Development and characterization of magnetorheological polymer gels

Magnetorheological materials have been used in many applications in recent years. To develop new materials, polyurethane and silicone polymer gels were investigated. Rheology is qualitatively controlled for each system by controlling the concentration of reactants and diluents. The resulting polymers have solid, gel, or liquid states, depending on the crosslinking and dilution. The gels were characterized through kinetic analysis. Differential scanning calorimetry (DSC) was used with analysis methods to find the kinetic properties for diluted and undiluted polyurethane systems. Heat of reaction, order of reaction, preexponential constant, and activation energy were obtained from the experimental DSC data. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2733–2742, 2002     

Microstructure-related fracture toughness and fatigue crack growth behaviour in toughened, anhydride-cured epoxy resins

Fracture toughness and fatigue crack propagation (FCP) of plain and modified anhydride-cured epoxy resin (EP) were studied at ambient temperature. Liquid carboxyl-terminated acrylonitrile-butadiene (CTBN) and silicon (SI) rubber dispersions were used as tougheners for the EP. The morphology of the modified EP was characterized by dynamic mechanical analysis (DMA) and by scanning electron microscopy (SEM). The fracture toughness, K_c, of the compositions decreased with increasing deformation rate. K_c of the EP was slightly improved by CTBN addition and practically unaffected by incorporation of the SI dispersion when tests were performed at low cross-head speed, v. Both modifiers improved K_c at high v, and also the resistance to FCP, by shifting the curves to higher stress intensity factor ranges, ΔK, by comparison with the plain EP. It was established that both fracture and fatigue performance rely on the compliance, J_R, at the rubbery plateau, and thus on the apparent molecular mass between crosslinks, M_c. The failure mechanisms were less dependent upon the loading mode (fracture, fatigue), but differed basically for the various modifiers. Rubber-induced cavitation and shear yielding of the EP were dominant for CTBN, whereas crack bifurcation and branching controlled the cracking in SI-modified EP. The simultaneous use of both modifiers resulted in a synergistic effect for both the fracture toughness at high deformation rate and the FCP behavior.     

顺丁橡胶生产过程"门尼升值"的原因研究

研究了顺丁橡胶生产过程中门尼升值的原因。结果表明，顺丁橡胶生产后处理的膨胀干燥过程存在门尼升值现象。不同内在质量的顺丁橡胶门尼升值不同，正常条件下门尼升值发生于门尼粘度的测试过程。     

A new ‘tailor-made’ methodology for the mechanical behaviour analysis of rubber-like materials: I. Kinematics measurements using a digital speckle extensometry

This paper is the first part of a work devoted to the setting-up of a methodology for the mechanical behaviour characterization of rubber-like materials, using a digital speckle extensometer. We present here the experimental approach, specific to large strain measurements. The proposed method is based on in-plane kinematics measurements using an optical extensometer. The whole two-dimensional field of in-plane displacements is obtained by a digital image processing. We discuss then the correlation calculations and how to achieve the optimal subset matching. Next, we specify how to derive the principal stretch ratios, and the accuracy on these components, issued from a subsequent numerical calibration.Finally, we present experimental data dealing with a carbon black, filled natural rubber, issued from uniaxial traction tests, pure shear tests, and tensile tests performed on double-edge notched tensile specimens.     

影响喷气燃料与橡胶相容性的因素

采用几种具有不同初始物理性能及不同丙烯腈含量、不同硫化剂和硫化程度的丁腈橡胶，考察了其配方和物理性能对采用不同工艺条件生产的喷气燃料的相容性。结果表明，喷气燃料与橡胶的相容性不仅与喷气燃料的加工工艺有关，而且与橡胶的组成及其制备工艺有关。采用非加氢工艺生产的喷气燃料与橡胶的相容性好于采用加氢工艺(特别是加氢裂化工艺)生产的喷气燃料。橡胶材料的初始力学性能的好坏并不完全决定其与喷气燃料相容性的好坏，橡胶材料的耐过氧化物侵蚀能力才是影响相容性好坏的主要因素。橡胶的组成和其制备工艺决定了橡胶在喷气燃料中萃取物的数量和组成，不同萃取物的综合作用给相容性带来不同程度的影响。用硫作硫化剂的橡胶虽然原始强度低于用过氧化物作硫化剂的橡胶，但前者与喷气燃料的相容性却远好于后者。     

Preparation and properties of silicone‐containing poly(methyl methacrylate) gels

Poly(methyl methacrylate) (PMMA) gels with varying amounts of silicone and solvent and constant amounts of crosslinker were prepared by solution free radical crosslinking copolymerization of methyl methacrylate (MMA), ethylene glycol dimethacrylate (EGDM), tetraethoxysilane (TEOS) and vinyltriethoxysilane (VTES) comonomer systems. They were then studied in benzene at a total monomer concentration of 3.5 mol L^?1 and 70 °C. The conversion of monomer, volume swelling ratio, weight fraction and gel point were measured as a function of the reaction time, silicone concentration and benzene content up to the onset of macrogelation. Structural characteristics of the gels were examined by using equilibrium swelling in benzene, gel fraction and Fourier‐transform infrared (FTIR) analysis. The morphology of the copolymers was also investigated by SEM. Based on the obtained results, it was concluded that the FTIR data did not have the capacity to show the presence of the VTES or TEOS moiety in these kinds of copolymers. On the other hand, the variation of weight fraction of gel, W_g, and its equilibrium volume swelling ratio in benzene, q_v, exhibited the same behaviour as that of MMA/EGDM copolymers. Also, the dilution of the monomer mixture resulted in an increase in the gel point and swelling degree and a decrease in the percent of conversion and gel fraction. Finally, TEOS is not an ideal silicone compound for reaction in the MMA/EGDM copolymerization system, whereas VTES is a suitable silicone comonomer for this system and it has been proved useful. Copyright © 2005 Society of Chemical Industry     

A comparative study of short nylon fiber—Natural rubber composites prepared from dry rubber and latex masterbatch

A novel method for the preparation of short nylon fiber–natural rubber composites was developed in which short fibers chopped to approximately 6 mm were incorporated in the latex stage and processed into sheet form. By this method, mixing cycle time was reduced without compromising the fiber dispersion. Fiber breakage during mixing was reduced. The new composites when compounded with a dry bonding system based on hexamethylenetetramine, resorcinol and hydrated silica (HRH) showed improved modulus, tensile strength and abrasion resistance compared to conventional composites. Tear strength, resilience, and compression set were similar to the conventional composites. SEM analysis indicated better interaction between matrix and fibers in the case of latex master batch. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Prediction of the twisting moment and axial force in a circular rubber cylinder for combined extension and torsion based on the logarithmic strain approach

The scope of the present work is the application of a particular class of strain energy function, based on the logarithmic strain, for the prediction of the twisting moment and axial force of a rubber circular cylinder under combined extension and torsion. The strain energy function involves four material parameters three of which are determined by fitting published experimental data from simple tensile and compression tests of natural rubber. One of the parameters of the proposed model has physical meaning, and it is equal to one ninth of the initial modulus of elasticity of the material. Hence, the number of unknown parameters is reduced to three. The logarithmic strain energy function is then applied to a combined extension and torsion problem of a rubber circular cylinder to check its performance for more complicated deformations. The results are compared with corresponding experimental and theoretical solutions available in the literature to validate the proposed model. It is found that the proposed strain energy function apart from predicting the common modes of deformations is also capable to determine more complicated types of deformation. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Morphological aspects of rubber fracture and wear

Morphology of carbon black (CB)‐filled rubber was studied with AFM and SEM and the classification of filler agglomerates, based on their internal structure and filler–matrix interactions, has been proposed. It varies according to the activity of CB and the kind of rubber. It has been shown that fracture of rubber starts either inside filler agglomerates (de‐cohesion) or in a filler–matrix interphase (de‐adhesion) initiating wear of the material. Microscopic observations correlate well with TGA and EPR data of wear debris collected during friction of rubber. The increase of thermal stability of CB and the appearance of additional spin signals, respectively, for elongated samples or debris, are proposed to be associated with de‐cohesion or de‐adhesion of the agglomerates. New approach to the fracture of rubber called “fatal agglomerate concept” is presented. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

橡胶Mooney—Rivlin模型材料系数对轴向刚度影响分析

在橡胶小变形范围内，采用理论推断的方法，得到在相同硬度下橡胶Mooney—Rivlin模型材料系数由C2／C1决定的关系式。并采用ABAQUS有限元软件分析的方法，结合橡胶轴向刚度常规解，分析了C2／C1不同值对橡胶轴向刚度的影响进行，结果显示其影响呈现一定规律性。