG）提取运动心率时，传统心率提取算法由于运动噪声干扰使测量结果误差大、实时性不好的问题，提出一种抗运动干扰的实时心率提取方法。该方法通过实时小波去噪，同时结合三轴加速度信号（ACC）对运动进行分类训练，计算各运动状态心率增益，对实时心率值进行补偿。实验结果表明，通过与同时采集的ECG信号计算出的实时心率进行对比，绝对误差率仅为1.2%左右。相比传统心率提取算法，该算法具有抗干扰性强，实时准确的特点。     

一种5 重real-time PCR筛查转基因水稻方法的建立

以转基因水稻中最常用的CaMV35S启动子、NOS终止子、Cry1Ab/Ac基因、HPT基因及SPS水稻内标基因为研究对象，利用5 种不同的荧光信号（FAM、HEX、Taxas Red、Cy5、Cy5.5）进行多重实时聚合酶链式反应（real-time polymerase chain reaction，real-time PCR）检测方法的研究。通过引物组合筛选、反应体系优化、特异性测试、灵敏度测试、适用性测试等一系列实验，建立了5 重real-time PCR方法，灵敏度可达0.032%。此方法具有灵敏度高、结果准确、通量大等优点，可实现水稻中转基因成分的快速、高效检测。     

Structure and phase-composition of Ti-doped gas atomized Raney-type Ni catalyst precursor alloys

Raney-type Ni precursor alloys containing 75 at.% Al and doped with 0, 0.75, 1.5 and 3.0 at.% Ti have been produced by a gas atomization process. The resulting powders have been classified by size fraction with subsequent investigation by powder XRD, SEM and EDX analysis. The undoped powders contain, as expected, the phases Ni₂Al₃, NiAl₃ and an Al-eutectic. The Ti-doped powders contain an additional phase with the TiAl₃ DO₂₂ crystal structure. However, quantitative analysis of the XRD results indicate a far greater fraction of the TiAl₃ phase is present than could be accounted for by a simple mass balance on Ti. This appears to be a (Ti_xNi_1−x)Al₃ phase in which higher cooling rates favour small x (low Ti-site occupancy by Ti atoms). SEM and EDX analysis reveal that virtually all the available Ti is contained within the TiAl₃ phase, with negligible Ti dissolved in either the Ni₂Al₃ or NiAl₃ phases.     

A miniature triaxial apparatus for investigating the micromechanics of granular soils with in situ X-ray micro-tomography scanning

The development of a miniature triaxial apparatus is presented. In conjunction with an X-ray micro-tomography (termed as X-ray μCT hereafter) facility and advanced image processing techniques, this apparatus can be used for in situ investigation of the micro-scale mechanical behavior of granular soils under shear. The apparatus allows for triaxial testing of a miniature dry sample with a size of \mathrm{8}\hspace{0.17em}\mathrm{mm}\times \mathrm{16}\hspace{0.17em}\mathrm{mm} (diameter \times height). In situ triaxial testing of a 0.4–0.8 mm Leighton Buzzard sand (LBS) under a constant confining pressure of 500 kPa is presented. The evolutions of local porosities (i.e., the porosities of regions associated with individual particles), particle kinematics (i.e., particle translation and particle rotation) of the sample during the shear are quantitatively studied using image processing and analysis techniques. Meanwhile, a novel method is presented to quantify the volumetric strain distribution of the sample based on the results of local porosities and particle tracking. It is found that the sample, with nearly homogenous initial local porosities, starts to exhibit obvious inhomogeneity of local porosities and localization of particle kinematics and volumetric strain around the peak of deviatoric stress. In the post-peak shear stage, large local porosities and volumetric dilation mainly occur in a localized band. The developed triaxial apparatus, in its combined use of X-ray μCT imaging techniques, is a powerful tool to investigate the micro-scale mechanical behavior of granular soils.     

Effect of spatial constraints on the phase evolution of YFeO3-based nanopowders under heat treatment of glycine-nitrate combustion products

Formation and structural transformations of yttrium orthoferrite crystals have been studied using X-ray diffractometry, Mössbauer spectroscopy and transmission electron microscopy combined with electron microdiffraction. Said processes have been studied under heat treatment of glycine-nitrate combustion products. There have been identified formations of three structural yttrium orthoferrite modifications – amorphized hexagonal <h₁>-YFeO₃ (P6₃cm) and nanocrystalline hexagonal h₂-YFeO₃ (P6₃/mmc), as well as nanocrystalline orthorhombic o-YFeO₃ (Pbnm), which are selectively formed depending on available three-dimensional confinements. Based on the analysis of changes in the fluid and size composition formulation, it has been proposed mechanism for formation and transformation of YFeO₃ nanocrystals, including growth stage of h₂-YFeO₃ crystals due to amorphized phase of <h₁>-YFeO₃ up to critical size of about 15?nm and their subsequent transformation into orthorhombic form o-YFeO₃.     

Precipitating spinel into precursor glass and its assistance in crystallization

The crystallization phenomena of spinel in CaO-MgO-Al₂O₃-SiO₂-Fe₂O₃ glass have received much attention due to the particular role in preparation of glass-ceramic materials, which represent an effective option to manage hazardous waste. In this study, both preliminary spinel and secondary spinel were precipitated in the precursor glass. The formation of these spinel was meticulously assessed by a combination of X-ray diffractometry and scanning electron microscopy. The structure of the microenvironment in the precursor glass was characterized by Raman spectrums. These advanced techniques highlight the potential for one-step crystallization of the glass. The investigation, which focused on one-step crystallization, demonstrated the growth of pyroxene on spinel accompanying a migration of chromium. The results also show the microstructure of the obtained glass-ceramic was very dependent on the heat-treat temperature. This study not only unambiguously reveals the precipitation mechanisms of spinel but also provides more documentation for one-step crystallization in the glass-ceramics field.     

Formation and wear mechanism of nickel titanium intermetallics during heat treatment of nickel coating on Ti-6Al-4V substrate

In the present work, inter-diffusion of nickel and titanium and formation of Ni-Ti intermetallic compounds on Ti-6Al-4V substrate have been studied. Initially, nickel was electrodeposited on the alloy using a modified Watts bath solution at a current density of 2 A dm^?2 for 1?h. The coated specimens were then heat treated for different durations at 750, 800 and 850 °C under argon atmosphere. The effects of temperature and time on the characteristics, hardness and wear resistance of intermetallic phases were investigated. The results showed that a multilayer structure was formed after heat treatment, an outer layer of residual nickel, an area of intermetallic layers with different compositions followed by a solid solution of Ni-Ti. It was also observed that an increase in time or temperature at first led to the formation of thicker intermetallic layers; however, after passing a critical point, the intermetallic layers seem to dissolve into the substrate. Furthermore, the wear rates of the diffusion treated samples were four times lower compared to Ti-6Al-4V alloy when sliding against AISI 52100 hardened steel.     

Producing fully-lamellar microstructure for wrought beta-gamma TiAl alloys without single α-phase field

Fine-grained fully-lamellar (FL) microstructure is desired for TiAl components to serve as compressor/turbine blades and turbocharger turbine wheels. This study deals with the process and phase transformation to produce FL microstructure for Mo stabilized beta-gamma TiAl alloys without single α-phase field. Unlike the α + γ two-phased TiAl or beta-gamma TiAl with single α-phase field, the wrought multi-phase TiAl–4/6Nb–2Mo–B/Y alloys exhibit special annealing process to obtain FL microstructure. Short-term annealing at temperatures slightly above β-transus is recommended to produce the desired FL microstructure. The related mechanism is to guarantee the sufficient diffusion homogenization of β stabilizers during single β-phase annealing, and further avoid α decomposition by α → γ + β when cooling through α + β + γ phase field. The colony boundary β phase contributes to fine-grained nearly FL microstructure, by retarding the coarsening of the α phase grains.